Project Files of NUCLEO-WL55JC1 Library for Proteus: STM32WL LoRa Pager Simulation
42544a4d70e64d389d374e2f758b23d0.zip

NUCLEO-WL55JC1 Library for Proteus V1.0
NUCLEO-WL55JC1 Library for Proteus V1.0 comes as a ZIP archive of 294 files (3.2 MB, 7.2 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code.
- LIBProteus library
- DLLProteus model
- DSNProteus simulation
- INOArduino sketch
- LIBArduino library
- HEXHEX firmware
- SRCSource code
Description
NUCLEO-WL55JC1-Library-for-Proteus-v1.0.zip with ST's NUCLEO-WL55JC1 in Proteus (your sketch with D0 .. D15, A0 .. A5, LD1 .. LD3, B1 .. B3, LoRa to the other TEP LoRa boards and a serial monitor; TEPWL55.LIB, TEPNET.DLL and the TEP Boards for Proteus add-on 1.71.0), the two-board LoRa pager demo with its sketches and a README.
File Structure
1.1 KB7.7 KB11 KB8.5 KB1.5 KB1.7 KB1.9 KB5.7 KB4.9 KB1.1 KB5.8 KB9.6 KB7.2 KB2.5 KB2.1 KB1.9 KB2.1 KB4.4 KB1.1 KB3 KB3 KB1.8 KB2.5 KB3.5 KB149 B2.7 KB2 KB6.4 KB3.2 KB1.3 KB963 B8.6 KB5.9 KB6 KB12 KB1.6 KB1.3 KB14.7 KB4.3 KB6.1 KB20.1 KB8.2 KB2 KB4.5 KB311 B12.8 KB6.7 KB6.1 KB2.2 KB3.4 KB5.9 KB1.5 KB1.6 KB16.6 KB9.7 KB6.9 KB2.1 KB533 B5.7 KB7.4 KB514 B1.7 KB896 B481 B1.4 KB1012 B482 B936 B559 B467 B3.6 KB3.8 KB504 B956 B575 B455 B8.3 KB10.9 KB522 B79 B5.5 KB3.1 KB79 B442 B918 B1.4 KB1.8 KB1 KB1.3 KB1.4 KB1.8 KB1.4 KB5.7 KB502 B463 B5 KB6.5 KB3.4 KB3.4 KB500 B1.6 KB368 B406 B466 B404 B444 B460 B477 B739 B448 B1.3 KB350 B5.7 KB4 KB562 B1.5 KB2 KB550 B7.2 KB4.1 KB371 B4.5 KB3.5 KB492 B390 B478 B6.6 KB2.4 KB479 B5.1 KB1.9 KB1.3 KB1.3 KB750 B1.3 KB490 B2.2 KB1.9 KB498 B1.2 KB1.2 KB487 B5.1 KB4.6 KB371 B1.5 KB1.2 KB478 B6.2 KB3 KB1.5 KB1.7 KB469 B1 KB1.7 KB433 B294 B358 B1.3 KB2.5 KB13.2 KB3.8 KB659 B510 B4.4 KB1.9 KB5.8 KB11 KB835 B518 B6.4 KB2.3 KB29 B436 B9.2 KB4.9 KB439 B4.2 KB1.5 KB9.3 KB7.1 KB4.7 KB2.4 KB388 B5.1 KB893 B667 B1.3 KB5.5 KB2.3 KB1.8 KB468 B882 B530 B791 B487 B894 B2 KB730 B646 B2.6 KB977 B702 B20.6 KB1.8 KB11.8 KB3.2 KB596 B406 B6.3 KB5.7 KB9.3 KB7.7 KB7.7 KB6.1 KB5.8 KB5.9 KB6.4 KB6.4 KB5.3 KB5.6 KB5.7 KB7.9 KB7.7 KB6.5 KB6.3 KB6.2 KB10.3 KB8.5 KB6.6 KB7.6 KB6.7 KB6.1 KB6.7 KB8.3 KB6.2 KB7.2 KB5.9 KB5.6 KB5.7 KB6.7 KB5.9 KB6.2 KB6 KB6 KB6.1 KB6.3 KB6 KB6.1 KB6.2 KB6 KB5.8 KB6.4 KB6.4 KB6.9 KB6 KB6.8 KB7 KB6.4 KB6.5 KB6.5 KB6.6 KB6.5 KB5.6 KB5.9 KB7.5 KB3.8 KB5.4 KB7.7 KB7.1 KB5.8 KB5.9 KB5.9 KB6.9 KB5.7 KB5.9 KB5.5 KB5.5 KB7.1 KB5.2 KB34.9 KB25.9 KB1.3 KB8.5 KB35.8 KB4.5 KB4.4 KB37.2 KB2.9 MB2.9 MB16 KB37.1 KB36.9 KB11.5 KBGallery12 images from the tutorialOpen the tutorial
The circuit, the board and the results as they appear in NUCLEO-WL55JC1 Library for Proteus: STM32WL LoRa Pager Simulation. Open an image for its full size.












README
NUCLEO-WL55JC1 LIBRARY FOR PROTEUS - V1.0 (YOUR ARDUINO SKETCH, LORA, THREE LEDS AND THREE BUTTONS)
Designed by The Engineering Projects
www.TheEngineeringProjects.com
IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
https://www.theengineeringprojects.com/2026/11/nucleo-wl55jc1-library-for-proteus.html
Report a bug or suggest a feature (our forum):
https://www.theengineeringprojects.com/forum
Our other LoRa board (the same LoRa air in the simulation):
https://www.theengineeringprojects.com/2026/11/arduino-mkr-wan-1310-library-for-proteus.html
Support us (the libraries are free):
https://www.theengineeringprojects.com/donate
FILE STRUCTURE
NUCLEO-WL55JC1-TEP-v1.0/
|-- Proteus Library Files/
| |-- TEPWL55.LIB 37.2 KB the NUCLEO-WL55JC1, to LIBRARY
|-- Proteus Model Files/
| |-- TEPNET.DLL 2.93 MB the board + monitors + network, to MODELS
|-- Arduino Code/
| |-- WL55_Pager_Base/WL55_Pager_Base.ino 4.5 KB the demo sketch
| |-- WL55_Pager_Field/WL55_Pager_Field.ino 4.4 KB the demo sketch
| |-- TEP Boards for Proteus/hardware/ 1.18 MB the Arduino IDE add-on 1.71.0 (285 files)
|-- Proteus Simulation/
| |-- TEPNET.DLL 2.93 MB copy of the model
| |-- WL55_Pager_Base.hex 37.1 KB the demo sketch (U1)
| |-- WL55_Pager_Field.hex 36.9 KB the demo sketch (U2)
| |-- WL55-LoRa-Farm-Pager.pdsprj 16.0 KB the demo: a two-way LoRa pager
|-- README.txt ~11.5 KB this file
Total: 7.18 MB (unzipped). The source code of the models is not included.
WHAT IS IT?
Proteus 8 has no STM32WL55 model, so this is NOT a real STM32WL55. Our team has put a lot of effort into building this
board ourselves: it is ST's NUCLEO-WL55JC1, the STM32WL Nucleo-64 board for the high band (865 .. 928 MHz) - the white
board with the STM32WL55JC (an Arm Cortex-M4 and a Cortex-M0+ at 48 MHz; a sub-GHz radio for LoRa, (G)FSK, (G)MSK and
BPSK; 256 KB of flash, 64 KB of RAM), the 32 MHz TCXO, the RF matching network and the SMA socket for the antenna, the
STLINK-V3E debugger with its micro-USB, the MIPI debug connector, three user LEDs (LD1 blue, LD2 green, LD3 red),
three user buttons (B1 .. B3), RESET and the Arduino Uno V3 headers - drawn compact, and it runs YOUR Arduino sketch in
Proteus:
* You write a normal sketch with the STM32duino board's names (D0 .. D15, A0 .. A5, LED1 / LED2 / LED3 = LED_BLUE /
LED_GREEN / LED_RED, B1_BTN / B2_BTN / B3_BTN) and compile it in the Arduino IDE with our board package "TEP Boards
for Proteus" 1.71.0 (in Arduino Code - see INSTALLATION).
* LoRa works through the LoRa library of the board package (begin, beginPacket / print / endPacket, parsePacket /
read, packetRssi, packetSnr, setTxPower, setSpreadingFactor ...). Every TEP LoRa board in the same simulation hears
it; the property LORADIST sets the distance, and the signal (RSSI, SNR) follows it.
* LD1 / LD2 / LD3 light when HIGH (LED_BUILTIN is LED1). B1 .. B3 read LOW while you hold them: click a button on the
board in the running simulation.
TEP additions: the STLINK's USB opens the serial monitor (the same window as our TEP Serial Monitor Advance).
Limits (say them before you start): LoRa only (no LoRaWAN network server in a simulation; (G)FSK, (G)MSK and BPSK are
not modelled). Your sketch is one program (the two cores are not split). The ST morpho headers are left out of the
drawing; the MIPI connector is drawn, not modelled. Your sketch gets 8 KB of RAM in the simulation (the real one:
64 KB), about 256 KB of flash, and int is 16 bits in the simulation (use long for big numbers). See MODEL SCOPE AND
LIMITS.
ONE DEVICE (search "NUCLEO-WL55" in Pick Devices):
NUCLEO-WL55JC1 "NUCLEO-WL55JC1" V1.0 (Microprocessor ICs > LoRa Boards), prefix U, model TEPNET.DLL.
Its TEP window has no Windows title bar: the serial monitor (the STLINK's USB, 115200 baud: Monitor, Plotter and
Board tabs).
The same TEPNET.DLL also runs our other sketch boards; it replaces any older TEPNET.DLL (keep only this newest one in
MODELS).
TEST STATUS
V1.0: verified in Proteus 8.5 on 17 Nov 2026 with the demo project as shipped. What the Proteus run showed:
* WL55-LoRa-Farm-Pager: both monitors "LoRa ready on 868 MHz"; U1 (the base) "B1 = come back, B2 = are you OK?, B3 =
storm warning", U2 (the pager) "B1 = on my way, B2 = all OK, B3 = need help".
* U1 B2: "Message 1: Are you OK?", LD2 on both boards; U2 "Message 1: Are you OK? (-116 dBm, SNR 0.8 dB)"; U1 "The
pager got message 1". U2 B2: U1 "Worker: All OK", U2 "The base got the answer", the pager's LD2 off.
* U1 B3: the storm warning, LD3 on both; U2 B1: "Worker: On my way", LD1 on the base. U1 B1: "Message 3: Come back to
the house", LD1 on both; U2 B3: "Worker: Need help!", LD3 on the base.
* about 13 s of simulation, no errors, no repeats needed at 2 km (LORADIST 2 km), with both monitors open.
INSTALLATION (about 3 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" to the LIBRARY folder of Proteus, for example:
C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
(on some PCs: C:\ProgramData\Labcenter Electronics\Proteus 8 Professional\LIBRARY). TEPWL55.LIB is the board.
3. Copy TEPNET.DLL from "Proteus Model Files" to the MODELS folder (...\Proteus 8 Professional\MODELS) - replace an
older TEPNET.DLL (this one is the first that knows this board).
4. Delete TEPWL55.IDX from the LIBRARY folder if it is there.
5. The Arduino IDE (only to compile your own sketches - the demo has its HEX files): copy the folder
"Arduino Code\TEP Boards for Proteus\hardware" into your sketchbook folder (normally Documents\Arduino), so that
Documents\Arduino\hardware\tep\avr\boards.txt exists (replace an older copy); restart the IDE. The Arduino AVR Boards
platform must be installed (it comes with IDE 1.8.x; in IDE 2.x install "Arduino AVR Boards" from the Boards
Manager once).
Tools > Board > TEP Boards for Proteus > ST NUCLEO-WL55JC1 (TEP Proteus). LoRa is in the board package.
6. Start Proteus. In Pick Devices (P) search "NUCLEO-WL55".
RUN THE DEMO
Keep the .hex files and TEPNET.DLL beside the project in "Proteus Simulation".
WL55-LoRa-Farm-Pager.pdsprj - two NUCLEO-WL55JC1 boards 2 km apart (LORADIST 2 km): U1 (left, WL55_Pager_Base.hex) is
the farmhouse base, U2 (right, WL55_Pager_Field.hex) is the worker's pager. No wires: LoRa joins them, the buttons and
the lamps are on the boards.
Press Run. Both monitors print "LoRa ready on 868 MHz". Click B2 on U1: the base sends "Are you OK?", LD2 lights on both
boards and the base prints "The pager got message 1" with the signal. Click B2 on U2: the base prints "Worker: All OK".
B1 / B2 / B3 on the base: come back / are you OK? / storm warning (LD1 / LD2 / LD3); on the pager: on my way / all OK /
need help (the base lights LD1 / LD2 / LD3). Each side repeats a packet up to 3 times until the other confirms it.
Closed a window? The STLINK's USB opens the monitor.
THE PINS (the label on the board, the core's number, what it can do in the simulation)
D0 .. D13 0 .. 13 GPIO, PWM (analogWrite), interrupt; D0 / D1 Serial1 RX / TX; D10 .. D13 SPI (SS, MOSI,
MISO, SCK)
SDA, SCL 14, 15 D14 / D15: Wire, the I2C bus
A0 .. A5 16 .. 21 analogRead 0 .. 1023 for 0 .. 3.3 V, or GPIO
3V3, 5V, GND, RESET 3.3 V (the logic), 5 V, ground, the board's reset; AREF, VIN drawn, not modelled
LED1 / LED2 / LED3 (22 / 23 / 24) are LD1 blue / LD2 green / LD3 red, lit when HIGH (also LED_BLUE / LED_GREEN /
LED_RED; LED_BUILTIN is LED1). B1_BTN / B2_BTN / B3_BTN (25 / 26 / 27) are B1 / B2 / B3, LOW when pressed (pinMode
INPUT_PULLUP); USER_BTN is B1_BTN. Serial is the STLINK's virtual COM port: the board's built-in monitor. The radio is
inside the board (not on the header pins). (The STM32duino board numbers the LEDs and buttons differently; use the
names.)
PROPERTIES (double-click the part > Edit Properties)
PROGRAM the sketch's HEX (Arduino IDE: Sketch > Export Compiled Binary, board ST NUCLEO-WL55JC1 (TEP Proteus))
MONITOR YES = the built-in serial monitor on Serial; BAUD its speed (115200, or AUTO)
AUTOOPEN YES = the monitor window opens at Run (the demo: YES)
LORADIST the LoRa distance to the other boards: 10 m, 100 m, 1 km, 2 km, 5 km, 10 km, 15 km, 20 km (demo: 2 km)
TROUBLESHOOTING
* "LoRa failed": the sketch must include LoRa.h and call LoRa.begin(868E6) (or 915E6) once in setup().
* The other board hears nothing: both need the same frequency, spreading factor and bandwidth; at 15 km or more the
packets may be lost - try a smaller LORADIST, or a higher spreading factor.
* Two boards answer at the same moment and one packet is lost: wait about 40 ms after a packet before you reply, and
repeat a packet until the other side confirms it (as the demo does).
* A button seems dead: use pinMode(B1_BTN, INPUT_PULLUP) and act on the change to LOW.
* An integer goes wrong above 32767: int is 16 bits in the simulation - use long.
BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot and the Serial Monitor text:
https://www.theengineeringprojects.com/forum
LICENCES AND THIRD-PARTY NOTES
* The board model (TEPNET.DLL) and the symbols and artwork (TEPWL55.LIB) are made by The Engineering Projects. The
source code of the models is not included.
* TEP Boards for Proteus (Arduino Code): its core, the variants and the EEPROM, SPI and Wire libraries are modified
copies of the Arduino AVR core 1.8.6 - GNU Lesser General Public License 2.1 (LGPL 2.1, the text:
LICENSE-LGPL-2.1.txt); its LoRa library (the API of Sandeep Mistry's arduino-LoRa) and the others and our core files
are MIT (LICENSE-MIT.txt).
* Proteus is a product of Labcenter Electronics and is not included. STM32, Nucleo and ST are names of
STMicroelectronics, Arduino of Arduino, LoRa of Semtech. This library is not made or endorsed by them or by
Labcenter.
REBUILDING THE FIRMWARE (OPTIONAL)
The HEX files are supplied. Install TEP Boards for Proteus (INSTALLATION step 5), open Arduino Code\WL55_Pager_Base (or
WL55_Pager_Field), select ST NUCLEO-WL55JC1 (TEP Proteus) and use Sketch > Export Compiled Binary. For a real board use
the STM32duino core with RadioLib's STM32WLx class (or STM32LoRaWAN for LoRaWAN), or STM32CubeIDE with the STM32CubeWL
package. Its pins work at 3.3 V; never transmit without the antenna on the SMA socket.
MODEL SCOPE AND LIMITS
Modelled: D0 .. D15 and A0 .. A5; digital I/O, analogRead 0 .. 1023, PWM (analogWrite), tone and attachInterrupt
through the board model; Serial (the board's monitor), Serial1, Wire and SPI; LD1 .. LD3, B1 .. B3 and RESET; LoRa
packets to and from the other TEP LoRa boards, with RSSI and SNR from LORADIST.
Not modelled: the STM32WL55 itself and its second core, LoRaWAN, (G)FSK, (G)MSK and BPSK, the MIPI debug connector, the
morpho headers. The simulation runs below real time.
VERSION
TEP NUCLEO-WL55JC1 library V1.0 (Nov 2026). Device NUCLEO-WL55JC1 (TEPWL55.LIB / TEPNET.DLL), TEP Boards for Proteus
1.71.0 (adds this board: LoRa, D0 .. D15, A0 .. A5, LED1 .. LED3, B1_BTN .. B3_BTN).
Demo sketches WL55_Pager_Base and WL55_Pager_Field V1.0.Development1 release
-
V1.0NUCLEO-WL55JC1 Library for Proteus V1.0this page
V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.
Installation10 steps
From the download to a working project, in order. The steps follow what the package contains.
You will need
- Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
- Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
- The compiler named in the tutorialto build the source files into firmware
- Any archive toolWindows, macOS and Linux extract ZIP files on their own
Steps
- 1
Extract the archive
Right-click 42544a4d70e64d389d374e2f758b23d0.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (NUCLEO-WL55JC1-TEP-v1.0) as it is.
- 2
Copy the library files into Proteus
Move TEPWL55.LIB and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.
- 3
Add the simulation model
Copy TEPNET.DLL into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.
- 4
Restart Proteus and place the component
Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.
- 5
Install the Arduino library
In the Arduino IDE choose Sketch → Include Library → Add .ZIP Library and pick the library, or copy its folder into Documents\Arduino\libraries. Restart the IDE to see its examples.
- 6
Open the sketch in the Arduino IDE
Open WL55_Pager_Base.ino, WL55_Pager_Field.ino and eeprom_clear.ino and 18 more, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.
- 7
Build the source code
Open abi.cpp, Arduino.h and binary.h and 52 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.
- 8
Load the HEX file
In Proteus double-click the microcontroller, set Program File to WL55_Pager_Base.hex and WL55_Pager_Field.hex and run the simulation. For real hardware, flash the same file with your programmer.
- 9
Open the example simulation
Open WL55-LoRa-Farm-Pager.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.
- 10
Follow the tutorial
NUCLEO-WL55JC1 Library for Proteus: STM32WL LoRa Pager Simulation explains every connection and setting in order; keep it open beside the files while you build.
FAQs9 questionsContact TEP
How do I download NUCLEO-WL55JC1 Library for Proteus V1.0?
Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.
What is inside the archive?
NUCLEO-WL55JC1 Library for Proteus V1.0 comes as a ZIP archive of 294 files (3.2 MB, 7.2 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code. Open the File Structure tab for the full list of 294 files.
What should I do if the download does not start?
Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.
Is this file free?
Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.
How do I check that the file arrived complete?
Compare its SHA-256 with the one on this page, 880480fefbee6c16fb1c351582650c72b5de553404bb7bbfd16417dfdf590b3f. In PowerShell run Get-FileHash "42544a4d70e64d389d374e2f758b23d0.zip"; on macOS or Linux run shasum -a 256 "42544a4d70e64d389d374e2f758b23d0.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.
Do I need WinRAR to open the ZIP file?
No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.
Where do I put the LIB and IDX files?
Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.
Which Proteus version does the library need?
The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.
How do I get the HEX file into the simulation?
Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.
Members skip the wait. Log in or join TEP.
- 0Total downloads
- 4%Popularity
- ProteusCategory
- 0Comments
- ssyedzainnasirUploaded by
- 19 Nov 2026Uploaded at
880480fefbee6c16fb1c351582650c72b5de553404bb7bbfd16417dfdf590b3f
















Comments
0