Project Files of NUCLEO-WB55RG Library for Proteus: STM32WB BLE Quiz Simulation
e1a4142f8cff469dbfb43c17b73ab54b.zip

NUCLEO-WB55RG Library for Proteus V1.0
NUCLEO-WB55RG Library for Proteus V1.0 comes as a ZIP archive of 293 files (3.2 MB, 7.2 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code.
- LIBProteus library
- DLLProteus model
- DSNProteus simulation
- INOArduino sketch
- LIBArduino library
- HEXHEX firmware
- SRCSource code
Description
NUCLEO-WB55RG-Library-for-Proteus-v1.0.zip with ST's NUCLEO-WB55RG in Proteus (your sketch with D0 .. D15, A0 .. A5, LD1 .. LD3, SW1 .. SW3, Bluetooth LE to a phone and a serial monitor; TEPWB55.LIB, TEPNET.DLL and the TEP Boards for Proteus add-on 1.70.0), the phone library, the quiz buzzer demo with its sketch and a README.
File Structure
1.1 KB7.7 KB11 KB8.5 KB1.5 KB1.7 KB1.9 KB5.7 KB4.9 KB1.1 KB5.8 KB9.6 KB7.2 KB2.5 KB2.1 KB1.9 KB2.1 KB4.4 KB1.1 KB3 KB3 KB1.8 KB2.5 KB3.5 KB149 B2.7 KB2 KB6.4 KB3.2 KB1.3 KB963 B8.6 KB5.9 KB6 KB12 KB1.6 KB1.3 KB14.7 KB4.3 KB6.1 KB20.1 KB8.2 KB2 KB4.5 KB311 B12.8 KB6.7 KB6.1 KB2.2 KB3.4 KB5.9 KB1.5 KB1.6 KB16.6 KB9.7 KB6.9 KB2.1 KB533 B5.7 KB7.4 KB514 B1.7 KB896 B481 B1.4 KB1012 B482 B936 B559 B467 B3.6 KB3.8 KB504 B956 B575 B455 B8.3 KB10.9 KB522 B79 B5.5 KB3.1 KB79 B442 B918 B1.4 KB1.8 KB1 KB1.3 KB1.4 KB1.8 KB1.4 KB5.7 KB502 B463 B5 KB6.5 KB3.4 KB3.4 KB500 B1.6 KB368 B406 B466 B404 B444 B460 B477 B739 B448 B1.3 KB350 B5.7 KB4 KB562 B1.5 KB2 KB550 B7.2 KB4.1 KB371 B4.5 KB3.5 KB492 B390 B478 B6.6 KB2.4 KB479 B5.1 KB1.9 KB1.3 KB1.3 KB750 B1.3 KB490 B2.2 KB1.9 KB498 B1.2 KB1.2 KB487 B5.1 KB4.6 KB371 B1.5 KB1.2 KB478 B6.2 KB3 KB1.5 KB1.7 KB469 B1 KB1.7 KB433 B294 B358 B1.3 KB2.5 KB13.2 KB3.8 KB659 B510 B4.4 KB1.9 KB5.8 KB11 KB835 B518 B6.4 KB2.3 KB29 B436 B9.2 KB4.9 KB439 B4.2 KB1.5 KB9.3 KB7.1 KB4.7 KB2.4 KB388 B5.1 KB893 B667 B1.3 KB5.5 KB2.3 KB1.8 KB468 B882 B530 B791 B487 B894 B2 KB730 B646 B2.6 KB977 B702 B20.6 KB1.8 KB11.8 KB3.2 KB596 B406 B6.3 KB5.7 KB9.3 KB7.7 KB7.7 KB6.1 KB5.8 KB5.9 KB6.4 KB6.4 KB5.3 KB5.6 KB5.7 KB7.9 KB7.7 KB6.5 KB6.3 KB6.2 KB10.3 KB8.5 KB6.6 KB7.6 KB6.7 KB6.1 KB6.7 KB8.3 KB6.2 KB7.2 KB5.9 KB5.6 KB5.7 KB6.7 KB5.9 KB6.2 KB6 KB6 KB6.1 KB6.3 KB6 KB6.1 KB6.2 KB6 KB5.8 KB6.4 KB6.4 KB6.9 KB6 KB6.8 KB7 KB6.4 KB6.5 KB6.6 KB6.5 KB5.6 KB5.9 KB7.5 KB3.8 KB5.4 KB7.7 KB7.1 KB5.8 KB5.9 KB5.9 KB6.9 KB5.7 KB5.9 KB5.5 KB5.5 KB7.1 KB5.2 KB34.5 KB25.9 KB1.3 KB8.5 KB35.7 KB4.8 KB39.5 KB13.1 KB36.4 KB2.9 MB2.9 MB17.3 KB31.5 KB10.8 KBGallery12 images from the tutorialOpen the tutorial
The circuit, the board and the results as they appear in NUCLEO-WB55RG Library for Proteus: STM32WB BLE Quiz Simulation. Open an image for its full size.












README
NUCLEO-WB55RG LIBRARY FOR PROTEUS - V1.0 (YOUR ARDUINO SKETCH, BLUETOOTH LE, THREE LEDS AND THREE BUTTONS)
Designed by The Engineering Projects
www.TheEngineeringProjects.com
IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
https://www.theengineeringprojects.com/2026/11/nucleo-wb55rg-library-for-proteus.html
Report a bug or suggest a feature (our forum):
https://www.theengineeringprojects.com/forum
The demo's phone is our Mobile WiFi Monitor (included) - its article:
https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
Support us (the libraries are free):
https://www.theengineeringprojects.com/donate
FILE STRUCTURE
NUCLEO-WB55RG-TEP-v1.0/
|-- Proteus Library Files/
| |-- TEPLAPTOP.LIB 39.5 KB the laptop (demo), to LIBRARY
| |-- TEPMOBILE.LIB 13.1 KB the phone (demo), to LIBRARY
| |-- TEPWB55.LIB 36.4 KB the NUCLEO-WB55RG, to LIBRARY
|-- Proteus Model Files/
| |-- TEPNET.DLL 2.92 MB the board + monitors + network, to MODELS
|-- Arduino Code/
| |-- WB55_Quiz_Buzzer/WB55_Quiz_Buzzer.ino 4.8 KB the demo sketch
| |-- TEP Boards for Proteus/hardware/ 1.18 MB the Arduino IDE add-on 1.70.0 (284 files)
|-- Proteus Simulation/
| |-- TEPNET.DLL 2.92 MB copy of the model
| |-- WB55_Quiz_Buzzer.hex 31.5 KB the demo sketch (U1)
| |-- WB55-BLE-Quiz-Buzzer.pdsprj 17.3 KB the demo: a Bluetooth LE quiz buzzer
|-- README.txt ~10.8 KB this file
Total: 7.18 MB (unzipped). The source code of the models is not included.
WHAT IS IT?
Proteus 8 has no STM32WB55 model, so this is NOT a real STM32WB55. Our team has put a lot of effort into building this
board ourselves: it is ST's NUCLEO-WB55RG, the Nucleo-68 board of the P-NUCLEO-WB55 pack - the white board with the
STM32WB55RG (an Arm Cortex-M4 at 64 MHz for your program and a Cortex-M0+ for the radio; Bluetooth LE 5 and IEEE
802.15.4 for Thread and Zigbee; 1 MB of flash, 256 KB of RAM), its printed 2.4 GHz antenna, the ST-LINK debugger with
its micro-USB, a user USB port, three user LEDs (LD1 blue, LD2 green, LD3 red), three user buttons (SW1 .. SW3), RESET
and the Arduino Uno V3 headers - drawn compact, and it runs YOUR Arduino sketch in Proteus:
* You write a normal sketch with the STM32duino board's names (D0 .. D15, A0 .. A5, LED_BLUE / LED_GREEN / LED_RED,
USER_BTN / USER_BTN2 / USER_BTN3) and compile it in the Arduino IDE with our board package "TEP Boards for Proteus"
1.70.0 (in Arduino Code - see INSTALLATION).
* Bluetooth LE works through ArduinoBLE (the board as a peripheral, the phone of our Mobile WiFi Monitor as the
central: it scans, connects, reads, writes and gets notifications).
* LD1 / LD2 / LD3 light when HIGH (LED_BUILTIN is LED_BLUE). SW1 .. SW3 read LOW while you hold them: click a button
on the board in the running simulation.
TEP additions: the ST-LINK's USB opens the serial monitor (the same window as our TEP Serial Monitor Advance).
Limits (say them before you start): Bluetooth LE: the board is a peripheral only; Thread and Zigbee are not modelled.
Your sketch is one program (the two cores are not split). The ST morpho headers are left out of the drawing; the user
USB and the coin-cell holder are drawn, not modelled. Your sketch gets 8 KB of RAM in the simulation (the real one:
256 KB), about 256 KB of flash, and int is 16 bits in the simulation (use long for big numbers). See MODEL SCOPE AND
LIMITS.
ONE DEVICE (search "NUCLEO-WB55" in Pick Devices):
NUCLEO-WB55RG "NUCLEO-WB55RG" V1.0 (Microprocessor ICs > Bluetooth Boards), prefix U, model TEPNET.DLL.
Its TEP window has no Windows title bar: the serial monitor (the ST-LINK's USB, 115200 baud: Monitor, Plotter and
Board tabs).
The same TEPNET.DLL also runs our other sketch boards and the phone; it replaces any older TEPNET.DLL (keep only this
newest one in MODELS).
TEST STATUS
V1.0: verified in Proteus 8.5 on 17 Nov 2026 with the demo project as shipped. What the Proteus run showed:
* WB55-BLE-Quiz-Buzzer: "Advertising as "WB55 Quiz", address 00:80:E1:26:00:01", "SW1 = BLUE, SW2 = GREEN, SW3 =
RED", "Ready for question 1".
* The phone's Bluetooth app, SCAN, Connect: "Quiz master connected"; the phone showed Winner, Question and the three
scores at 0.
* SW1: "Question 1: BLUE buzzed first! Score BLUE 1 GREEN 0 RED 0", LD1 on; SW3 right after it: "RED pressed too
late"; after 3 s "Ready for question 2", LD1 off; the phone showed the winner BLUE and the score.
* SW3: RED first (LD3), SW2: GREEN first (LD2), SW1: BLUE first again: "Score BLUE 2 GREEN 1 RED 1", then "Ready for
question 5"; the phone showed the same scores.
* about 26 s of simulation, no errors, with the phone and the monitor open.
INSTALLATION (about 3 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" to the LIBRARY folder of Proteus, for example:
C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
(on some PCs: C:\ProgramData\Labcenter Electronics\Proteus 8 Professional\LIBRARY). TEPWB55.LIB is the board;
TEPMOBILE.LIB and TEPLAPTOP.LIB are the phone and the laptop.
3. Copy TEPNET.DLL from "Proteus Model Files" to the MODELS folder (...\Proteus 8 Professional\MODELS) - replace an
older TEPNET.DLL (this one is the first that knows this board).
4. Delete TEPWB55.IDX from the LIBRARY folder if it is there.
5. The Arduino IDE (only to compile your own sketches - the demo has its HEX file): copy the folder
"Arduino Code\TEP Boards for Proteus\hardware" into your sketchbook folder (normally Documents\Arduino), so that
Documents\Arduino\hardware\tep\avr\boards.txt exists (replace an older copy); restart the IDE. The Arduino AVR Boards
platform must be installed (it comes with IDE 1.8.x; in IDE 2.x install "Arduino AVR Boards" from the Boards
Manager once).
Tools > Board > TEP Boards for Proteus > ST NUCLEO-WB55RG (TEP Proteus). ArduinoBLE is in the board package.
6. Start Proteus. In Pick Devices (P) search "NUCLEO-WB55".
RUN THE DEMO
Keep the .hex file and TEPNET.DLL beside the project in "Proteus Simulation".
WB55-BLE-Quiz-Buzzer.pdsprj - U1 the NUCLEO-WB55RG (WB55_Quiz_Buzzer.hex) is a three-player quiz buzzer; MOB1 = the quiz
master's phone (Mobile WiFi Monitor), whose Bluetooth app connects to it. No wires: the buttons and the lamps are on
the board.
Press Run. The monitor prints "Advertising as "WB55 Quiz"" and "Ready for question 1". In the phone's Bluetooth app
press SCAN and connect to "WB55 Quiz". Click SW1: "BLUE buzzed first!", LD1 on; a press of another button within 3 s
is "too late". After 3 s: "Ready for question 2". SW2 is GREEN (LD2), SW3 is RED (LD3). The phone shows the winner,
the question and the three scores.
Closed a window? The ST-LINK's USB opens the monitor, a click on the phone's screen the phone.
THE PINS (the label on the board, the core's number, what it can do in the simulation)
D0 .. D13 0 .. 13 GPIO, PWM (analogWrite), interrupt; D0 / D1 Serial1 RX / TX; D10 .. D13 SPI (SS, MOSI,
MISO, SCK)
SDA, SCL 14, 15 D14 / D15: Wire, the I2C bus
A0 .. A5 16 .. 21 analogRead 0 .. 1023 for 0 .. 3.3 V, or GPIO
3V3, 5V, GND, RESET 3.3 V (the logic), 5 V, ground, the board's reset; AREF, VIN drawn, not modelled
LED_BLUE / LED_GREEN / LED_RED (22 / 23 / 24) are LD1 / LD2 / LD3, lit when HIGH; LED_BUILTIN is LED_BLUE. USER_BTN /
USER_BTN2 / USER_BTN3 (25 / 26 / 27) are SW1 / SW2 / SW3, LOW when pressed (pinMode INPUT_PULLUP); BTN_BUILTIN is
USER_BTN. Serial is the ST-LINK's virtual COM port: the board's built-in monitor. (The STM32duino board numbers the
LEDs and buttons differently; use the names.)
PROPERTIES (double-click the part > Edit Properties)
PROGRAM the sketch's HEX (Arduino IDE: Sketch > Export Compiled Binary, board ST NUCLEO-WB55RG (TEP Proteus))
MONITOR YES = the built-in serial monitor on Serial; BAUD its speed (115200, or AUTO)
AUTOOPEN YES = the monitor window opens at Run (the demo: YES)
TROUBLESHOOTING
* The phone finds nothing: press SCAN after "Advertising as" is printed; the sketch must call BLE.advertise().
* A button seems dead: use pinMode(USER_BTN, INPUT_PULLUP) and act on the change to LOW.
* The LEDs look inverted: on this board they light when the pin is HIGH.
* An integer goes wrong above 32767: int is 16 bits in the simulation - use long.
BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot and the Serial Monitor text:
https://www.theengineeringprojects.com/forum
LICENCES AND THIRD-PARTY NOTES
* The board model (TEPNET.DLL) and the symbols and artwork (TEPWB55.LIB) are made by The Engineering Projects. The
source code of the models is not included.
* TEP Boards for Proteus (Arduino Code): its core, the variants and the EEPROM, SPI and Wire libraries are modified
copies of the Arduino AVR core 1.8.6 - GNU Lesser General Public License 2.1 (LGPL 2.1, the text:
LICENSE-LGPL-2.1.txt); its ArduinoBLE and the others and our core files are MIT (LICENSE-MIT.txt).
* Proteus is a product of Labcenter Electronics and is not included. STM32, Nucleo and ST are names of
STMicroelectronics, Arduino of Arduino. The Bluetooth word mark belongs to Bluetooth SIG. This library is not made or
endorsed by them or by Labcenter.
REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied. Install TEP Boards for Proteus (INSTALLATION step 5), open Arduino Code\WB55_Quiz_Buzzer,
select ST NUCLEO-WB55RG (TEP Proteus) and use Sketch > Export Compiled Binary. For a real board use the STM32duino core
with STM32duinoBLE, or STM32CubeIDE with the STM32WB package (the radio core needs ST's wireless stack). Its pins work
at 3.3 V.
MODEL SCOPE AND LIMITS
Modelled: D0 .. D15 and A0 .. A5; digital I/O, analogRead 0 .. 1023, PWM (analogWrite), tone and attachInterrupt
through the board model; Serial (the board's monitor), Serial1, Wire and SPI; LD1 .. LD3, SW1 .. SW3 and RESET;
Bluetooth LE as a peripheral.
Not modelled: the STM32WB55 itself and its radio core, Thread and Zigbee, the user USB, the coin-cell power, the morpho
headers, the board as a Bluetooth central. The simulation runs below real time.
VERSION
TEP NUCLEO-WB55RG library V1.0 (Nov 2026). Device NUCLEO-WB55RG (TEPWB55.LIB / TEPNET.DLL), TEP Boards for Proteus
1.70.0 (adds this board: Bluetooth LE, D0 .. D15, A0 .. A5, LED_BLUE / LED_GREEN / LED_RED, USER_BTN .. USER_BTN3).
Demo sketch WB55_Quiz_Buzzer V1.0. Demo part: MOBILE WIFI MONITOR.Development1 release
-
V1.0NUCLEO-WB55RG Library for Proteus V1.0this page
V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.
Installation10 steps
From the download to a working project, in order. The steps follow what the package contains.
You will need
- Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
- Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
- The compiler named in the tutorialto build the source files into firmware
- Any archive toolWindows, macOS and Linux extract ZIP files on their own
Steps
- 1
Extract the archive
Right-click e1a4142f8cff469dbfb43c17b73ab54b.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (NUCLEO-WB55RG-TEP-v1.0) as it is.
- 2
Copy the library files into Proteus
Move TEPLAPTOP.LIB, TEPMOBILE.LIB and TEPWB55.LIB and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.
- 3
Add the simulation model
Copy TEPNET.DLL into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.
- 4
Restart Proteus and place the component
Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.
- 5
Install the Arduino library
In the Arduino IDE choose Sketch → Include Library → Add .ZIP Library and pick the library, or copy its folder into Documents\Arduino\libraries. Restart the IDE to see its examples.
- 6
Open the sketch in the Arduino IDE
Open WB55_Quiz_Buzzer.ino, eeprom_clear.ino and eeprom_crc.ino and 17 more, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.
- 7
Build the source code
Open abi.cpp, Arduino.h and binary.h and 52 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.
- 8
Load the HEX file
In Proteus double-click the microcontroller, set Program File to WB55_Quiz_Buzzer.hex and run the simulation. For real hardware, flash the same file with your programmer.
- 9
Open the example simulation
Open WB55-BLE-Quiz-Buzzer.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.
- 10
Follow the tutorial
NUCLEO-WB55RG Library for Proteus: STM32WB BLE Quiz Simulation explains every connection and setting in order; keep it open beside the files while you build.
FAQs9 questionsContact TEP
How do I download NUCLEO-WB55RG Library for Proteus V1.0?
Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.
What is inside the archive?
NUCLEO-WB55RG Library for Proteus V1.0 comes as a ZIP archive of 293 files (3.2 MB, 7.2 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code. Open the File Structure tab for the full list of 293 files.
What should I do if the download does not start?
Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.
Is this file free?
Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.
How do I check that the file arrived complete?
Compare its SHA-256 with the one on this page, 8fee413b6deea8f89286f1e475462834b1569b4451f4c8effa03b5de63b64f7f. In PowerShell run Get-FileHash "e1a4142f8cff469dbfb43c17b73ab54b.zip"; on macOS or Linux run shasum -a 256 "e1a4142f8cff469dbfb43c17b73ab54b.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.
Do I need WinRAR to open the ZIP file?
No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.
Where do I put the LIB and IDX files?
Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.
Which Proteus version does the library need?
The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.
How do I get the HEX file into the simulation?
Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.
Members skip the wait. Log in or join TEP.
- 0Total downloads
- 4%Popularity
- ProteusCategory
- 0Comments
- ssyedzainnasirUploaded by
- 19 Nov 2026Uploaded at
8fee413b6deea8f89286f1e475462834b1569b4451f4c8effa03b5de63b64f7f
















Comments
0