Project Files of NUCLEO-H743ZI2 Library for Proteus: STM32H7 Ethernet Simulation
205129f8594d421483ddf389f5ae8715.zip

NUCLEO-H743ZI2 Library for Proteus V1.0
NUCLEO-H743ZI2 Library for Proteus V1.0 comes as a ZIP archive of 302 files (3.6 MB, 8.1 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code.
- LIBProteus library
- DLLProteus model
- DSNProteus simulation
- INOArduino sketch
- LIBArduino library
- HEXHEX firmware
- SRCSource code
Description
NUCLEO-H743ZI2-Library-for-Proteus-v1.0.zip with ST's NUCLEO-H743ZI2 in Proteus (your sketch with D0 .. D15, A0 .. A5, LD1 .. LD3, USER, Ethernet by STM32Ethernet to the router and a serial monitor; TEPH743.LIB, TEPNET.DLL and the TEP Boards for Proteus add-on 1.72.0), the BME280 and phone libraries, the server room demo with its sketch and a README.
File Structure
6.3 KB1.1 KB7.7 KB11 KB8.5 KB1.5 KB1.7 KB1.9 KB5.7 KB4.9 KB1.1 KB5.8 KB9.6 KB7.2 KB2.5 KB2.1 KB1.9 KB2.1 KB4.4 KB1.1 KB3 KB3 KB1.8 KB2.5 KB3.5 KB149 B2.7 KB2 KB6.4 KB3.2 KB1.3 KB963 B8.6 KB5.9 KB6 KB12 KB1.6 KB1.3 KB14.7 KB4.3 KB6.1 KB20.1 KB8.2 KB2 KB4.5 KB311 B12.8 KB6.7 KB6.1 KB2.2 KB3.4 KB5.9 KB1.5 KB1.6 KB16.6 KB9.7 KB6.9 KB2.1 KB533 B5.7 KB7.4 KB514 B1.7 KB896 B481 B1.4 KB1012 B482 B936 B559 B467 B3.6 KB3.8 KB504 B956 B575 B455 B8.3 KB10.9 KB522 B79 B5.5 KB3.1 KB79 B442 B918 B1.4 KB1.8 KB1 KB1.3 KB1.4 KB1.8 KB1.4 KB5.7 KB502 B463 B5 KB6.5 KB3.4 KB3.4 KB500 B1.6 KB368 B406 B466 B404 B444 B460 B477 B739 B448 B1.3 KB350 B5.7 KB4 KB562 B1.5 KB2 KB550 B7.2 KB4.1 KB371 B4.5 KB3.5 KB492 B390 B478 B6.6 KB2.4 KB479 B5.1 KB1.9 KB1.3 KB1.3 KB750 B1.3 KB490 B2.2 KB1.9 KB498 B1.2 KB1.2 KB487 B5.1 KB4.6 KB371 B1.5 KB1.2 KB478 B6.2 KB3 KB1.5 KB1.7 KB469 B1 KB1.7 KB433 B294 B358 B1.3 KB2.5 KB13.2 KB3.8 KB659 B510 B4.4 KB1.9 KB5.8 KB11 KB835 B518 B308 B1.3 KB3.3 KB568 B6.4 KB2.3 KB29 B436 B9.2 KB4.9 KB439 B4.2 KB1.5 KB9.3 KB7.1 KB4.7 KB2.4 KB388 B5.1 KB893 B667 B1.3 KB5.5 KB2.3 KB1.8 KB468 B882 B530 B791 B487 B894 B2 KB730 B646 B2.6 KB977 B702 B20.6 KB1.8 KB11.8 KB3.2 KB596 B406 B6.3 KB5.7 KB9.3 KB7.7 KB7.7 KB6.1 KB5.8 KB5.9 KB6.4 KB6.4 KB5.3 KB5.6 KB5.7 KB7.9 KB7.7 KB6.5 KB6.3 KB6.2 KB10.3 KB8.5 KB6.6 KB7.6 KB6.7 KB6.1 KB6.7 KB8.3 KB6.2 KB7.2 KB5.9 KB5.6 KB5.7 KB6.7 KB5.9 KB6.2 KB6 KB6 KB6.1 KB6.3 KB6 KB6.1 KB6.2 KB6 KB5.8 KB6.4 KB6.4 KB6.9 KB6 KB6.8 KB7 KB6.3 KB6.4 KB6.5 KB6.5 KB6.6 KB6.5 KB5.6 KB5.9 KB7.5 KB3.8 KB5.4 KB7.7 KB7.1 KB5.8 KB5.9 KB5.9 KB6.9 KB5.7 KB5.9 KB5.5 KB5.5 KB7.1 KB5.2 KB35.4 KB25.9 KB1.3 KB8.5 KB35.9 KB89.4 KB37.7 KB39.5 KB13.1 KB381 KB2.9 MB21.6 KB63.2 KB381 KB2.9 MB11.7 KBGallery12 images from the tutorialOpen the tutorial
The circuit, the board and the results as they appear in NUCLEO-H743ZI2 Library for Proteus: STM32H7 Ethernet Simulation. Open an image for its full size.












README
NUCLEO-H743ZI2 LIBRARY FOR PROTEUS - V1.0 (YOUR ARDUINO SKETCH, ETHERNET, THREE LEDS AND THE USER BUTTON)
Designed by The Engineering Projects
www.TheEngineeringProjects.com
IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
https://www.theengineeringprojects.com/2026/11/nucleo-h743zi2-library-for-proteus.html
Report a bug or suggest a feature (our forum):
https://www.theengineeringprojects.com/forum
The demo's phone is our Mobile WiFi Monitor (included) - its article:
https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
Support us (the libraries are free):
https://www.theengineeringprojects.com/donate
FILE STRUCTURE
NUCLEO-H743ZI2-TEP-v1.0/
|-- Proteus Library Files/
| |-- TEPBME280.LIB 89.4 KB the BME280 (demo), to LIBRARY
| |-- TEPH743.LIB 37.7 KB the NUCLEO-H743ZI2, to LIBRARY
| |-- TEPLAPTOP.LIB 39.5 KB the laptop (demo), to LIBRARY
| |-- TEPMOBILE.LIB 13.1 KB the phone (demo), to LIBRARY
|-- Proteus Model Files/
| |-- TEPBME280.DLL 381.0 KB the BME280, to MODELS
| |-- TEPNET.DLL 2.93 MB the board + monitors + network, to MODELS
|-- Arduino Code/
| |-- H743_Server_Room/H743_Server_Room.ino 6.3 KB the demo sketch
| |-- TEP Boards for Proteus/hardware/ 1.20 MB the Arduino IDE add-on 1.72.0 (290 files)
|-- Proteus Simulation/
| |-- H743_Server_Room.hex 63.2 KB the demo sketch (U1)
| |-- H743-Ethernet-Server-Room.pdsprj 21.6 KB the demo: an Ethernet server room monitor
| |-- TEPBME280.DLL 381.0 KB copy of the model
| |-- TEPNET.DLL 2.93 MB copy of the model
|-- README.txt ~11.4 KB this file
Total: 8.08 MB (unzipped). The source code of the models is not included.
WHAT IS IT?
Proteus 8 has no STM32H743 model, so this is NOT a real STM32H743. Our team has put a lot of effort into building this
board ourselves: it is ST's NUCLEO-H743ZI2, the STM32H7 Nucleo-144 board - the white board with the STM32H743ZI (an Arm
Cortex-M7 at 480 MHz; 2 MB of flash, 1 MB of RAM; LQFP144), the LAN8742A Ethernet PHY and its RJ45 jack, the STLINK-V3E
debugger with its micro-USB, the user USB, three user LEDs (LD1 green, LD2 yellow, LD3 red), the USER button (B1) and
RESET, and the Arduino Uno V3 part of the Zio headers - drawn compact, and it runs YOUR Arduino sketch in Proteus:
* You write a normal sketch with the STM32duino board's names (D0 .. D15, A0 .. A5, LED_GREEN / LED_YELLOW / LED_RED,
USER_BTN) and compile it in the Arduino IDE with our board package "TEP Boards for Proteus" 1.72.0 (in Arduino Code
- see INSTALLATION).
* Ethernet works through STM32Ethernet, as on the real board (Ethernet.begin() with DHCP or a fixed address,
EthernetServer, EthernetClient, EthernetUDP, Ethernet.linkStatus()). The board joins the router's LAN by its cable:
the phone of our Mobile WiFi Monitor (on the router's Wi-Fi) opens the board's pages.
* A click on the RJ45 jack pulls the cable out or plugs it in (the jack's LINK / ACT LEDs follow it).
* LD1 / LD2 / LD3 light when HIGH (LED_BUILTIN is LED_GREEN). USER_BTN reads HIGH while you hold B1 (the board pulls
it down, as the real one does): click it on the board in the running simulation.
TEP additions: the STLINK's USB opens the serial monitor (the same window as our TEP Serial Monitor Advance).
Limits (say them before you start): Ethernet: IPv4, TCP and UDP to the TEP network (the router, the phone, the other
boards); the MAC address you pass is not used (the board has its own). The other Zio and the morpho headers are left
out of the drawing; the user USB is drawn, not modelled. Your sketch gets 8 KB of RAM in the simulation (the real one:
1 MB), about 256 KB of flash, and int is 16 bits in the simulation (use long for big numbers). See MODEL SCOPE AND
LIMITS.
ONE DEVICE (search "NUCLEO-H743" in Pick Devices):
NUCLEO-H743ZI2 "NUCLEO-H743ZI2" V1.0 (Microprocessor ICs > Ethernet Boards), prefix U, model TEPNET.DLL.
Its TEP window has no Windows title bar: the serial monitor (the STLINK's USB, 115200 baud: Monitor, Plotter and
Board tabs).
The same TEPNET.DLL also runs our other sketch boards and the phone; it replaces any older TEPNET.DLL (keep only this
newest one in MODELS).
TEST STATUS
V1.0: verified in Proteus 8.5 on 17 Nov 2026 with the demo project as shipped. What the Proteus run showed:
* H743-Ethernet-Server-Room: "Ethernet up, IP 192.168.1.60", "Dashboard: http://192.168.1.60/", "Rack 24.0 C 45 % OK",
LD1 on; the jack's LINK / ACT lit; the phone's browser, Go: the dashboard "Server Room - Rack 1", OK, no alarm.
* The BME280's window at 30 C: ">> Level WARM, 30.0 C", LD2 on; at 32.5 C: ">> ALARM: the rack is HOT, 32.5 C", LD3 on;
the page after Reload: "Alarm: ACTIVE"; USER (B1): ">> Alarm acknowledged by the USER button", the page: acknowledged.
* Back to 25 C: ">> The alarm is over", ">> Level OK, 25.0 C", LD1 on; HOT again and the page's ACK link: ">> Alarm
acknowledged by the web page".
* about 30 s of simulation, no errors, with the BME280 window, the phone and the monitor open.
INSTALLATION (about 3 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" to the LIBRARY folder of Proteus, for example:
C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
(on some PCs: C:\ProgramData\Labcenter Electronics\Proteus 8 Professional\LIBRARY). TEPH743.LIB is the board;
TEPBME280.LIB is the demo's sensor; TEPMOBILE.LIB and TEPLAPTOP.LIB are the phone and the laptop.
3. Copy the DLLs from "Proteus Model Files" to the MODELS folder (...\Proteus 8 Professional\MODELS) - replace an
older TEPNET.DLL (this one is the first that knows this board).
4. Delete TEPH743.IDX from the LIBRARY folder if it is there.
5. The Arduino IDE (only to compile your own sketches - the demo has its HEX file): copy the folder
"Arduino Code\TEP Boards for Proteus\hardware" into your sketchbook folder (normally Documents\Arduino), so that
Documents\Arduino\hardware\tep\avr\boards.txt exists (replace an older copy); restart the IDE. The Arduino AVR Boards
platform must be installed (it comes with IDE 1.8.x; in IDE 2.x install "Arduino AVR Boards" from the Boards
Manager once).
Tools > Board > TEP Boards for Proteus > ST NUCLEO-H743ZI2 (TEP Proteus). STM32Ethernet is in the board package; the
demo also needs Adafruit BME280 and Adafruit Unified Sensor (Library Manager).
6. Start Proteus. In Pick Devices (P) search "NUCLEO-H743".
RUN THE DEMO
Keep the .hex file and the DLLs beside the project in "Proteus Simulation".
H743-Ethernet-Server-Room.pdsprj - U1 the NUCLEO-H743ZI2 (H743_Server_Room.hex) watches a server rack: U2 = BME280 on
SDA / SCL (D14 / D15); MOB1 = the phone (Mobile WiFi Monitor), its browser's home page is the board's dashboard.
Press Run. The monitor prints "Ethernet up, IP 192.168.1.60" and "Dashboard: http://192.168.1.60/". LD1 (green) is on:
the rack is OK. On the phone press Go: the dashboard. In the BME280's window click the temperature track: 28 C or more
is WARM (LD2 yellow), 32 C or more is HOT (LD3 red, the alarm). Click USER (B1) or the page's ACK link: "Alarm
acknowledged". Below 28 C again: "The alarm is over". A click on the RJ45 jack: "Ethernet cable out!".
Closed a window? The STLINK's USB opens the monitor, a click on the phone's screen the phone.
THE PINS (the label on the board, the core's number, what it can do in the simulation)
D0 .. D13 0 .. 13 GPIO, PWM (analogWrite), interrupt; D0 / D1 Serial1 RX / TX; D10 .. D13 SPI (SS, MOSI,
MISO, SCK)
SDA, SCL 14, 15 D14 / D15: Wire, the I2C bus
A0 .. A5 16 .. 21 analogRead 0 .. 1023 for 0 .. 3.3 V, or GPIO
3V3, 5V, GND, RESET 3.3 V (the logic), 5 V, ground, the board's reset; AREF, VIN drawn, not modelled
LED_GREEN / LED_YELLOW / LED_RED (22 / 23 / 24) are LD1 / LD2 / LD3, lit when HIGH; LED_BUILTIN is LED_GREEN. USER_BTN
(25) is B1, HIGH while pressed (pinMode INPUT: the board pulls it down). Serial is the STLINK's virtual COM port: the
board's built-in monitor. The Ethernet PHY is inside the board (not on the header pins). (The STM32duino board numbers
the LEDs and the button differently; use the names.)
PROPERTIES (double-click the part > Edit Properties)
PROGRAM the sketch's HEX (Arduino IDE: Sketch > Export Compiled Binary, board ST NUCLEO-H743ZI2 (TEP Proteus))
MONITOR YES = the built-in serial monitor on Serial; BAUD its speed (115200, or AUTO)
AUTOOPEN YES = the monitor window opens at Run (the demo: YES)
CABLE IN = the Ethernet cable is plugged in at Run, OUT = not (a click on the jack changes it while running)
TROUBLESHOOTING
* The phone shows nothing: press Go after "Dashboard:" is printed; the sketch must call server.begin().
* "No Ethernet link": the cable is out - click the RJ45 jack, or set CABLE to IN.
* DHCP gives no address: use a fixed one in the router's range (192.168.1.x), as the demo does.
* The button seems dead: on this board USER_BTN is HIGH while pressed - test for HIGH, not LOW.
* An integer goes wrong above 32767: int is 16 bits in the simulation - use long.
BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot and the Serial Monitor text:
https://www.theengineeringprojects.com/forum
LICENCES AND THIRD-PARTY NOTES
* The board model (TEPNET.DLL) and the symbols and artwork (TEPH743.LIB) are made by The Engineering Projects. The
source code of the models is not included.
* TEP Boards for Proteus (Arduino Code): its core, the variants and the EEPROM, SPI and Wire libraries are modified
copies of the Arduino AVR core 1.8.6 - GNU Lesser General Public License 2.1 (LGPL 2.1, the text:
LICENSE-LGPL-2.1.txt); its STM32Ethernet (the API of STMicroelectronics' STM32Ethernet) and the others and our core
files are MIT (LICENSE-MIT.txt).
* Proteus is a product of Labcenter Electronics and is not included. STM32, Nucleo and ST are names of
STMicroelectronics, Arduino of Arduino. This library is not made or endorsed by them or by Labcenter.
REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied. Install TEP Boards for Proteus (INSTALLATION step 5), open Arduino Code\H743_Server_Room,
select ST NUCLEO-H743ZI2 (TEP Proteus) and use Sketch > Export Compiled Binary. For a real board use the STM32duino core
with STM32duino LwIP and STM32Ethernet (the same sketch), or STM32CubeIDE with the STM32CubeH7 package. Its pins work
at 3.3 V.
MODEL SCOPE AND LIMITS
Modelled: D0 .. D15 and A0 .. A5; digital I/O, analogRead 0 .. 1023, PWM (analogWrite), tone and attachInterrupt
through the board model; Serial (the board's monitor), Serial1, Wire and SPI; LD1 .. LD3, USER and RESET; Ethernet to
the router's LAN (fixed address or DHCP, TCP servers and clients, UDP), the cable, LINK / ACT.
Not modelled: the STM32H743 itself, its cache, DMA and graphics, the user USB, the other Zio and the morpho headers,
IPv6. The simulation runs below real time.
VERSION
TEP NUCLEO-H743ZI2 library V1.0 (Nov 2026). Device NUCLEO-H743ZI2 (TEPH743.LIB / TEPNET.DLL), TEP Boards for Proteus
1.72.0 (adds this board: STM32Ethernet, D0 .. D15, A0 .. A5, LED_GREEN / LED_YELLOW / LED_RED, USER_BTN).
Demo sketch H743_Server_Room V1.0. Demo parts: BME280 (Advance), MOBILE WIFI MONITOR.Development1 release
-
V1.0NUCLEO-H743ZI2 Library for Proteus V1.0this page
V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.
Installation10 steps
From the download to a working project, in order. The steps follow what the package contains.
You will need
- Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
- Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
- The compiler named in the tutorialto build the source files into firmware
- Any archive toolWindows, macOS and Linux extract ZIP files on their own
Steps
- 1
Extract the archive
Right-click 205129f8594d421483ddf389f5ae8715.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (NUCLEO-H743ZI2-TEP-v1.0) as it is.
- 2
Copy the library files into Proteus
Move TEPBME280.LIB, TEPH743.LIB and TEPLAPTOP.LIB and 1 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.
- 3
Add the simulation model
Copy TEPBME280.DLL and TEPNET.DLL into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.
- 4
Restart Proteus and place the component
Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.
- 5
Install the Arduino library
In the Arduino IDE choose Sketch → Include Library → Add .ZIP Library and pick the library, or copy its folder into Documents\Arduino\libraries. Restart the IDE to see its examples.
- 6
Open the sketch in the Arduino IDE
Open H743_Server_Room.ino, eeprom_clear.ino and eeprom_crc.ino and 17 more, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.
- 7
Build the source code
Open abi.cpp, Arduino.h and binary.h and 52 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.
- 8
Load the HEX file
In Proteus double-click the microcontroller, set Program File to H743_Server_Room.hex and run the simulation. For real hardware, flash the same file with your programmer.
- 9
Open the example simulation
Open H743-Ethernet-Server-Room.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.
- 10
Follow the tutorial
NUCLEO-H743ZI2 Library for Proteus: STM32H7 Ethernet Simulation explains every connection and setting in order; keep it open beside the files while you build.
FAQs9 questionsContact TEP
How do I download NUCLEO-H743ZI2 Library for Proteus V1.0?
Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.
What is inside the archive?
NUCLEO-H743ZI2 Library for Proteus V1.0 comes as a ZIP archive of 302 files (3.6 MB, 8.1 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code. Open the File Structure tab for the full list of 302 files.
What should I do if the download does not start?
Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.
Is this file free?
Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.
How do I check that the file arrived complete?
Compare its SHA-256 with the one on this page, 025030751951ca40ff768266158cd9de4d8ae9fd4777c9bad3ace3d9b30361f3. In PowerShell run Get-FileHash "205129f8594d421483ddf389f5ae8715.zip"; on macOS or Linux run shasum -a 256 "205129f8594d421483ddf389f5ae8715.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.
Do I need WinRAR to open the ZIP file?
No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.
Where do I put the LIB and IDX files?
Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.
Which Proteus version does the library need?
The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.
How do I get the HEX file into the simulation?
Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.
Members skip the wait. Log in or join TEP.
- 0Total downloads
- 4%Popularity
- ProteusCategory
- 0Comments
- ssyedzainnasirUploaded by
- 19 Nov 2026Uploaded at
025030751951ca40ff768266158cd9de4d8ae9fd4777c9bad3ace3d9b30361f3
















Comments
0