Project Files of nRF5340 Audio DK Library for Proteus: LE Audio Kit Simulation
8dd1515409264a9c99dbdd8d667e9cb7.zip

nRF5340 Audio DK Library for Proteus V1.0
nRF5340 Audio DK Library for Proteus V1.0 comes as a ZIP archive of 320 files (3.8 MB, 8.8 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code.
- LIBProteus library
- DLLProteus model
- DSNProteus simulation
- INOArduino sketch
- LIBArduino library
- HEXHEX firmware
- SRCSource code
Description
nRF5340-Audio-DK-Library-for-Proteus-v1.0.zip with Nordic's nRF5340 Audio DK in Proteus (your sketch with D0 .. D13, A0 .. A5, the five buttons and five LEDs, Bluetooth LE to a phone and a serial monitor; TEPAUDIODK.LIB, TEPNET.DLL and the TEP Boards for Proteus add-on 1.84.0), the mini speaker, resistor and phone libraries, the music box demo and a README.
File Structure
6.8 KB1.1 KB7.7 KB11 KB8.5 KB1.5 KB1.7 KB1.9 KB5.7 KB4.9 KB1.1 KB5.8 KB9.6 KB7.2 KB2.5 KB2.1 KB1.9 KB2.1 KB4.4 KB1.1 KB3 KB3 KB1.8 KB2.5 KB3.5 KB149 B2.7 KB2 KB6.4 KB3.2 KB1.3 KB963 B8.6 KB5.9 KB6 KB12 KB1.6 KB1.3 KB14.7 KB4.3 KB6.1 KB20.1 KB8.2 KB2 KB4.5 KB311 B12.8 KB6.7 KB6.1 KB2.2 KB3.4 KB5.9 KB1.5 KB1.6 KB16.6 KB9.7 KB6.9 KB2.1 KB533 B5.7 KB7.4 KB514 B1.7 KB896 B481 B1.4 KB1012 B482 B936 B559 B467 B3.6 KB3.8 KB504 B956 B575 B455 B8.3 KB10.9 KB522 B79 B5.5 KB3.1 KB79 B442 B918 B1.4 KB1.8 KB1 KB1.3 KB1.4 KB1.8 KB1.4 KB5.7 KB502 B463 B5 KB6.5 KB3.4 KB3.4 KB500 B1.6 KB368 B406 B466 B404 B444 B460 B477 B739 B448 B1.3 KB350 B5.7 KB4 KB562 B1.5 KB2 KB550 B7.2 KB4.1 KB371 B4.5 KB3.5 KB492 B390 B478 B6.6 KB2.4 KB479 B5.1 KB1.9 KB1.3 KB1.3 KB750 B1.3 KB490 B2.2 KB1.9 KB498 B1.2 KB1.2 KB487 B5.1 KB4.6 KB371 B3.6 KB2.5 KB534 B1.5 KB1.2 KB478 B6.2 KB3 KB1.5 KB1.7 KB469 B1 KB1.7 KB433 B294 B358 B1.3 KB2.5 KB13.2 KB3.8 KB659 B510 B4.4 KB1.9 KB5.8 KB11 KB835 B518 B308 B1.3 KB3.3 KB568 B6.4 KB2.3 KB29 B436 B9.2 KB4.9 KB439 B4.2 KB1.5 KB9.3 KB7.1 KB4.7 KB2.4 KB388 B5.1 KB893 B667 B1.3 KB5.5 KB2.3 KB1.8 KB468 B882 B530 B791 B487 B894 B2 KB730 B646 B2.6 KB977 B702 B20.6 KB1.8 KB11.8 KB3.2 KB596 B406 B6.3 KB5.7 KB9.3 KB7.7 KB7.7 KB6.1 KB5.8 KB5.9 KB6.4 KB6.4 KB5.3 KB5.6 KB5.7 KB7.9 KB7.7 KB6.5 KB6.3 KB6.2 KB6.4 KB5.9 KB10.3 KB8.5 KB6.6 KB7.6 KB6.7 KB6.1 KB6.7 KB8.3 KB6.2 KB7.2 KB6.2 KB5.9 KB5.6 KB5.7 KB6.7 KB5.9 KB6.2 KB6 KB6 KB6.1 KB6.3 KB6 KB6.1 KB6.2 KB6 KB5.8 KB6.4 KB6.4 KB3.8 KB6.4 KB7.3 KB6.4 KB6.9 KB6 KB6.8 KB7 KB6.3 KB6.4 KB6.5 KB6.5 KB6.6 KB6.5 KB5.9 KB6.1 KB5.6 KB6.6 KB5.9 KB7.5 KB3.8 KB4.4 KB5.4 KB7.7 KB7.1 KB5.8 KB5.9 KB5.9 KB6.9 KB5.7 KB5.9 KB5.8 KB5.5 KB5.5 KB7.1 KB5.2 KB41.3 KB25.9 KB1.3 KB8.5 KB37.3 KB42.9 KB39.5 KB13.1 KB306.9 KB11 KB3.0 MB311 KB286 KB33 KB23.7 KB3.0 MB311 KB286 KB14.4 KBGallery12 images from the tutorialOpen the tutorial
The circuit, the board and the results as they appear in nRF5340 Audio DK Library for Proteus: LE Audio Kit Simulation. Open an image for its full size.












README
NRF5340 AUDIO DK LIBRARY FOR PROTEUS - V1.0 (YOUR ARDUINO SKETCH, BLUETOOTH LE TO A PHONE, FIVE BUTTONS AND FIVE LEDS)
Designed by The Engineering Projects
www.TheEngineeringProjects.com
IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
https://www.theengineeringprojects.com/2026/11/nrf5340-audio-dk-library-for-proteus.html
Report a bug or suggest a feature (our forum):
https://www.theengineeringprojects.com/forum
The demo's other parts are our libraries (included) - their articles:
https://www.theengineeringprojects.com/2026/11/mini-speaker-library-for-proteus.html
https://www.theengineeringprojects.com/2026/11/resistor-library-for-proteus.html
https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
Support us (the libraries are free):
https://www.theengineeringprojects.com/donate
FILE STRUCTURE
nRF5340-Audio-DK-TEP-v1.0/
|-- Proteus Library Files/
| |-- TEPAUDIODK.LIB 42.9 KB the nRF5340 Audio DK, to LIBRARY
| |-- TEPLAPTOP.LIB 39.5 KB the laptop (demo), to LIBRARY
| |-- TEPMOBILE.LIB 13.1 KB the phone (demo), to LIBRARY
| |-- TEPRESISTOR.LIB 306.9 KB the resistor (demo), to LIBRARY
| |-- TEPSPEAKER.LIB 11.0 KB the mini speaker (demo), to LIBRARY
|-- Proteus Model Files/
| |-- TEPNET.DLL 2.96 MB the board + monitors + network, to MODELS
| |-- TEPRESISTOR.DLL 311.0 KB the resistor, to MODELS
| |-- TEPSPEAKER.DLL 286.0 KB the mini speaker, to MODELS
|-- Arduino Code/
| |-- AudioDK_BLE_Player/AudioDK_BLE_Player.ino 6.8 KB the demo sketch
| |-- TEP Boards for Proteus/hardware/ 1.28 MB the Arduino IDE add-on 1.84.0 (305 files)
|-- Proteus Simulation/
| |-- AudioDK_BLE_Player.hex 33.0 KB the demo sketch (U1)
| |-- nRF5340-Audio-DK-BLE-Music-Box.pdsprj 23.7 KB the demo: a Bluetooth LE music box
| |-- TEPNET.DLL 2.96 MB copy of the model
| |-- TEPRESISTOR.DLL 311.0 KB copy of the model
| |-- TEPSPEAKER.DLL 286.0 KB copy of the model
|-- README.txt ~13.9 KB this file
Total: 8.84 MB (unzipped). The source code of the models is not included.
WHAT IS IT?
Proteus 8 has no nRF5340 processor model, so this is NOT a real nRF5340 chip. Our team has put a lot of effort into
building this board ourselves: it is Nordic Semiconductor's nRF5340 Audio DK (PCA10121) - the blue LE Audio
development kit with the nRF5340 SoC (two Arm Cortex-M33 cores: the application core up to 128 MHz and the network
core at 64 MHz; 1 MB of flash, 512 KB of RAM; Bluetooth LE with LE Audio), its PCB antenna, the CS47L63 audio DSP, the
digital microphone, the LINE IN and HEADPHONE jacks, the SD card slot, the nPM1100 PMIC with the battery connector,
the built-in debugger with its USB port, the five buttons and the five LEDs - drawn compact, and it runs YOUR Arduino
sketch in Proteus:
* You write a normal sketch for the DK's Arduino-mapped header (D0 .. D13, A0 .. A5, SDA, SCL; analogRead 0-1023,
analogWrite, attachInterrupt, pulseInLong, tone, Wire, SPI, Serial, Serial1) and compile it in the Arduino IDE
with our board package "TEP Boards for Proteus" 1.84.0 (in Arduino Code - see INSTALLATION).
* As on the real kit, the buttons and LEDs SHARE header pins: PLAY/PAUSE, BTN 5 and BTN 4 are A0, A1 and A2, RGB1
is A3, A4 and A5, LED1 (blue), LED2 and LED3 (green) are D2, D3 and D4. VOL-, VOL+ and RGB2 are not on the header.
* ALL the LEDs light when HIGH (the real kit's). The buttons read LOW while you hold them: click a button on the
board in the running simulation.
* D0 is Serial1's TX and D1 its RX - the real kit's UART1 (TX P1.09, RX P1.08), the other way round from most
Arduino boards.
* PWM with your own frequency and duty: ledcAttach(pin, frequency, bits), ledcChangeFrequency and ledcWrite(pin,
duty) of the board package - the demo plays its notes with them (on the real nRF5340: its PWM peripheral).
* Bluetooth LE works through ArduinoBLE: the board advertises as a peripheral with your services and
characteristics, and our Mobile WiFi Monitor's Bluetooth app is the central (it lists the board, connects, reads,
writes and gets the notifications).
TEP additions: the USB port opens the serial monitor (the same window as our TEP Serial Monitor Advance).
Limits (say them before you start): one phone is the central; the board cannot be a central itself, and LE Audio
streams (Auracast, CIS, BIS) are not modelled. The CS47L63, the microphone, the jacks, the SD card slot, the PMIC,
the power monitors and USB audio are drawn, not modelled - the demo's sound comes from our mini speaker on D5. Your
sketch gets 8 KB of RAM in the simulation (the real one: 512 KB), about 256 KB of flash, and int is 16 bits in the
simulation (use long for big numbers). See MODEL SCOPE AND LIMITS
Modelled: the DK's Arduino-mapped header; digital I/O, analogRead 0 .. 1023, PWM (analogWrite, ledcWrite), pulse
timing, tone and attachInterrupt through the board model; Serial (the board's monitor), Serial1, Wire and SPI; the
five buttons, RGB1, RGB2, LED1 .. LED3 and RESET; Bluetooth LE as a peripheral (ArduinoBLE) with the phone as the
central.
Not modelled: the nRF5340 itself, its network core, LE Audio, the CS47L63 audio DSP, the microphone, the jacks, the SD
card, the PMIC and battery, the power monitors, USB audio, the radio's range, the board as a central. The simulation
runs below real time.
ONE DEVICE (search "NRF5340" in Pick Devices):
NRF5340 AUDIO DK "nRF5340 Audio DK" V1.0 (Microprocessor ICs > Bluetooth Boards), prefix U, model TEPNET.DLL.
Its TEP window has no Windows title bar: the serial monitor (the USB port, 115200 baud: Monitor, Plotter and Board
tabs).
The same TEPNET.DLL also runs our other sketch boards and the phone; it replaces any older TEPNET.DLL (keep only this
newest one in MODELS).
TEST STATUS
V1.0: verified in Proteus 8.5 on 18 Nov 2026 with the demo project as shipped. What the Proteus run showed:
* nRF5340-Audio-DK-BLE-Music-Box: "Advertising as "Audio DK Music"", RGB1 yellow, LED1 + LED2 (volume 6); the phone's
Bluetooth app, SCAN, connect: "Phone connected", RGB2 blue, the melody, the state and the volume on the phone.
* PLAY/PAUSE ">> PLAY": ODE TO JOY on the mini speaker (RGB1 green, the cone moving); VOL+ three times ">> VOLUME 7",
"8" (LED3 on), "9"; BTN 5 ">> NEXT 3/3: JINGLE BELLS"; the melodies went on by themselves ("the melody ended").
* PLAY/PAUSE ">> PAUSE" (RGB1 yellow), VOL- ">> VOLUME 8", PLAY/PAUSE ">> PLAY"; the phone followed every change.
* about 90 s of simulation, no errors, with the phone and the monitor open.
INSTALLATION (about 3 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" to the LIBRARY folder of Proteus, for example:
C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
(on some PCs: C:\ProgramData\Labcenter Electronics\Proteus 8 Professional\LIBRARY). TEPAUDIODK.LIB is the board;
TEPSPEAKER.LIB and TEPRESISTOR.LIB are the demo's mini speaker and resistor, TEPMOBILE.LIB and TEPLAPTOP.LIB the
phone and the laptop.
3. Copy the DLLs from "Proteus Model Files" (TEPNET.DLL, TEPSPEAKER.DLL, TEPRESISTOR.DLL) to the MODELS folder
(...\Proteus 8 Professional\MODELS) - replace an older TEPNET.DLL (this one is the first that knows this board).
4. Delete TEPAUDIODK.IDX from the LIBRARY folder if it is there.
5. The Arduino IDE (only to compile your own sketches - the demo has its HEX file): copy the folder
"Arduino Code\TEP Boards for Proteus\hardware" into your sketchbook folder (normally Documents\Arduino), so that
Documents\Arduino\hardware\tep\avr\boards.txt exists (replace an older copy); restart the IDE. The Arduino AVR Boards
platform must be installed (it comes with IDE 1.8.x; in IDE 2.x install "Arduino AVR Boards" from the Boards
Manager once).
Tools > Board > TEP Boards for Proteus > Nordic nRF5340 Audio DK (TEP Proteus). ArduinoBLE is in the board package.
6. Start Proteus. In Pick Devices (P) search "NRF5340".
RUN THE DEMO
Keep the .hex file and the DLLs beside the project in "Proteus Simulation".
nRF5340-Audio-DK-BLE-Music-Box.pdsprj - U1 the nRF5340 Audio DK (AudioDK_BLE_Player.hex) is a music box: D5 drives
LS1, our 28 mm 8 ohm mini speaker (true scale), through R1 (100 ohm); MOB1 = the phone (Mobile WiFi Monitor), whose
Bluetooth app connects to it.
Press Run. The monitor prints "Advertising as "Audio DK Music""; RGB1 is yellow (paused). On the phone open the
Bluetooth app, press SCAN and connect: RGB2 lights blue, and the phone shows the melody, the state and the volume.
Click PLAY/PAUSE: ODE TO JOY plays on the speaker (RGB1 green; your PC's speaker plays it too). VOL- and VOL+ change
the volume from 0 to 10 (LED1 from 1, LED2 from 4, LED3 from 8); BTN 5 is the next melody, BTN 4 the previous one;
PLAY/PAUSE again pauses (yellow). A melody that ends starts the next one. The melodies: ODE TO JOY, TWINKLE TWINKLE,
JINGLE BELLS.
Closed a window? The USB port opens the monitor, a click on the speaker its window, a click on the phone's screen the
phone.
THE PINS (the label on the part, what it can do in the simulation; the real kit's GPIO from Zephyr's nrf5340_audio_dk)
D0, D1 Serial1 TX and RX (!), or GPIO (P1.09, P1.08)
D2, D3, D4 GPIO, PWM, interrupt - and LED1 (blue), LED2, LED3 (green) (P0.31, P1.00, P1.01)
D5 .. D9 GPIO, PWM, interrupt, pulse timing (P1.14, P1.07, P1.11, P1.10, P1.13)
D10 .. D13 GPIO, PWM; SPI SS, MOSI, MISO, SCK (P1.12, P0.09, P0.10, P0.08)
A0, A1, A2 analogRead or GPIO - and the buttons PLAY/PAUSE, BTN 5, BTN 4 (P0.04, P0.05, P0.06)
A3, A4, A5 analogRead or GPIO - and RGB1 red, green, blue (P0.07, P0.25, P0.26)
SDA, SCL Wire (P1.02, P1.03)
VDD, 5V, GND 3.3 V (the logic), 5 V, ground; RESET the board's reset (the RESET button too)
AREF, VIN drawn, not modelled
Off the header: VOL- (22, the real P0.02) and VOL+ (23, P0.03), LOW when pressed; RGB2 red, green, blue (24, 25, 26;
P0.28, P0.29, P0.30). Names in the board package: LED1 .. LED3, LED_RGB1_RED / _GREEN / _BLUE, LED_RGB2_RED / _GREEN /
_BLUE (LED_BUILTIN is LED1, lit when HIGH); BUTTON_VOL_DOWN, BUTTON_VOL_UP, BUTTON_PLAY_PAUSE, BUTTON4, BUTTON5
(BUTTON1 .. BUTTON3 are VOL-, VOL+ and PLAY/PAUSE; BTN_BUILTIN is BUTTON1); pinMode INPUT_PULLUP for the buttons.
Serial is the USB: the board's built-in monitor.
PROPERTIES (double-click the part > Edit Properties)
PROGRAM the sketch's HEX (Arduino IDE: Sketch > Export Compiled Binary, board Nordic nRF5340 Audio DK)
MONITOR YES = the built-in serial monitor on Serial; BAUD its speed (115200, or AUTO)
AUTOOPEN YES = the monitor window opens at Run (the demo: YES)
TROUBLESHOOTING
* The phone's list is empty: call BLE.begin(), set a local name and BLE.advertise(); call BLE.poll() in loop().
* The speaker stays silent: ledcAttach(5, 1000, 8) once, then ledcChangeFrequency and ledcWrite with a duty above 0;
the speaker needs its 100 ohm resistor (8 ohm straight on a pin asks for far too much current).
* A button does nothing: use pinMode(BUTTON_..., INPUT_PULLUP) and act when digitalRead() is LOW.
* An LED stays dark: the Audio DK's LEDs light when the pin is HIGH (not LOW as on other Nordic kits).
* analogRead(A0) reads 1023: A0 .. A2 carry the buttons' pull-ups - use A3 .. A5 only if you do not need RGB1.
* An integer goes wrong above 32767: int is 16 bits in the simulation - use long.
BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot and the Serial Monitor text:
https://www.theengineeringprojects.com/forum
LICENCES AND THIRD-PARTY NOTES
* The board model (TEPNET.DLL), the symbols and artwork (TEPAUDIODK.LIB) and the mini speaker and resistor models are
made by The Engineering Projects. The source code of the models is not included.
* TEP Boards for Proteus (Arduino Code): its core, the variants and the EEPROM, SPI and Wire libraries are modified
copies of the Arduino AVR core 1.8.6 - GNU Lesser General Public License 2.1 (LGPL 2.1, the text:
LICENSE-LGPL-2.1.txt); its ArduinoBLE and the others and our core files are MIT (LICENSE-MIT.txt).
* Our ArduinoBLE has the calls of the library of that name; its code is ours. The melodies are traditional tunes in the
public domain.
* Proteus is a product of Labcenter Electronics and is not included. nRF5340 and Nordic Semiconductor are names of
Nordic Semiconductor ASA, CS47L63 of Cirrus Logic, Arduino of Arduino. The Bluetooth word mark belongs to Bluetooth
SIG. This library is not made or endorsed by them or by Labcenter.
REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied. Install TEP Boards for Proteus (INSTALLATION step 5), open Arduino Code\AudioDK_BLE_Player,
select Nordic nRF5340 Audio DK (TEP Proteus) and use Sketch > Export Compiled Binary. For a real board use Nordic's nRF
Connect SDK (its nRF5340 Audio application, or Zephyr with the board nrf5340_audio_dk/nrf5340/cpuapp). Its pins work
at 3.3 V.
MODEL SCOPE AND LIMITS
Modelled: the DK's Arduino-mapped header; digital I/O, analogRead 0 .. 1023, PWM (analogWrite, ledcWrite), pulse
timing, tone and attachInterrupt through the board model; Serial (the board's monitor), Serial1, Wire and SPI; the
five buttons, RGB1, RGB2, LED1 .. LED3 and RESET; Bluetooth LE as a peripheral (ArduinoBLE) with the phone as the
central.
Not modelled: the nRF5340 itself, its network core, LE Audio, the CS47L63 audio DSP, the microphone, the jacks, the SD
card, the PMIC and battery, the power monitors, USB audio, the radio's range, the board as a central. The simulation
runs below real time.
VERSION
TEP nRF5340 Audio DK library V1.0 (Nov 2026). Device NRF5340 AUDIO DK (TEPAUDIODK.LIB / TEPNET.DLL), TEP Boards for
Proteus 1.84.0 (adds this board: the five buttons, RGB1, RGB2, LED1 .. LED3, Serial1 TX on D0).
Demo sketch AudioDK_BLE_Player V1.0. Demo parts: MINISPEAKER28TEP, RESISTOR4BANDTEP and MOBILE WIFI MONITOR.Development1 release
-
V1.0nRF5340 Audio DK Library for Proteus V1.0this page
V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.
Installation10 steps
From the download to a working project, in order. The steps follow what the package contains.
You will need
- Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
- Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
- The compiler named in the tutorialto build the source files into firmware
- Any archive toolWindows, macOS and Linux extract ZIP files on their own
Steps
- 1
Extract the archive
Right-click 8dd1515409264a9c99dbdd8d667e9cb7.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (nRF5340-Audio-DK-TEP-v1.0) as it is.
- 2
Copy the library files into Proteus
Move TEPAUDIODK.LIB, TEPLAPTOP.LIB and TEPMOBILE.LIB and 2 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.
- 3
Add the simulation model
Copy TEPNET.DLL, TEPRESISTOR.DLL and TEPSPEAKER.DLL into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.
- 4
Restart Proteus and place the component
Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.
- 5
Install the Arduino library
In the Arduino IDE choose Sketch → Include Library → Add .ZIP Library and pick the library, or copy its folder into Documents\Arduino\libraries. Restart the IDE to see its examples.
- 6
Open the sketch in the Arduino IDE
Open AudioDK_BLE_Player.ino, eeprom_clear.ino and eeprom_crc.ino and 17 more, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.
- 7
Build the source code
Open abi.cpp, Arduino.h and binary.h and 52 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.
- 8
Load the HEX file
In Proteus double-click the microcontroller, set Program File to AudioDK_BLE_Player.hex and run the simulation. For real hardware, flash the same file with your programmer.
- 9
Open the example simulation
Open nRF5340-Audio-DK-BLE-Music-Box.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.
- 10
Follow the tutorial
nRF5340 Audio DK Library for Proteus: LE Audio Kit Simulation explains every connection and setting in order; keep it open beside the files while you build.
FAQs9 questionsContact TEP
How do I download nRF5340 Audio DK Library for Proteus V1.0?
Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.
What is inside the archive?
nRF5340 Audio DK Library for Proteus V1.0 comes as a ZIP archive of 320 files (3.8 MB, 8.8 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code. Open the File Structure tab for the full list of 320 files.
What should I do if the download does not start?
Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.
Is this file free?
Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.
How do I check that the file arrived complete?
Compare its SHA-256 with the one on this page, 3b50baf26a098d3094f88ca98c4bdb846b8501e16dcee46838e9bfa323dc1829. In PowerShell run Get-FileHash "8dd1515409264a9c99dbdd8d667e9cb7.zip"; on macOS or Linux run shasum -a 256 "8dd1515409264a9c99dbdd8d667e9cb7.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.
Do I need WinRAR to open the ZIP file?
No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.
Where do I put the LIB and IDX files?
Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.
Which Proteus version does the library need?
The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.
How do I get the HEX file into the simulation?
Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.
Members skip the wait. Log in or join TEP.
- 0Total downloads
- 4%Popularity
- ProteusCategory
- 0Comments
- ssyedzainnasirUploaded by
- 21 Nov 2026Uploaded at
3b50baf26a098d3094f88ca98c4bdb846b8501e16dcee46838e9bfa323dc1829
















Comments
0