Project Files of nRF52 DK Library for Proteus: nRF52832 Bluetooth LE Simulation
d5bafb599d5844309b76d6b1a98f0fce.zip

nRF52 DK Library for Proteus V1.0
nRF52 DK Library for Proteus V1.0 comes as a ZIP archive of 311 files (3.2 MB, 7.3 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code.
- LIBProteus library
- DLLProteus model
- DSNProteus simulation
- INOArduino sketch
- LIBArduino library
- HEXHEX firmware
- SRCSource code
Description
nRF52-DK-Library-for-Proteus-v1.0.zip with Nordic's nRF52 DK in Proteus (your sketch with D0 .. D13, A0 .. A5, LED1 .. LED4 on D6 .. D9, BUTTON1 .. BUTTON4 on D2 .. D5, Bluetooth LE to a phone and a serial monitor; TEPNRF52DK.LIB, TEPNET.DLL and the TEP Boards for Proteus add-on 1.81.0), the phone library, the classroom poll demo with its sketch and a README.
File Structure
4.2 KB1.1 KB7.7 KB11 KB8.5 KB1.5 KB1.7 KB1.9 KB5.7 KB4.9 KB1.1 KB5.8 KB9.6 KB7.2 KB2.5 KB2.1 KB1.9 KB2.1 KB4.4 KB1.1 KB3 KB3 KB1.8 KB2.5 KB3.5 KB149 B2.7 KB2 KB6.4 KB3.2 KB1.3 KB963 B8.6 KB5.9 KB6 KB12 KB1.6 KB1.3 KB14.7 KB4.3 KB6.1 KB20.1 KB8.2 KB2 KB4.5 KB311 B12.8 KB6.7 KB6.1 KB2.2 KB3.4 KB5.9 KB1.5 KB1.6 KB16.6 KB9.7 KB6.9 KB2.1 KB533 B5.7 KB7.4 KB514 B1.7 KB896 B481 B1.4 KB1012 B482 B936 B559 B467 B3.6 KB3.8 KB504 B956 B575 B455 B8.3 KB10.9 KB522 B79 B5.5 KB3.1 KB79 B442 B918 B1.4 KB1.8 KB1 KB1.3 KB1.4 KB1.8 KB1.4 KB5.7 KB502 B463 B5 KB6.5 KB3.4 KB3.4 KB500 B1.6 KB368 B406 B466 B404 B444 B460 B477 B739 B448 B1.3 KB350 B5.7 KB4 KB562 B1.5 KB2 KB550 B7.2 KB4.1 KB371 B4.5 KB3.5 KB492 B390 B478 B6.6 KB2.4 KB479 B5.1 KB1.9 KB1.3 KB1.3 KB750 B1.3 KB490 B2.2 KB1.9 KB498 B1.2 KB1.2 KB487 B5.1 KB4.6 KB371 B3.6 KB2.5 KB534 B1.5 KB1.2 KB478 B6.2 KB3 KB1.5 KB1.7 KB469 B1 KB1.7 KB433 B294 B358 B1.3 KB2.5 KB13.2 KB3.8 KB659 B510 B4.4 KB1.9 KB5.8 KB11 KB835 B518 B308 B1.3 KB3.3 KB568 B6.4 KB2.3 KB29 B436 B9.2 KB4.9 KB439 B4.2 KB1.5 KB9.3 KB7.1 KB4.7 KB2.4 KB388 B5.1 KB893 B667 B1.3 KB5.5 KB2.3 KB1.8 KB468 B882 B530 B791 B487 B894 B2 KB730 B646 B2.6 KB977 B702 B20.6 KB1.8 KB11.8 KB3.2 KB596 B406 B6.3 KB5.7 KB9.3 KB7.7 KB7.7 KB6.1 KB5.8 KB5.9 KB6.4 KB6.4 KB5.3 KB5.6 KB5.7 KB7.9 KB7.7 KB6.5 KB6.3 KB6.2 KB6.4 KB5.9 KB10.3 KB8.5 KB6.6 KB7.6 KB6.7 KB6.1 KB6.7 KB8.3 KB6.2 KB7.2 KB6.2 KB5.9 KB5.6 KB5.7 KB6.7 KB5.9 KB6.2 KB6 KB6 KB6.1 KB6.3 KB6 KB6.1 KB6.2 KB6 KB5.8 KB6.4 KB6.4 KB6.4 KB6.9 KB6 KB6.8 KB7 KB6.3 KB6.4 KB6.5 KB6.5 KB6.6 KB6.5 KB5.9 KB6.1 KB5.6 KB6.6 KB5.9 KB7.5 KB3.8 KB4.4 KB5.4 KB7.7 KB7.1 KB5.8 KB5.9 KB5.9 KB6.9 KB5.7 KB5.9 KB5.8 KB5.5 KB5.5 KB7.1 KB5.2 KB39.7 KB25.9 KB1.3 KB8.5 KB37 KB39.5 KB13.1 KB39 KB3.0 MB31.1 KB18 KB3.0 MB10.7 KBGallery12 images from the tutorialOpen the tutorial
The circuit, the board and the results as they appear in nRF52 DK Library for Proteus: nRF52832 Bluetooth LE Simulation. Open an image for its full size.












README
NRF52 DK LIBRARY FOR PROTEUS - V1.0 (YOUR ARDUINO SKETCH, BLUETOOTH LE TO A PHONE, FOUR LEDS AND FOUR BUTTONS)
Designed by The Engineering Projects
www.TheEngineeringProjects.com
IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
https://www.theengineeringprojects.com/2026/11/nrf52-dk-library-for-proteus.html
Report a bug or suggest a feature (our forum):
https://www.theengineeringprojects.com/forum
The demo's phone is our Mobile WiFi Monitor (included) - its article:
https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
Support us (the libraries are free):
https://www.theengineeringprojects.com/donate
FILE STRUCTURE
nRF52-DK-TEP-v1.0/
|-- Proteus Library Files/
| |-- TEPLAPTOP.LIB 39.5 KB the laptop (demo), to LIBRARY
| |-- TEPMOBILE.LIB 13.1 KB the phone (demo), to LIBRARY
| |-- TEPNRF52DK.LIB 39.0 KB the nRF52 DK, to LIBRARY
|-- Proteus Model Files/
| |-- TEPNET.DLL 2.95 MB the board + monitors + network, to MODELS
|-- Arduino Code/
| |-- DK52_Class_Poll/DK52_Class_Poll.ino 4.2 KB the demo sketch
| |-- TEP Boards for Proteus/hardware/ 1.26 MB the Arduino IDE add-on 1.81.0 (302 files)
|-- Proteus Simulation/
| |-- DK52_Class_Poll.hex 31.1 KB the demo sketch (U1)
| |-- nRF52-DK-BLE-Class-Poll.pdsprj 18.0 KB the demo: a Bluetooth LE classroom poll
| |-- TEPNET.DLL 2.95 MB copy of the model
|-- README.txt ~10.9 KB this file
Total: 7.31 MB (unzipped). The source code of the models is not included.
WHAT IS IT?
Proteus 8 has no nRF52832 processor model, so this is NOT a real nRF52832 chip. Our team has put a lot of effort into
building this board ourselves: it is Nordic Semiconductor's nRF52 DK (PCA10040) - the blue development kit with the
nRF52832 SoC (an Arm Cortex-M4F at 64 MHz with 512 KB of flash and 64 KB of RAM, Bluetooth LE and NFC), its PCB
antenna, the interface MCU (the J-Link) with its USB port, the power switch, four green LEDs and four buttons - drawn
compact, and it runs YOUR Arduino sketch in Proteus:
* You write a normal sketch for the DK's Arduino header (D0 .. D13, A0 .. A5, SDA, SCL; analogRead 0-1023,
analogWrite, attachInterrupt, tone, Wire, SPI, Serial, Serial1) and compile it in the Arduino IDE with our board
package "TEP Boards for Proteus" 1.81.0 (in Arduino Code - see INSTALLATION).
* As on the real nRF52 DK, the buttons and the LEDs share header pins: BUTTON1 .. BUTTON4 are D2 .. D5 (P0.13 ..
P0.16) and LED1 .. LED4 are D6 .. D9 (P0.17 .. P0.20). The LEDs light when LOW (LED_BUILTIN is LED1); the buttons
read LOW while you hold them: click a button on the board in the running simulation. Use D2 .. D9 for other parts
only when you do not need the buttons and LEDs.
* Bluetooth LE works through ArduinoBLE: the board advertises as a peripheral with your services and
characteristics, and our Mobile WiFi Monitor's Bluetooth app is the central (it lists the board, connects, reads,
writes and gets the notifications).
TEP additions: the USB port opens the serial monitor (the same window as our TEP Serial Monitor Advance).
Limits (say them before you start): one phone is the central; the board cannot be a central itself. NFC and the
current measurement header are drawn, not modelled. Your sketch gets 8 KB of RAM in the simulation (the real one: 64
KB), about 256 KB of flash, and int is 16 bits in the simulation (use long for big numbers). See MODEL SCOPE AND LIMITS.
ONE DEVICE (search "NRF52" in Pick Devices):
NRF52 DK "nRF52 DK" V1.0 (Microprocessor ICs > Bluetooth Boards), prefix U, model TEPNET.DLL.
Its TEP window has no Windows title bar: the serial monitor (the USB port, 115200 baud: Monitor, Plotter and Board
tabs).
The same TEPNET.DLL also runs our other sketch boards and the phone; it replaces any older TEPNET.DLL (keep only this
newest one in MODELS).
TEST STATUS
V1.0: verified in Proteus 8.5 on 17 Nov 2026 with the demo project as shipped. What the Proteus run showed:
* nRF52-DK-BLE-Class-Poll: "Advertising as "nRF52 Class Poll""; the phone's Bluetooth app, SCAN, connect: "Phone
connected", Answer A .. D at 0.
* BUTTON3: ">> Vote for C (1)", LED3 on (D8); BUTTON1: "Vote for A (1)", a tie - LED1 and LED3 on, the phone's leader
"A+C (2)"; BUTTON1 again: A leads, LED1 only.
* BUTTON4 three times: A+D tie, then "A 2 B 0 C 1 D 3 leader D", LED4 only; the phone followed every vote.
* about 18 s of simulation, no errors, with the phone and the monitor open.
INSTALLATION (about 3 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" to the LIBRARY folder of Proteus, for example:
C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
(on some PCs: C:\ProgramData\Labcenter Electronics\Proteus 8 Professional\LIBRARY). TEPNRF52DK.LIB is the board;
TEPMOBILE.LIB and TEPLAPTOP.LIB are the phone and the laptop.
3. Copy TEPNET.DLL from "Proteus Model Files" to the MODELS folder (...\Proteus 8 Professional\MODELS) - replace an
older TEPNET.DLL (this one is the first that knows this board).
4. Delete TEPNRF52DK.IDX from the LIBRARY folder if it is there.
5. The Arduino IDE (only to compile your own sketches - the demo has its HEX file): copy the folder
"Arduino Code\TEP Boards for Proteus\hardware" into your sketchbook folder (normally Documents\Arduino), so that
Documents\Arduino\hardware\tep\avr\boards.txt exists (replace an older copy); restart the IDE. The Arduino AVR Boards
platform must be installed (it comes with IDE 1.8.x; in IDE 2.x install "Arduino AVR Boards" from the Boards
Manager once).
Tools > Board > TEP Boards for Proteus > Nordic nRF52 DK (TEP Proteus). ArduinoBLE is in the board package.
6. Start Proteus. In Pick Devices (P) search "NRF52".
RUN THE DEMO
Keep the .hex file and TEPNET.DLL beside the project in "Proteus Simulation".
nRF52-DK-BLE-Class-Poll.pdsprj - U1 the nRF52 DK (DK52_Class_Poll.hex) is a four-answer classroom poll; MOB1 = the
teacher's phone (Mobile WiFi Monitor), whose Bluetooth app connects to it. No wires: the buttons and LEDs are on the DK.
Press Run. The monitor prints "Advertising as "nRF52 Class Poll"". On the phone open the Bluetooth app, press SCAN and
connect: the phone lists Answer A .. D and the Leader. Click BUTTON1 .. BUTTON4 (the answers A .. D): every click is a
vote, the monitor prints the standings, and the LED of the leading answer lights (LED1 = A .. LED4 = D); in a tie all
the leaders' LEDs light.
Closed a window? The USB port opens the monitor, a click on the phone's screen the phone.
THE PINS (the label on the part, what it can do in the simulation; the real DK's GPIO from Zephyr's nrf52dk_nrf52832)
D0, D1 Serial1 RX and TX, or GPIO (P0.11, P0.12)
D2 .. D5 GPIO, PWM, interrupt - and BUTTON1 .. BUTTON4 (P0.13 .. P0.16)
D6 .. D9 GPIO, PWM, interrupt - and LED1 .. LED4 (P0.17 .. P0.20)
D10 .. D13 GPIO, PWM, interrupt; SPI SS, MOSI, MISO, SCK (P0.22 .. P0.25)
A0 .. A5 analogRead 0 .. 1023 for 0 .. 3.3 V, or GPIO (P0.03 P0.04 P0.28 .. P0.31; core numbers 14 .. 19)
SDA, SCL Wire (P0.26, P0.27)
VDD, 5V, GND 3.3 V (the logic), 5 V, ground; RESET the board's reset (the RESET button too)
AREF, VIN drawn, not modelled
LED_BUILTIN is LED1, with LED_BUILTIN_ACTIVE (LOW) and LED_BUILTIN_INACTIVE; BTN_BUILTIN is BUTTON1. Serial is the USB:
the board's built-in monitor.
PROPERTIES (double-click the part > Edit Properties)
PROGRAM the sketch's HEX (Arduino IDE: Sketch > Export Compiled Binary with Nordic nRF52 DK (TEP Proteus))
MONITOR YES = the built-in serial monitor on Serial; BAUD its speed (115200, or AUTO)
AUTOOPEN YES = the monitor window opens at Run (the demo: YES)
TROUBLESHOOTING
* The phone's list is empty: call BLE.begin(), set a local name and BLE.advertise(); call BLE.poll() in loop().
* A button does nothing: use pinMode(BUTTONx, INPUT_PULLUP) and act when digitalRead() is LOW; do not drive D2 .. D5.
* An LED lights by itself: something else drives D6 .. D9 - they are the LEDs on this DK.
* The LEDs look inverted: they light when the pin is LOW, as on the real DK.
* An integer goes wrong above 32767: int is 16 bits in the simulation - use long.
BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot and the Serial Monitor text:
https://www.theengineeringprojects.com/forum
LICENCES AND THIRD-PARTY NOTES
* The board model (TEPNET.DLL) and the symbols and artwork (TEPNRF52DK.LIB) are made by The Engineering Projects. The
source code of the models is not included.
* TEP Boards for Proteus (Arduino Code): its core, the variants and the EEPROM, SPI and Wire libraries are modified
copies of the Arduino AVR core 1.8.6 - GNU Lesser General Public License 2.1 (LGPL 2.1, the text:
LICENSE-LGPL-2.1.txt); its ArduinoBLE and the others and our core files are MIT (LICENSE-MIT.txt).
* Our ArduinoBLE has the calls of the library of that name; its code is ours.
* Proteus is a product of Labcenter Electronics and is not included. nRF52832 and Nordic Semiconductor are names of
Nordic Semiconductor ASA, Arduino of Arduino. The Bluetooth word mark belongs to Bluetooth SIG. This library is not
made or endorsed by them or by Labcenter.
REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied. Install TEP Boards for Proteus (INSTALLATION step 5), open Arduino Code\DK52_Class_Poll,
select Nordic nRF52 DK (TEP Proteus) and use Sketch > Export Compiled Binary. For a real board use Nordic's nRF Connect
SDK (or Zephyr with the board nrf52dk/nrf52832). Its pins work at 3.3 V.
MODEL SCOPE AND LIMITS
Modelled: the DK's Arduino header; digital I/O, analogRead 0 .. 1023, PWM (analogWrite), tone and attachInterrupt
through the board model; Serial (the board's monitor), Serial1, Wire and SPI; the four LEDs on D6 .. D9, the four
buttons on D2 .. D5 and RESET; Bluetooth LE as a peripheral (ArduinoBLE) with the phone as the central.
Not modelled: the nRF52832 itself, the radio's range, NFC, the current measurement header, the board as a central.
The simulation runs below real time.
VERSION
TEP nRF52 DK library V1.0 (Nov 2026). Device NRF52 DK (TEPNRF52DK.LIB / TEPNET.DLL), TEP Boards for Proteus 1.81.0
(adds this board: LED1 .. LED4 on D6 .. D9, BUTTON1 .. BUTTON4 on D2 .. D5).
Demo sketch DK52_Class_Poll V1.0. Demo part: MOBILE WIFI MONITOR.Development1 release
-
V1.0nRF52 DK Library for Proteus V1.0this page
V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.
Installation10 steps
From the download to a working project, in order. The steps follow what the package contains.
You will need
- Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
- Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
- The compiler named in the tutorialto build the source files into firmware
- Any archive toolWindows, macOS and Linux extract ZIP files on their own
Steps
- 1
Extract the archive
Right-click d5bafb599d5844309b76d6b1a98f0fce.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (nRF52-DK-TEP-v1.0) as it is.
- 2
Copy the library files into Proteus
Move TEPLAPTOP.LIB, TEPMOBILE.LIB and TEPNRF52DK.LIB and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.
- 3
Add the simulation model
Copy TEPNET.DLL into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.
- 4
Restart Proteus and place the component
Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.
- 5
Install the Arduino library
In the Arduino IDE choose Sketch → Include Library → Add .ZIP Library and pick the library, or copy its folder into Documents\Arduino\libraries. Restart the IDE to see its examples.
- 6
Open the sketch in the Arduino IDE
Open DK52_Class_Poll.ino, eeprom_clear.ino and eeprom_crc.ino and 17 more, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.
- 7
Build the source code
Open abi.cpp, Arduino.h and binary.h and 52 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.
- 8
Load the HEX file
In Proteus double-click the microcontroller, set Program File to DK52_Class_Poll.hex and run the simulation. For real hardware, flash the same file with your programmer.
- 9
Open the example simulation
Open nRF52-DK-BLE-Class-Poll.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.
- 10
Follow the tutorial
nRF52 DK Library for Proteus: nRF52832 Bluetooth LE Simulation explains every connection and setting in order; keep it open beside the files while you build.
FAQs9 questionsContact TEP
How do I download nRF52 DK Library for Proteus V1.0?
Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.
What is inside the archive?
nRF52 DK Library for Proteus V1.0 comes as a ZIP archive of 311 files (3.2 MB, 7.3 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code. Open the File Structure tab for the full list of 311 files.
What should I do if the download does not start?
Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.
Is this file free?
Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.
How do I check that the file arrived complete?
Compare its SHA-256 with the one on this page, f80611d4927064d3579528a2585cfac87d176e5a29c9225eed4316c1201197cc. In PowerShell run Get-FileHash "d5bafb599d5844309b76d6b1a98f0fce.zip"; on macOS or Linux run shasum -a 256 "d5bafb599d5844309b76d6b1a98f0fce.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.
Do I need WinRAR to open the ZIP file?
No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.
Where do I put the LIB and IDX files?
Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.
Which Proteus version does the library need?
The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.
How do I get the HEX file into the simulation?
Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.
Members skip the wait. Log in or join TEP.
- 0Total downloads
- 4%Popularity
- ProteusCategory
- 0Comments
- ssyedzainnasirUploaded by
- 20 Nov 2026Uploaded at
f80611d4927064d3579528a2585cfac87d176e5a29c9225eed4316c1201197cc






















Comments
0