Project Files of PSoC 6 WiFi-BT Pioneer Kit Library for Proteus: Wi-Fi Simulation
4a2d9a7a52e64f3cb3042c811ee684f1.zip

PSoC 6 WiFi-BT Pioneer Kit Library for Proteus V1.0
PSoC 6 WiFi-BT Pioneer Kit Library for Proteus V1.0 comes as a ZIP archive of 307 files (3.2 MB, 7.3 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code.
- LIBProteus library
- DLLProteus model
- DSNProteus simulation
- INOArduino sketch
- LIBArduino library
- HEXHEX firmware
- SRCSource code
Description
PSoC-6-WiFi-BT-Pioneer-Kit-Library-for-Proteus-v1.0.zip with Infineon's PSoC 6 WiFi-BT Pioneer Kit in Proteus (your sketch with D0 .. D15, A0 .. A5, LED8, LED9, the RGB LED, SW2, Wi-Fi to a phone, Bluetooth LE and a serial monitor; TEPPSOC6.LIB, TEPNET.DLL and the TEP Boards for Proteus add-on 1.77.0), the phone library, the mood lamp demo with its sketch and a README.
File Structure
4.2 KB1.1 KB7.7 KB11 KB8.5 KB1.5 KB1.7 KB1.9 KB5.7 KB4.9 KB1.1 KB5.8 KB9.6 KB7.2 KB2.5 KB2.1 KB1.9 KB2.1 KB4.4 KB1.1 KB3 KB3 KB1.8 KB2.5 KB3.5 KB149 B2.7 KB2 KB6.4 KB3.2 KB1.3 KB963 B8.6 KB5.9 KB6 KB12 KB1.6 KB1.3 KB14.7 KB4.3 KB6.1 KB20.1 KB8.2 KB2 KB4.5 KB311 B12.8 KB6.7 KB6.1 KB2.2 KB3.4 KB5.9 KB1.5 KB1.6 KB16.6 KB9.7 KB6.9 KB2.1 KB533 B5.7 KB7.4 KB514 B1.7 KB896 B481 B1.4 KB1012 B482 B936 B559 B467 B3.6 KB3.8 KB504 B956 B575 B455 B8.3 KB10.9 KB522 B79 B5.5 KB3.1 KB79 B442 B918 B1.4 KB1.8 KB1 KB1.3 KB1.4 KB1.8 KB1.4 KB5.7 KB502 B463 B5 KB6.5 KB3.4 KB3.4 KB500 B1.6 KB368 B406 B466 B404 B444 B460 B477 B739 B448 B1.3 KB350 B5.7 KB4 KB562 B1.5 KB2 KB550 B7.2 KB4.1 KB371 B4.5 KB3.5 KB492 B390 B478 B6.6 KB2.4 KB479 B5.1 KB1.9 KB1.3 KB1.3 KB750 B1.3 KB490 B2.2 KB1.9 KB498 B1.2 KB1.2 KB487 B5.1 KB4.6 KB371 B3.6 KB2.5 KB534 B1.5 KB1.2 KB478 B6.2 KB3 KB1.5 KB1.7 KB469 B1 KB1.7 KB433 B294 B358 B1.3 KB2.5 KB13.2 KB3.8 KB659 B510 B4.4 KB1.9 KB5.8 KB11 KB835 B518 B308 B1.3 KB3.3 KB568 B6.4 KB2.3 KB29 B436 B9.2 KB4.9 KB439 B4.2 KB1.5 KB9.3 KB7.1 KB4.7 KB2.4 KB388 B5.1 KB893 B667 B1.3 KB5.5 KB2.3 KB1.8 KB468 B882 B530 B791 B487 B894 B2 KB730 B646 B2.6 KB977 B702 B20.6 KB1.8 KB11.8 KB3.2 KB596 B406 B6.3 KB5.7 KB9.3 KB7.7 KB7.7 KB6.1 KB5.8 KB5.9 KB6.4 KB6.4 KB5.3 KB5.6 KB5.7 KB7.9 KB7.7 KB6.5 KB6.3 KB6.2 KB5.9 KB10.3 KB8.5 KB6.6 KB7.6 KB6.7 KB6.1 KB6.7 KB8.3 KB6.2 KB7.2 KB6.2 KB5.9 KB5.6 KB5.7 KB6.7 KB5.9 KB6.2 KB6 KB6 KB6.1 KB6.3 KB6 KB6.1 KB6.2 KB6 KB5.8 KB6.4 KB6.4 KB6.9 KB6 KB6.8 KB7 KB6.3 KB6.4 KB6.5 KB6.5 KB6.6 KB6.5 KB5.9 KB6.1 KB5.6 KB6.6 KB5.9 KB7.5 KB3.8 KB5.4 KB7.7 KB7.1 KB5.8 KB5.9 KB5.9 KB6.9 KB5.7 KB5.9 KB5.5 KB5.5 KB7.1 KB5.2 KB37.7 KB25.9 KB1.3 KB8.5 KB36.5 KB39.5 KB13.1 KB33 KB2.9 MB17.1 KB36.2 KB2.9 MB11.2 KBGallery12 images from the tutorialOpen the tutorial
The circuit, the board and the results as they appear in PSoC 6 WiFi-BT Pioneer Kit Library for Proteus: Wi-Fi Simulation. Open an image for its full size.












README
PSOC 6 WIFI-BT PIONEER KIT LIBRARY FOR PROTEUS - V1.0 (YOUR ARDUINO SKETCH, WI-FI, BLUETOOTH LE, LEDS AND SW2)
Designed by The Engineering Projects
www.TheEngineeringProjects.com
IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
https://www.theengineeringprojects.com/2026/11/psoc-6-wifi-bt-pioneer-kit-library-for-proteus.html
Report a bug or suggest a feature (our forum):
https://www.theengineeringprojects.com/forum
The demo's phone is our Mobile WiFi Monitor (included) - its article:
https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
Support us (the libraries are free):
https://www.theengineeringprojects.com/donate
FILE STRUCTURE
PSoC-6-WiFi-BT-Pioneer-Kit-TEP-v1.0/
|-- Proteus Library Files/
| |-- TEPLAPTOP.LIB 39.5 KB the laptop (demo), to LIBRARY
| |-- TEPMOBILE.LIB 13.1 KB the phone (demo), to LIBRARY
| |-- TEPPSOC6.LIB 33.0 KB the PSoC 6 WiFi-BT Pioneer Kit, to LIBRARY
|-- Proteus Model Files/
| |-- TEPNET.DLL 2.94 MB the board + monitors + network, to MODELS
|-- Arduino Code/
| |-- PSoC6_Mood_Lamp/PSoC6_Mood_Lamp.ino 4.2 KB the demo sketch
| |-- TEP Boards for Proteus/hardware/ 1.24 MB the Arduino IDE add-on 1.77.0 (298 files)
|-- Proteus Simulation/
| |-- PSoC6_Mood_Lamp.hex 36.2 KB the demo sketch (U1)
| |-- PSoC6-WiFi-Mood-Lamp.pdsprj 17.1 KB the demo: a Wi-Fi mood lamp
| |-- TEPNET.DLL 2.94 MB copy of the model
|-- README.txt ~11.3 KB this file
Total: 7.27 MB (unzipped). The source code of the models is not included.
WHAT IS IT?
Proteus 8 has no PSoC 6 model, so this is NOT a real PSoC 6. Our team has put a lot of effort into building this board
ourselves: it is Infineon's PSoC 6 WiFi-BT Pioneer Kit (CY8CKIT-062-WIFI-BT) - the navy board with the PSoC 62
(CY8C6247: an Arm Cortex-M4 at 150 MHz and a Cortex-M0+), the Murata Type 1DX module (the CYW4343W: Wi-Fi 802.11n and
Bluetooth 5.0) with its chip antenna, the KitProg programmer and its USB, LED8, LED9, the RGB LED, SW2, RESET, the
CAPSENSE slider and buttons and the Arduino Uno R3 headers - drawn compact, and it runs YOUR Arduino sketch in Proteus:
* You write a normal sketch with Arduino-style names (D0 .. D15, A0 .. A5, LED8, LED9, LED_RED / LED_GREEN /
LED_BLUE, SW2) and compile it in the Arduino IDE with our board package "TEP Boards for Proteus" 1.77.0 (in Arduino
Code - see INSTALLATION).
* Wi-Fi works through WiFi.h (WiFi.begin() waits for the join, WiFiServer, WiFiClient, WiFiUDP): the board joins our
panel's router, and the phone of our Mobile WiFi Monitor opens the board's pages. Bluetooth LE works through
ArduinoBLE (the board as a peripheral, the phone as the central).
* LED8 (orange), LED9 (red) and each colour of the RGB LED light when their pin is LOW; SW2 reads LOW while pressed.
TEP additions: the KitProg's USB opens the serial monitor (the same window as our TEP Serial Monitor Advance); our PANEL
pad (or a click on the Murata module) opens the Wi-Fi panel; the chip antenna glows with the Wi-Fi.
Limits (say them before you start): your sketch is one program (the M0+ core and Infineon's ModusToolbox are not
modelled). The CAPSENSE slider and buttons, the second (KitProg) button, the microSD socket, the QSPI flash and the TFT
shield of the kit are drawn or not modelled. Your sketch gets 8 KB of RAM in the simulation (the real chip: 288 KB),
about 256 KB of flash, and int is 16 bits in the simulation (use long for big numbers). See MODEL SCOPE AND LIMITS.
ONE DEVICE (search "PSOC" in Pick Devices):
CY8CKIT-062-WIFI-BT "PSoC 6 WiFi-BT Pioneer Kit" V1.0 (Microprocessor ICs > Wi-Fi Boards), prefix U, model
TEPNET.DLL. Its TEP windows have no Windows title bar: the serial monitor (the USB, 115200 baud) and the Wi-Fi panel
"TEP PSoC 6 WiFi-BT - U1".
The same TEPNET.DLL also runs our other sketch boards and the phone; it replaces any older TEPNET.DLL (keep only this
newest one in MODELS).
TEST STATUS
V1.0: verified in Proteus 8.5 on 17 Nov 2026 with the demo project as shipped. What the Proteus run showed:
* PSoC6-WiFi-Mood-Lamp: "Wi-Fi connected, IP 192.168.1.101", "Lamp page: http://192.168.1.101/", LED8 on; the phone's
Go opened the page (the lamp OFF, RED / GREEN / BLUE / PURPLE / WHITE / OFF links and REFRESH).
* The page's RED: ">> Lamp RED (from the phone)", the RGB LED red and LED9 on; BLUE, then PURPLE (red + blue) the same.
* SW2 on the board: ">> Lamp WHITE (SW2)", the RGB LED white, LED9 off; REFRESH showed WHITE, set from the board, 4
changes. OFF and GREEN from the phone: both printed, the LED followed.
* about 32 s of simulation, no errors, with the phone and the monitor open.
INSTALLATION (about 3 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" to the LIBRARY folder of Proteus, for example:
C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
(on some PCs: C:\ProgramData\Labcenter Electronics\Proteus 8 Professional\LIBRARY). TEPPSOC6.LIB is the board;
TEPMOBILE.LIB and TEPLAPTOP.LIB are the phone and the laptop.
3. Copy the DLLs from "Proteus Model Files" to the MODELS folder (...\Proteus 8 Professional\MODELS) - replace an older
TEPNET.DLL (this one is the first that knows this board).
4. Delete TEPPSOC6.IDX from the LIBRARY folder if it is there.
5. The Arduino IDE (only to compile your own sketches - the demo has its HEX file): copy the folder
"Arduino Code\TEP Boards for Proteus\hardware" into your sketchbook folder (normally Documents\Arduino), so that
Documents\Arduino\hardware\tep\avr\boards.txt exists (replace an older copy); restart the IDE. The Arduino AVR Boards
platform must be installed (it comes with IDE 1.8.x; in IDE 2.x install "Arduino AVR Boards" from the Boards
Manager once).
Tools > Board > TEP Boards for Proteus > Infineon PSoC 6 WiFi-BT Pioneer Kit (TEP Proteus). WiFi and ArduinoBLE are
in the board package.
6. Start Proteus. In Pick Devices (P) search "PSOC".
RUN THE DEMO
Keep the .hex file and the DLLs beside the project in "Proteus Simulation".
PSoC6-WiFi-Mood-Lamp.pdsprj - U1 the Pioneer Kit (PSoC6_Mood_Lamp.hex) is a mood lamp: its RGB LED is the lamp, LED8
shows the Wi-Fi link and LED9 lights while the colour was chosen on the phone; MOB1 = the phone, its browser's home page
is the board's page.
Press Run. The monitor prints "Wi-Fi connected, IP 192.168.1.101" and the page's address; LED8 lights. On the phone
press Go: the page with RED, GREEN, BLUE, PURPLE, WHITE and OFF. Click a colour: the RGB LED takes it, LED9 lights and
the monitor prints ">> Lamp RED (from the phone)". Click SW2 on the board: the next colour, "(SW2)", LED9 off. The
page's REFRESH shows the colour, where it came from and the number of changes.
Closed a window? The USB opens the monitor, the PANEL pad the Wi-Fi panel, a click on the phone's screen the phone.
THE PINS (the label on the board, the core's number, what it can do in the simulation)
D0 .. D13 0 .. 13 GPIO, PWM (analogWrite), interrupt; D0 / D1 Serial1 RX / TX; D10 .. D13 SPI SS / MOSI
/ MISO / SCK
SDA, SCL 14, 15 Wire SDA / SCL (D14 / D15), or GPIO
A0 .. A5 16 .. 21 analogRead 0 .. 1023 for 0 .. 3.3 V, or GPIO
3V3, 5V, GND, RESET 3.3 V (the logic), 5 V, ground, the board's reset; AREF, VIN drawn, not modelled
LED8 / LED9 (22 / 23) and LED_RED / LED_GREEN / LED_BLUE (24 / 25 / 26) light when LOW; LED_BUILTIN is LED8. SW2 (27,
also USER_BTN) reads LOW while you hold it (click it on the board). Serial is the KitProg's USB: the board's built-in
monitor. The Wi-Fi / Bluetooth module is inside the board (not on the header pins).
PROPERTIES (double-click the part > Edit Properties)
PROGRAM the sketch's HEX (Arduino IDE: Sketch > Export Compiled Binary, board Infineon PSoC 6 WiFi-BT ...)
WIFISSID the router's name the board sees (TEP-WiFi); WIFIPASS its password (12345678)
MONITOR YES = the built-in serial monitor on Serial; BAUD its speed (115200, or AUTO)
AUTOOPEN YES = the monitor window opens at Run (the demo: YES)
TIME the clock for NTP: PC, or a fixed UTC time
TROUBLESHOOTING
* "retrying...": the SSID or the password in the sketch differs from WIFISSID / WIFIPASS.
* The phone shows nothing: press Go after the page's address is printed; the sketch must call server.begin().
* The LED looks inverted: LED8, LED9 and the RGB LED light when their pin is LOW.
* SW2 does nothing: use pinMode(SW2, INPUT_PULLUP) and read LOW as pressed.
* An integer goes wrong above 32767: int is 16 bits in the simulation - use long.
BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot and the Serial Monitor text:
https://www.theengineeringprojects.com/forum
LICENCES AND THIRD-PARTY NOTES
* The board model (TEPNET.DLL) and the symbols and artwork (TEPPSOC6.LIB) are made by The Engineering Projects. The
source code of the models is not included.
* TEP Boards for Proteus (Arduino Code): its core, the variants and the EEPROM, SPI and Wire libraries are modified
copies of the Arduino AVR core 1.8.6 - GNU Lesser General Public License 2.1 (LGPL 2.1, the text:
LICENSE-LGPL-2.1.txt); its WiFi, ArduinoBLE and the others and our core files are MIT (LICENSE-MIT.txt).
* Proteus is a product of Labcenter Electronics and is not included. PSoC, CAPSENSE and ModusToolbox are names of
Infineon Technologies, Murata of Murata, Arduino of Arduino. The Bluetooth word mark belongs to Bluetooth SIG. This
library is not made or endorsed by them or by Labcenter.
REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied. Install TEP Boards for Proteus (INSTALLATION step 5), open Arduino Code\PSoC6_Mood_Lamp,
select Infineon PSoC 6 WiFi-BT Pioneer Kit (TEP Proteus) and use Sketch > Export Compiled Binary. On a real kit the
same logic is written with ModusToolbox (the Wi-Fi Connection Manager and an HTTP server) - the pins are the same:
LED8 P1_5, LED9 P13_7, the RGB LED P0_3 / P1_1 / P11_1, SW2 P0_4. Its pins work at 3.3 V.
MODEL SCOPE AND LIMITS
Modelled: D0 .. D15 and A0 .. A5; digital I/O, analogRead 0 .. 1023, PWM (analogWrite), tone and attachInterrupt
through the board model; Serial (the board's monitor), Serial1, Wire and SPI; LED8, LED9, the RGB LED, SW2 and RESET;
Wi-Fi (station, TCP, UDP, DNS, NTP) and Bluetooth LE as a peripheral, with the phone and the laptop of the TEP network.
Not modelled: the PSoC 6 itself, the M0+ core, CAPSENSE, the KitProg's own buttons, microSD, QSPI flash, the TFT shield
and USB device. The simulation runs below real time.
VERSION
TEP PSoC 6 WiFi-BT Pioneer Kit library V1.0 (Nov 2026). Device CY8CKIT-062-WIFI-BT (TEPPSOC6.LIB / TEPNET.DLL), TEP
Boards for Proteus 1.77.0 (adds this board: WiFi, ArduinoBLE, D0 .. D15, A0 .. A5, LED8 / LED9, the RGB LED, SW2).
Demo sketch PSoC6_Mood_Lamp V1.0. Demo part: MOBILE WIFI MONITOR.Development1 release
-
V1.0PSoC 6 WiFi-BT Pioneer Kit Library for Proteus V1.0this page
V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.
Installation10 steps
From the download to a working project, in order. The steps follow what the package contains.
You will need
- Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
- Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
- The compiler named in the tutorialto build the source files into firmware
- Any archive toolWindows, macOS and Linux extract ZIP files on their own
Steps
- 1
Extract the archive
Right-click 4a2d9a7a52e64f3cb3042c811ee684f1.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (PSoC-6-WiFi-BT-Pioneer-Kit-TEP-v1.0) as it is.
- 2
Copy the library files into Proteus
Move TEPLAPTOP.LIB, TEPMOBILE.LIB and TEPPSOC6.LIB and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.
- 3
Add the simulation model
Copy TEPNET.DLL into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.
- 4
Restart Proteus and place the component
Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.
- 5
Install the Arduino library
In the Arduino IDE choose Sketch → Include Library → Add .ZIP Library and pick the library, or copy its folder into Documents\Arduino\libraries. Restart the IDE to see its examples.
- 6
Open the sketch in the Arduino IDE
Open PSoC6_Mood_Lamp.ino, eeprom_clear.ino and eeprom_crc.ino and 17 more, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.
- 7
Build the source code
Open abi.cpp, Arduino.h and binary.h and 52 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.
- 8
Load the HEX file
In Proteus double-click the microcontroller, set Program File to PSoC6_Mood_Lamp.hex and run the simulation. For real hardware, flash the same file with your programmer.
- 9
Open the example simulation
Open PSoC6-WiFi-Mood-Lamp.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.
- 10
Follow the tutorial
PSoC 6 WiFi-BT Pioneer Kit Library for Proteus: Wi-Fi Simulation explains every connection and setting in order; keep it open beside the files while you build.
FAQs9 questionsContact TEP
How do I download PSoC 6 WiFi-BT Pioneer Kit Library for Proteus V1.0?
Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.
What is inside the archive?
PSoC 6 WiFi-BT Pioneer Kit Library for Proteus V1.0 comes as a ZIP archive of 307 files (3.2 MB, 7.3 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code. Open the File Structure tab for the full list of 307 files.
What should I do if the download does not start?
Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.
Is this file free?
Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.
How do I check that the file arrived complete?
Compare its SHA-256 with the one on this page, 0bc9c3057a2088604b59669347034b2385d7deb771132de92e39ed9940a81047. In PowerShell run Get-FileHash "4a2d9a7a52e64f3cb3042c811ee684f1.zip"; on macOS or Linux run shasum -a 256 "4a2d9a7a52e64f3cb3042c811ee684f1.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.
Do I need WinRAR to open the ZIP file?
No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.
Where do I put the LIB and IDX files?
Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.
Which Proteus version does the library need?
The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.
How do I get the HEX file into the simulation?
Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.
Members skip the wait. Log in or join TEP.
- 0Total downloads
- 4%Popularity
- ProteusCategory
- 0Comments
- ssyedzainnasirUploaded by
- 20 Nov 2026Uploaded at
0bc9c3057a2088604b59669347034b2385d7deb771132de92e39ed9940a81047






















Comments
0