Project Files of Feather nRF52840 Express Library for Proteus: Bluetooth Simulation
e91f2a874d734f7d83c04567ec21e804.zip

Feather nRF52840 Express Library for Proteus V1.0
Feather nRF52840 Express Library for Proteus V1.0 comes as a ZIP archive of 308 files (3.2 MB, 7.3 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code.
- LIBProteus library
- DLLProteus model
- DSNProteus simulation
- INOArduino sketch
- LIBArduino library
- HEXHEX firmware
- SRCSource code
Description
Feather-nRF52840-Express-Library-for-Proteus-v1.0.zip with Adafruit's Feather nRF52840 Express in Proteus (your sketch with D0 .. D13, A0 .. A5, the red LED, the blue CONN LED, the USER switch, Bluetooth LE to a phone and a serial monitor; TEPFTH52.LIB, TEPNET.DLL and the TEP Boards for Proteus add-on 1.78.0), the phone library, the reaction timer demo with its sketch and a README.
File Structure
3.9 KB1.1 KB7.7 KB11 KB8.5 KB1.5 KB1.7 KB1.9 KB5.7 KB4.9 KB1.1 KB5.8 KB9.6 KB7.2 KB2.5 KB2.1 KB1.9 KB2.1 KB4.4 KB1.1 KB3 KB3 KB1.8 KB2.5 KB3.5 KB149 B2.7 KB2 KB6.4 KB3.2 KB1.3 KB963 B8.6 KB5.9 KB6 KB12 KB1.6 KB1.3 KB14.7 KB4.3 KB6.1 KB20.1 KB8.2 KB2 KB4.5 KB311 B12.8 KB6.7 KB6.1 KB2.2 KB3.4 KB5.9 KB1.5 KB1.6 KB16.6 KB9.7 KB6.9 KB2.1 KB533 B5.7 KB7.4 KB514 B1.7 KB896 B481 B1.4 KB1012 B482 B936 B559 B467 B3.6 KB3.8 KB504 B956 B575 B455 B8.3 KB10.9 KB522 B79 B5.5 KB3.1 KB79 B442 B918 B1.4 KB1.8 KB1 KB1.3 KB1.4 KB1.8 KB1.4 KB5.7 KB502 B463 B5 KB6.5 KB3.4 KB3.4 KB500 B1.6 KB368 B406 B466 B404 B444 B460 B477 B739 B448 B1.3 KB350 B5.7 KB4 KB562 B1.5 KB2 KB550 B7.2 KB4.1 KB371 B4.5 KB3.5 KB492 B390 B478 B6.6 KB2.4 KB479 B5.1 KB1.9 KB1.3 KB1.3 KB750 B1.3 KB490 B2.2 KB1.9 KB498 B1.2 KB1.2 KB487 B5.1 KB4.6 KB371 B3.6 KB2.5 KB534 B1.5 KB1.2 KB478 B6.2 KB3 KB1.5 KB1.7 KB469 B1 KB1.7 KB433 B294 B358 B1.3 KB2.5 KB13.2 KB3.8 KB659 B510 B4.4 KB1.9 KB5.8 KB11 KB835 B518 B308 B1.3 KB3.3 KB568 B6.4 KB2.3 KB29 B436 B9.2 KB4.9 KB439 B4.2 KB1.5 KB9.3 KB7.1 KB4.7 KB2.4 KB388 B5.1 KB893 B667 B1.3 KB5.5 KB2.3 KB1.8 KB468 B882 B530 B791 B487 B894 B2 KB730 B646 B2.6 KB977 B702 B20.6 KB1.8 KB11.8 KB3.2 KB596 B406 B6.3 KB5.7 KB9.3 KB7.7 KB7.7 KB6.1 KB5.8 KB5.9 KB6.4 KB6.4 KB5.3 KB5.6 KB5.7 KB7.9 KB7.7 KB6.5 KB6.3 KB6.2 KB6.4 KB5.9 KB10.3 KB8.5 KB6.6 KB7.6 KB6.7 KB6.1 KB6.7 KB8.3 KB6.2 KB7.2 KB6.2 KB5.9 KB5.6 KB5.7 KB6.7 KB5.9 KB6.2 KB6 KB6 KB6.1 KB6.3 KB6 KB6.1 KB6.2 KB6 KB5.8 KB6.4 KB6.4 KB6.9 KB6 KB6.8 KB7 KB6.3 KB6.4 KB6.5 KB6.5 KB6.6 KB6.5 KB5.9 KB6.1 KB5.6 KB6.6 KB5.9 KB7.5 KB3.8 KB5.4 KB7.7 KB7.1 KB5.8 KB5.9 KB5.9 KB6.9 KB5.7 KB5.9 KB5.5 KB5.5 KB7.1 KB5.2 KB38.3 KB25.9 KB1.3 KB8.5 KB36.6 KB30.6 KB39.5 KB13.1 KB2.9 MB16.6 KB26.9 KB2.9 MB10.9 KBGallery12 images from the tutorialOpen the tutorial
The circuit, the board and the results as they appear in Feather nRF52840 Express Library for Proteus: Bluetooth Simulation. Open an image for its full size.












README
FEATHER NRF52840 EXPRESS LIBRARY FOR PROTEUS - V1.0 (YOUR ARDUINO SKETCH, BLUETOOTH LE, THE LEDS AND THE USER SWITCH)
Designed by The Engineering Projects
www.TheEngineeringProjects.com
IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
https://www.theengineeringprojects.com/2026/11/feather-nrf52840-express-library-for-proteus.html
Report a bug or suggest a feature (our forum):
https://www.theengineeringprojects.com/forum
The demo's phone is our Mobile WiFi Monitor (included; its Bluetooth app) - its article:
https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
Support us (the libraries are free):
https://www.theengineeringprojects.com/donate
FILE STRUCTURE
Feather-nRF52840-Express-TEP-v1.0/
|-- Proteus Library Files/
| |-- TEPFTH52.LIB 30.6 KB the Feather nRF52840 Express, to LIBRARY
| |-- TEPLAPTOP.LIB 39.5 KB the laptop (demo), to LIBRARY
| |-- TEPMOBILE.LIB 13.1 KB the phone (demo), to LIBRARY
|-- Proteus Model Files/
| |-- TEPNET.DLL 2.94 MB the board + monitors + network, to MODELS
|-- Arduino Code/
| |-- Feather_Reaction_Timer/Feather_Reaction_Timer.ino 3.9 KB the demo sketch
| |-- TEP Boards for Proteus/hardware/ 1.24 MB the Arduino IDE add-on 1.78.0 (299 files)
|-- Proteus Simulation/
| |-- Feather_Reaction_Timer.hex 26.9 KB the demo sketch (U1)
| |-- Feather-BLE-Reaction-Timer.pdsprj 16.6 KB the demo: a Bluetooth LE reaction timer
| |-- TEPNET.DLL 2.94 MB copy of the model
|-- README.txt ~11.1 KB this file
Total: 7.27 MB (unzipped). The source code of the models is not included.
WHAT IS IT?
Proteus 8 has no nRF52840 model, so this is NOT a real nRF52840. Our team has put a lot of effort into building this
board ourselves: it is Adafruit's Feather nRF52840 Express - the black Feather (2.0 x 0.9 in) with Nordic's nRF52840
(an Arm Cortex-M4F at 64 MHz with Bluetooth LE and native USB) in its module, the 2 MB QSPI flash, the micro-USB, the
JST battery socket, the red LED (D3), the blue CONN LED (D4), the NeoPixel, the USER switch, RESET and the 16 + 12
Feather pins - drawn compact, and it runs YOUR Arduino sketch in Proteus:
* You write a normal sketch with the names of Adafruit's nRF52 core (D0 .. D13, A0 .. A5, LED_RED, LED_BLUE /
LED_CONN, LED_BUILTIN, PIN_BUTTON1, PIN_NEOPIXEL) and compile it in the Arduino IDE with our board package "TEP
Boards for Proteus" 1.78.0 (in Arduino Code - see INSTALLATION).
* Bluetooth LE works through Adafruit's Bluefruit library (bluefruit.h: Bluefruit, BLEUart, BLEDis, BLEBas) or
ArduinoBLE, with the board as a peripheral and the phone of our Mobile WiFi Monitor as the central: the phone's
Bluetooth app scans, connects and shows the lines the board sends.
* The red LED and the blue CONN LED light when their pin is HIGH; Bluefruit.autoConnLed() lights the blue LED while
the phone is connected, as on the real board. The USER switch reads LOW while pressed (INPUT_PULLUP).
TEP additions: the micro-USB opens the serial monitor (the same window as our TEP Serial Monitor Advance).
Limits (say them before you start): the NeoPixel is drawn, not modelled in V1.0 (use the red and blue LEDs); the QSPI
flash, the battery charger, NFC, USB HID and the central role of Bluetooth are not modelled. Your sketch gets 8 KB of
RAM in the simulation (the real chip: 256 KB), about 256 KB of flash, and int is 16 bits in the simulation (use long
for big numbers). See MODEL SCOPE AND LIMITS.
ONE DEVICE (search "FEATHER" in Pick Devices):
FEATHER NRF52840 EXPRESS "Feather nRF52840 Express" V1.0 (Microprocessor ICs > Bluetooth Boards), prefix U, model
TEPNET.DLL. Its TEP window has no Windows title bar: the serial monitor (the micro-USB, 115200 baud).
The same TEPNET.DLL also runs our other sketch boards and the phone; it replaces any older TEPNET.DLL (keep only this
newest one in MODELS).
TEST STATUS
V1.0: verified in Proteus 8.5 on 17 Nov 2026 with the demo project as shipped. What the Proteus run showed:
* Feather-BLE-Reaction-Timer: "Advertising as "Feather Reaction""; the phone's Bluetooth app, SCAN, connect: "Phone
connected", the blue CONN LED on.
* USER: ">> Get ready...", a random wait, ">> GO!" with the red LED on; USER: ">> Round 1: 772 ms NEW BEST"; round 2:
262 ms (the new best); round 3: 538 ms (best 262 ms). The phone showed every line.
* USER during the wait: ">> Too soon! Press USER to try again".
* about 32 s of simulation, no errors, with the phone and the monitor open.
INSTALLATION (about 3 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" to the LIBRARY folder of Proteus, for example:
C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
(on some PCs: C:\ProgramData\Labcenter Electronics\Proteus 8 Professional\LIBRARY). TEPFTH52.LIB is the board;
TEPMOBILE.LIB and TEPLAPTOP.LIB are the phone and the laptop.
3. Copy the DLLs from "Proteus Model Files" to the MODELS folder (...\Proteus 8 Professional\MODELS) - replace an older
TEPNET.DLL (this one is the first that knows this board).
4. Delete TEPFTH52.IDX from the LIBRARY folder if it is there.
5. The Arduino IDE (only to compile your own sketches - the demo has its HEX file): copy the folder
"Arduino Code\TEP Boards for Proteus\hardware" into your sketchbook folder (normally Documents\Arduino), so that
Documents\Arduino\hardware\tep\avr\boards.txt exists (replace an older copy); restart the IDE. The Arduino AVR Boards
platform must be installed (it comes with IDE 1.8.x; in IDE 2.x install "Arduino AVR Boards" from the Boards
Manager once).
Tools > Board > TEP Boards for Proteus > Adafruit Feather nRF52840 Express (TEP Proteus). Bluefruit and ArduinoBLE
are in the board package.
6. Start Proteus. In Pick Devices (P) search "FEATHER".
RUN THE DEMO
Keep the .hex file and TEPNET.DLL beside the project in "Proteus Simulation".
Feather-BLE-Reaction-Timer.pdsprj - U1 the Feather (Feather_Reaction_Timer.hex) is a reaction timer; MOB1 = the phone
(Mobile WiFi Monitor), whose Bluetooth app connects to it. No wires: the switch and the LEDs are on the board.
Press Run. The monitor prints "Advertising as "Feather Reaction"". In the phone's Bluetooth app press SCAN and connect
to "Feather Reaction": "Phone connected", the blue CONN LED lights. Click USER: "Get ready...". After a random wait the
red LED lights ("GO!"): click USER again - "Round 1: ... ms (best ... ms)" on the monitor and on the phone. Clicking
during the wait is a false start ("Too soon!"), and a time under 100 ms is a guess ("Too fast").
Closed a window? The micro-USB opens the monitor, a click on the phone's screen the phone.
THE PINS (the label on the board, the core's number, what it can do in the simulation)
TX, RX 0, 1 Serial1 TX / RX, or GPIO
D2, 5, 6, 9 .. 13 GPIO, PWM (analogWrite), interrupt (D2 is the free pin of the Feather row)
A0 .. A5 14 .. 19 analogRead 0 .. 1023 for 0 .. 3.3 V, or GPIO; AREF = A7 (21)
SCK, MO, MI 26, 25, 24 SPI (SS = D5); SDA, SCL 22, 23 Wire
3V, USB, GND, RST 3.3 V (the logic), 5 V (USB), ground, the board's reset; BAT, EN drawn, not modelled
On the board: LED_RED = D3 (LED_BUILTIN) and LED_BLUE = LED_CONN = D4, lit when HIGH (LED_STATE_ON 1); PIN_BUTTON1 = D7,
the USER switch (click it); PIN_NEOPIXEL = D8 (drawn); A6 = PIN_VBAT (the battery divider, reads 0 here). Serial is the
native USB: the board's built-in monitor.
PROPERTIES (double-click the part > Edit Properties)
PROGRAM the sketch's HEX (Arduino IDE: Sketch > Export Compiled Binary, board Adafruit Feather nRF52840 Express)
MONITOR YES = the built-in serial monitor on Serial; BAUD its speed (115200, or AUTO)
AUTOOPEN YES = the monitor window opens at Run (the demo: YES)
TROUBLESHOOTING
* The phone finds nothing: press SCAN after "Advertising as" is printed; the sketch must call
Bluefruit.Advertising.start().
* The phone shows no text: lines go out at their newline (println) or at flush().
* The switch seems dead: use pinMode(PIN_BUTTON1, INPUT_PULLUP) and act on the change to LOW.
* An LED stays dark: LED_RED is D3 and LED_BLUE D4, lit when HIGH.
* An integer goes wrong above 32767: int is 16 bits in the simulation - use long.
BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot and the Serial Monitor text:
https://www.theengineeringprojects.com/forum
LICENCES AND THIRD-PARTY NOTES
* The board model (TEPNET.DLL) and the symbols and artwork (TEPFTH52.LIB) are made by The Engineering Projects. The
source code of the models is not included.
* TEP Boards for Proteus (Arduino Code): its core, the variants and the EEPROM, SPI and Wire libraries are modified
copies of the Arduino AVR core 1.8.6 - GNU Lesser General Public License 2.1 (LGPL 2.1, the text:
LICENSE-LGPL-2.1.txt); its Bluefruit, ArduinoBLE and the others and our core files are MIT (LICENSE-MIT.txt).
* Proteus is a product of Labcenter Electronics and is not included. Adafruit, Feather and NeoPixel are names of
Adafruit Industries, nRF52840 of Nordic Semiconductor, Arduino of Arduino. The Bluetooth word mark belongs to
Bluetooth SIG. This library is not made or endorsed by them or by Labcenter.
REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied. Install TEP Boards for Proteus (INSTALLATION step 5), open Arduino Code\
Feather_Reaction_Timer, select Adafruit Feather nRF52840 Express (TEP Proteus) and use Sketch > Export Compiled Binary.
For a real board install "Adafruit nRF52" from the Boards Manager (Adafruit's board URL) and select Adafruit Feather
nRF52840 Express: the same sketch compiles with Adafruit's Bluefruit. Its pins work at 3.3 V.
MODEL SCOPE AND LIMITS
Modelled: D0 .. D13 and A0 .. A5 (A7 = AREF); digital I/O, analogRead 0 .. 1023, PWM (analogWrite), tone and
attachInterrupt through the board model; Serial (the board's monitor), Serial1, Wire and SPI; the red and blue LEDs, the
USER switch and RESET; Bluetooth LE as a peripheral (Bluefruit's BLEUart / BLEDis / BLEBas, ArduinoBLE) with the phone.
Not modelled: the nRF52840 itself, the NeoPixel, the QSPI flash, the charger, NFC, USB HID and Bluetooth's central role.
The simulation runs below real time.
VERSION
TEP Feather nRF52840 Express library V1.0 (Nov 2026). Device FEATHER NRF52840 EXPRESS (TEPFTH52.LIB / TEPNET.DLL), TEP
Boards for Proteus 1.78.0 (adds this board: Bluefruit, ArduinoBLE, D0 .. D13, A0 .. A7, LED_RED, LED_BLUE, PIN_BUTTON1).
Demo sketch Feather_Reaction_Timer V1.0. Demo part: MOBILE WIFI MONITOR.Development1 release
-
V1.0Feather nRF52840 Express Library for Proteus V1.0this page
V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.
Installation10 steps
From the download to a working project, in order. The steps follow what the package contains.
You will need
- Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
- Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
- The compiler named in the tutorialto build the source files into firmware
- Any archive toolWindows, macOS and Linux extract ZIP files on their own
Steps
- 1
Extract the archive
Right-click e91f2a874d734f7d83c04567ec21e804.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (Feather-nRF52840-Express-TEP-v1.0) as it is.
- 2
Copy the library files into Proteus
Move TEPFTH52.LIB, TEPLAPTOP.LIB and TEPMOBILE.LIB and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.
- 3
Add the simulation model
Copy TEPNET.DLL into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.
- 4
Restart Proteus and place the component
Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.
- 5
Install the Arduino library
In the Arduino IDE choose Sketch → Include Library → Add .ZIP Library and pick the library, or copy its folder into Documents\Arduino\libraries. Restart the IDE to see its examples.
- 6
Open the sketch in the Arduino IDE
Open Feather_Reaction_Timer.ino, eeprom_clear.ino and eeprom_crc.ino and 17 more, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.
- 7
Build the source code
Open abi.cpp, Arduino.h and binary.h and 52 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.
- 8
Load the HEX file
In Proteus double-click the microcontroller, set Program File to Feather_Reaction_Timer.hex and run the simulation. For real hardware, flash the same file with your programmer.
- 9
Open the example simulation
Open Feather-BLE-Reaction-Timer.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.
- 10
Follow the tutorial
Feather nRF52840 Express Library for Proteus: Bluetooth Simulation explains every connection and setting in order; keep it open beside the files while you build.
FAQs9 questionsContact TEP
How do I download Feather nRF52840 Express Library for Proteus V1.0?
Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.
What is inside the archive?
Feather nRF52840 Express Library for Proteus V1.0 comes as a ZIP archive of 308 files (3.2 MB, 7.3 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code. Open the File Structure tab for the full list of 308 files.
What should I do if the download does not start?
Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.
Is this file free?
Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.
How do I check that the file arrived complete?
Compare its SHA-256 with the one on this page, 7d5c7bd416e028b80ba4f20fa3829cbf8bec57c0bd319e1b6f61535f039766a5. In PowerShell run Get-FileHash "e91f2a874d734f7d83c04567ec21e804.zip"; on macOS or Linux run shasum -a 256 "e91f2a874d734f7d83c04567ec21e804.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.
Do I need WinRAR to open the ZIP file?
No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.
Where do I put the LIB and IDX files?
Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.
Which Proteus version does the library need?
The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.
How do I get the HEX file into the simulation?
Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.
Members skip the wait. Log in or join TEP.
- 0Total downloads
- 4%Popularity
- ProteusCategory
- 0Comments
- ssyedzainnasirUploaded by
- 20 Nov 2026Uploaded at
7d5c7bd416e028b80ba4f20fa3829cbf8bec57c0bd319e1b6f61535f039766a5






















Comments
0