Project Files of Closed-Loop BLDC Speed Control on Raspberry Pi 5 (Proteus Simulation)
8d17d747a1564745a0002ec7ec02405d.zip

Closed-Loop BLDC Speed Control on Raspberry Pi 5 in Proteus Simulation V1.0
Closed-Loop BLDC Speed Control on Raspberry Pi 5 in Proteus Simulation V1.0 comes as a ZIP archive of 135 files (13.3 MB, 25.8 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, source code and a nested archive.
- LIBProteus library
- DLLProteus model
- DSNProteus simulation
- SRCSource code
- ZIPNested archive
Description
Raspberry-Pi-5-BLDC-Motor-Speed-Control-ZS-X11H-Proteus-Simulation-v1.0.zip: the complete Proteus simulation project (Raspberry Pi 5, the ZS-X11H driver, the 42BLF Hall BLDC motor, the Laptop and Mobile WiFi Monitors), the Python program bldc_speed.py, every LIB and DLL the simulation needs, the TEPPi Python runtime and a README.
File Structure
12.9 KB39.5 KB13.1 KB60.5 KB18.3 KB3.3 MB34.3 KB620.8 KB36 KB169.8 KB628.1 KB99.3 KB65.3 KB4.8 MB4.1 MB80 B97.8 KB26.8 KB1.2 MB1.1 MB88.9 KB27.3 KB55.8 KB79.8 KB105.8 KB193.8 KB113.8 KB48.8 KB145.8 KB36.8 KB29.3 KB42.3 KB28.8 KB67.3 KB89.3 KB153.8 KB22.8 KB38.8 KB2.1 KB9.9 KB4.1 KB1.3 KB4.7 KB431 B2.5 KB17.5 KB283 B6.5 KB37.9 KB11.1 KB5.5 KB885 B13.6 KB9 KB878 B1.5 KB4 KB1004 B10 B110 B2.6 KB1.1 KB8.9 KB58.5 KB12.4 KB6.6 KB18.5 KB20.7 KB27.8 KB21.1 KB7.1 KB7.7 KB2.7 KB51.2 KB100.9 KB1.2 KB24.3 KB7.4 KB53.6 KB26.1 KB20.5 KB60.5 KB19.6 KB1.6 KB8.4 KB20.9 KB2.6 KB539 B1.4 KB9.7 KB2.8 KB21 B92 B7.9 KB264 B3.4 KB3.8 KB17.5 KB55.2 KB3.3 KB10.8 KB1.5 KB4.2 KB7.3 KB2.5 KB32.6 KB14.5 KB283 B17.4 KB257 B691 B14.5 KB12.8 KB3.6 KB1.7 KB37 KB418 B6.2 KB7 KB37.3 KB10.6 KB23.7 KB28.7 KB8.8 KB16.9 KB305.5 KB2.9 MB311 KB10.3 KB29.9 KB305.5 KB2.9 MB311 KB10.4 KB8.7 KBGallery12 images from the tutorialOpen the tutorial
The circuit, the board and the results as they appear in Closed-Loop BLDC Speed Control on Raspberry Pi 5 (Proteus Simulation). Open an image for its full size.












README
===============================================================================================================
Closed-Loop BLDC Speed Control on Raspberry Pi 5 (Proteus Simulation) - Project V1.0
The Engineering Projects - www.TheEngineeringProjects.com
===============================================================================================================
IMPORTANT LINKS
The project tutorial (circuit, code, simulation results):
https://www.theengineeringprojects.com/2026/11/raspberry-pi-5-bldc-speed-control-zs-x11h-proteus-simulation.html
The libraries this project is built from (each post has its own full download and tutorial):
Raspberry Pi 5 board:
https://www.theengineeringprojects.com/2026/10/raspberry-pi-5-library-for-proteus.html
ZS-X11H BLDC driver:
https://www.theengineeringprojects.com/2026/11/zs-x11h-bldc-driver-library-for-proteus.html
42BLF Hall BLDC motor:
https://www.theengineeringprojects.com/2026/11/42blf-hall-bldc-motor-library-for-proteus.html
Laptop WiFi Monitor:
https://www.theengineeringprojects.com/2026/10/laptop-wifi-monitor-library-for-proteus.html
Mobile WiFi Monitor:
https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
Support our free work: https://www.theengineeringprojects.com/donate
FILE STRUCTURE
Pi-5-BLDC-Speed-Controller-TEP-v1.0/
|-- Proteus Library Files/
| |-- TEPBLDC42.LIB 12.9 KB a part of the project -> LIBRARY folder
| |-- TEPLAPTOP.LIB 39.5 KB a part of the project -> LIBRARY folder
| |-- TEPMOBILE.LIB 13.1 KB a part of the project -> LIBRARY folder
| |-- TEPRPI5.LIB 60.5 KB a part of the project -> LIBRARY folder
| |-- TEPZSX11H.LIB 18.3 KB a part of the project -> LIBRARY folder
|-- Proteus Model Files/
| |-- TEPBLDC42.DLL 305.5 KB a model -> MODELS folder
| |-- TEPNET.DLL 2.89 MB a model -> MODELS folder
| |-- TEPZSX11H.DLL 311.0 KB a model -> MODELS folder
| |-- TEPPi/python/ 17.54 MB Python 3.11 embeddable -> MODELS\TEPPi (33 files)
| |-- TEPPi/runtime/ 1.11 MB TEP Pi runtime, gpiozero -> MODELS\TEPPi (87 files)
|-- Proteus Simulation/
| |-- bldc_speed.py 10.3 KB the program PI1 runs
| |-- Pi-5-BLDC-Speed-Controller.pdsprj 29.9 KB the project simulation
| |-- TEPBLDC42.DLL 305.5 KB copy of the model
| |-- TEPNET.DLL 2.89 MB copy of the model
| |-- TEPZSX11H.DLL 311.0 KB copy of the model
|-- Python Code/
| |-- bldc_speed.py 10.4 KB the program (the same file)
|-- README.txt ~9.3 KB this file
Total: 25.84 MB (unzipped). The C++ source code of the models is not included.
WHAT IS IT?
A brushless motor speed controller you can run in Proteus: a Raspberry Pi 5 holds the speed of a BLDC motor in a
closed loop through a ZS-X11H driver board - a feed-forward and a PI loop on the speed pulses - with a soft ramp,
a reverse through zero, a brake and a web dashboard, the way a spindle, a fan or a pump controller works.
* ZS-X11H BLDC driver (ZSX11HTEP, U1; POT 0, JUMPER OFF, POLES 8): P = a 1 kHz PWM from GPIO18 (pin 12), DIR from
GPIO23 (pin 16), STOP from GPIO24 (pin 18), BRAKE from GPIO25 (pin 22); SC (the speed pulses) to GPIO17 (pin 11)
- on a real board through a 10k / 20k divider, SC is 5 V; V+ on +24V, V- GND.
* 42BLF Hall BLDC motor (BLDC42BLF01TEP, M1; LOAD 0.02, INERTIA 300 - a small flywheel): U V W from MA MB MC,
its Hall cable (+5V HU HV HW GND) to the driver's Hall connector.
* RASPBERRY PI 5 (PI1) runs bldc_speed.py on Ethernet at 192.168.1.51 (port 8000).
* Laptop WiFi Monitor (PC1) and Mobile WiFi Monitor (MOB1) open http://192.168.1.51:8000/.
The rules (at the top of the program):
* 5 times a second: count SC (12 pulses a turn: 3 x the 4 pole pairs), work out the RPM;
* the set speed ramps at 1500 RPM a second; the duty = 14 % + 0.0153 % a RPM (the feed-forward) + a PI correction
(0.005 % a RPM, 0.06 % a RPM-second, no integration while the duty is at its limit), 0 - 95 %;
* a reverse ramps down to zero, changes DIR below 100 RPM, then ramps up the other way; BRAKE stops it at once;
* a stall (over 30 % duty and no speed for 1.5 s) stops the motor (STOP low).
Its pages:
/ the dashboard: the speed, the direction, the set speed, the duty, SC, the events
/1500 /3000 set the speed (the direction kept) /rev reverse at the same speed
/stop a soft (ramped) stop /brake brake now
/data everything as JSON
No extra Python library: lgpio (in the TEPPi runtime and on Raspberry Pi OS), threading, http.server.
TEST STATUS
Tested in Proteus 8 Professional on Windows 11, the run that made the tutorial's screenshots (the program's times):
- 0.0 s "run: 1500 RPM forward"; 2.4 s "at speed: 1500 RPM forward (duty 37 %)" (SC 300 Hz, 0.27 A from 24 V).
- 13.6 s: 3000 from the laptop; 15.4 s "at speed: 2950 RPM forward (duty 60 %)", then 2975 - 3025 RPM.
- The motor's rated load (0.063 N.m) from its pop-up: 18.6 s "speed dip to 2725 RPM", 2125 RPM at 19.0 s with the duty
at 91 %; 20.0 s "at speed: 2925 RPM forward (duty 85 %)", then 3000 RPM at 84.5 % (67.4 mN.m, 1.91 A in the phases).
- The light load back: the duty down to 58 - 60 % at 3000 RPM.
- 26.0 s: REV from the phone: down through zero, 28.2 s "DIR: reverse (the motor at 0 RPM)", 31.0 s "at speed:
2950 RPM reverse (duty 60 %)".
- 34.3 s: BRAKE from the laptop: 34.8 s "BRAKE: stopped from 2475 RPM in 0.4 s".
- 30390 Hall edges, 0 bad. 38.8 s of simulation in 227 s.
INSTALLATION
1. Close Proteus. Extract the WHOLE zip file, for example to your Desktop.
2. Copy the files from "Proteus Library Files" into the LIBRARY folder of Proteus, for example
C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
3. Copy everything in "Proteus Model Files" - the DLL files and the TEPPi folder - into the MODELS folder (next
to LIBRARY).
4. Start Proteus. Press P in the schematic and search for RASPBERRY PI 5, ZSX11HTEP or BLDC42BLF01TEP to check that
the parts are there.
RUN THE SIMULATION
1. Open "Proteus Simulation\Pi-5-BLDC-Speed-Controller.pdsprj". Keep bldc_speed.py and the DLL files beside it.
2. Press Play. The motor ramps up to 1500 RPM forward and the Pi's terminal prints a line every second.
3. Open the Laptop WiFi Monitor (PC1) or the Mobile WiFi Monitor (MOB1) and press Go: 1500, 3000, REV, STOP, BRAKE.
4. Click the motor for its pop-up and pick a load with its chips (the rated load, 0.063 N.m): watch the duty rise.
Your own program: edit bldc_speed.py.
PROPERTIES USED IN THIS PROJECT
PI1 RASPBERRY PI 5 PROGRAM=bldc_speed.py, ETHERNET=IN (192.168.1.51)
U1 ZSX11HTEP POT=0, JUMPER=OFF, POLES=8
M1 BLDC42BLF01TEP LOAD=0.02, INERTIA=300
PC1, MOB1 HOMEPAGE=http://192.168.1.51:8000/
TROUBLESHOOTING
* The motor does not turn: no +24V on V+, STOP low, or the Hall cable swapped (the driver's pop-up shows bad steps).
* The speed reads 0 while the motor turns: SC not reaching GPIO17.
* The speed overshoots or hunts: lower KP and KI at the top of the program.
* The terminal cannot start Python: the TEPPi folder is not in MODELS.
LICENCES
* The project, the program, the parts (LIB files) and the models (DLL files) are made by The Engineering Projects
and are free for learning and for your own projects. The models use only standard Windows libraries.
The C++ source code of the models is not included; the source code is not included for any model.
* TEPPi\python is the Python 3.11 Windows embeddable package (Python Software Foundation License); TEPPi\runtime
holds our TEP Pi runtime with gpiozero and colorzero (BSD licences) - their licence files are inside the folders.
* Proteus is a product of Labcenter Electronics and is not included. Raspberry Pi is a trademark of Raspberry Pi
Ltd. This project is not made or endorsed by them or by the makers of the ZS-X11H and the 42BLF motor.
VERSION
V1.0 - the first release of the project.
===============================================================================================================Development1 release
-
V1.0Closed-Loop BLDC Speed Control on Raspberry Pi 5 in Proteus Simulation V1.0this page
V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.
Installation7 steps
From the download to a working project, in order. The steps follow what the package contains.
You will need
- Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
- Pythonto build the source files into firmware
- Any archive toolWindows, macOS and Linux extract ZIP files on their own
Steps
- 1
Extract the archive
Right-click 8d17d747a1564745a0002ec7ec02405d.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (Pi-5-BLDC-Speed-Controller-TEP-v1.0) as it is.
- 2
Copy the library files into Proteus
Move TEPBLDC42.LIB, TEPLAPTOP.LIB and TEPMOBILE.LIB and 2 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.
- 3
Add the simulation model
Copy TEPBLDC42.DLL, TEPNET.DLL and TEPZSX11H.DLL and 7 more into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.
- 4
Restart Proteus and place the component
Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.
- 5
Build the source code
Open bldc_speed.py, attr.py and color.py and 28 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.
- 6
Open the example simulation
Open Pi-5-BLDC-Speed-Controller.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.
- 7
Follow the tutorial
Closed-Loop BLDC Speed Control on Raspberry Pi 5 (Proteus Simulation) explains every connection and setting in order; keep it open beside the files while you build.
FAQs8 questionsContact TEP
How do I download Closed-Loop BLDC Speed Control on Raspberry Pi 5 in Proteus Simulation V1.0?
Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.
What is inside the archive?
Closed-Loop BLDC Speed Control on Raspberry Pi 5 in Proteus Simulation V1.0 comes as a ZIP archive of 135 files (13.3 MB, 25.8 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, source code and a nested archive. Open the File Structure tab for the full list of 135 files.
What should I do if the download does not start?
Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.
Is this file free?
Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.
How do I check that the file arrived complete?
Compare its SHA-256 with the one on this page, ba9255e87bbf5043b54debb3fe9c20dacdfc85d123ddb173a1f73443673a30d2. In PowerShell run Get-FileHash "8d17d747a1564745a0002ec7ec02405d.zip"; on macOS or Linux run shasum -a 256 "8d17d747a1564745a0002ec7ec02405d.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.
Do I need WinRAR to open the ZIP file?
No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.
Where do I put the LIB and IDX files?
Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.
Which Proteus version does the library need?
The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.
Members skip the wait. Log in or join TEP.
- 0Total downloads
- 4%Popularity
- Raspberry PiCategory
- 0Comments
- ssyedzainnasirUploaded by
- 17 Nov 2026Uploaded at
ba9255e87bbf5043b54debb3fe9c20dacdfc85d123ddb173a1f73443673a30d2






















Comments
0