Hello Learner! I hope you are doing great. Welcome to another tutorial at The Engineering Projects. This blog is the part of series we have stated about the Digital Logic Circuits. Previous to this, we learned Implementation of SK Flip Flops in Proteus. at the present day, we'll seek the knowledge about the following points:
What are Flip Flops?
What are JK Flip Flops?
How can we record the Truth Table of JK Flip Flops?
What is the Procedure to Construct the circuit of JK Flip Flop through Logic Gates and IC circuit?
Moreover, we'll also have some useful bits of Information in Did you know Sections. Let' see the explanation of the concepts given above.
Flip Flops
The Flip Flops are the building blocks of many of the Electronic Circuits. ...
Hello friends! I hope you all will be absolutely fine and having fun. Today, I am going to share my knowledge with all of you about how to make a simple program for DC Motor Direction Control in LabVIEW. In my previous tutorials, I have also worked on DC Motor Direction Control using Arduino. You should go through these tutorials they will be helpful in better understanding of the tutorial DC Motor Direction control using NI LabVIEW. The word DC is basically an abbreviation of Direct current. So, a direct current motor is commonly used motor having two input terminals, one is positive and the other one is negative. If we connect these terminals with the voltage supply the motor will rotate. If you change the polarity then motor will rotate in oppo ...
Thank you for being here for today's tutorial of our in-depth Raspberry Pi programming tutorial. The previous tutorial taught us how to install a PIR sensor on a Raspberry Pi 4 to create a motion detector. However, this tutorial will teach you how to connect a single seven-segment display to a Raspberry Pi 4. In the following sections, we will show you how to connect a Raspberry Pi to a 4-digit Seven-Segment Display Module so that the time can be shown on it.
Seven-segment displays are a simple type of Display that use eight light-emitting diodes to show off decimal numbers. It's common to find it in gadgets like digital clocks, calculators, and electronic meters that show numbers. Raspberry Pi, built around an ARM chip, is widely acknowledged as ...
Hey pupils, welcome to The Engineering Projects. We hope you are doing great. In today's simulation in Proteus ISIS, we'll seek the knowledge of an interesting topic. We are going to design a Television remote jammer in Proteus. We all are familiar with the TV Remote controller device and know it works when a light signal emitted by it is sensed by the television. Have a glance at the topics we will see in detail today:
Introduction to 555 Timer TV Remote Control Jammer.
Components of the circuit.
Working principle of 555 Timer Jammer.
Simulation of the Jammer of TV Remote Control using 555 Timer.
Moreover, you will also learn some interesting facts about the topic in DID YOU KNOW sections. let's jump to our first topic.
555 Timer TV R ...
Hello everyone, I hope you all are fine and having fun with your lives. Today, I am going to share a semester project which is named as Automatic Street Light Project. I have designed this project in Proteus ISIS and the simulation is also given below for download. Btw this was my first project during my engineering course. :D I had really enjoyed while working on this project as I was new to electronics then.
This project is about Automatic Street Light. You must have examined on your streets that the street lights turn ON at night while they turn OFF in the day. When I was a child then I think that someone turns ON the switch in the day and then turns it OFF at night but that's really not the case. :P
In fact, these lights are automatic and have ...
Hello friends, I hope you all are fine and enjoying good health. Today's tutorial, as the name shows, is on Introduction to PLC. PLC is an abbreviation of Programmable Logic Controller. Recently I worked on a project in which I have to design a Automated coffee Mixing Machine Using PLC. It worked quite good and I had a great time while working on it. After completing that project, it occurred to me that I haven't posted any tutorial on PLC. So I thought of starting this tutorial. This tutorial is not gonna cover in single post so my plan is to divide it in parts.
Today. I am gonna give an overview about PLC. We will have a look on basics i.e. what is PLC? Why we use PLC instead of microcontroller like Arduino or PIC Microcontroller? What's its adv ...
Hello friends, hope you all are having fun in your life.
Today's tutorial is about the component designing in Proteus ISIS. This tutorial actually deals with the presentation of your project. Usually when students give presentation of their projects, then it is asked that add the circuit diagram of their project. Now when students open Proteus in order to design their circuit, they found out that the components they have used in their project are not available in the Proteus Directory. Now what to do ?
In that case, there's a need to design your own component in Proteus and place it in the circuit. Although, this new designed component won't work as the real co ...
Hello geeks, welcome to our new project. In this project, we are going to make a very interesting project. I think most of us have seen the scoreboards in sports, after looking at that, have you ever wondered about the working of it. Therefore, this time, we will be making something like that only with some extra features. So basically that score board is nothing but a counter which counts the scores. Most of the geeks who have an electronics background or have ever studied digital electronics must have heard about the counter.
Here, in this project, we are going to make an Up-Down counter. A simple counter counts in increasing or decreasing order but the Up-Down counter counts in increasing and decreasing order, both depending upon the input it h ...
Hello fiends, hope you all are fine and having fun with your lives. In today's tutorial, I am going to share a new project designed in MATLAB and named as Hexapod Simulation in MATLAB. We all know about the Hexapod, its a special kind of robot which has six legs. Hexa is used for six so its quite obvious that hexapod has six legs on it.
I have designed this project on a client's request and today I thought to share it with you guys. Because this Hexapod simulation in MATLAB is designed after a lot of efforts by our TEP team that's why this simulation is not free to download but we have placed a small price on it so that engineering students can buy it easily. So, let's get started with Hexapod Simulation in MATLAB.
Hexapod Simulation in MATLAB
...
Buy This Project
Hello friends, I hope you are doing great. Today, I am going to share an expert level project which is ECG Averaging in MATLAB. If you are new to ECG then you should have a look at Introduction to ECG. I have already shared ECG Simulation using MATLAB in which we have seen how to simulate an ECG signal and then diagnose heart disease. We have also extracted ECG features in that project. So, if you guys haven't read that tutorial then I would suggest you to not read this one. First read ECG Simulation using MATLAB and then you should read this tutorial. Today's project is quite an extension of our previous project ECG Simulation using MATLAB. Our team has designed this project after quite a lot of effort that's why its not free to ...
