TEP DOWNLOAD CENTER

Project Files of Serial Monitor Proteus Library | Advance Serial Terminal in Proteus

Libraries Code Projects Simulation
tep://download-terminal tep-serial-monitor-advance-v1-0-1-9f575b6fbeee43a0b75be11cacb9d7b2.zip ZIP archiveV1.0.1Verified33 downloadsFree
Serial Monitor Proteus Library: the TEP Serial Monitor Advance, an advance serial terminal in Proteus, open next to an Arduino UNO
Proteus library · File 1 of 1

TEP Serial Monitor Advance Library for Proteus V1.0.1

TEP Serial Monitor Advance Library for Proteus V1.0.1 comes as a ZIP archive of 9 files (968.4 KB, 2.1 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware.

  • LIBProteus library
  • IDXProteus library index
  • DLLProteus model
  • DSNProteus simulation
  • INOArduino sketch
  • HEXHEX firmware

Description

Looking for the files of Serial Monitor Proteus Library | Advance Serial Terminal in Proteus? TEP Serial Monitor Advance Library for Proteus V1.0.1 is the ZIP package (968.4 KB) you need. It holds the Proteus library files (LIB and IDX), the simulation model (DLL), a ready Proteus simulation, an Arduino sketch and the compiled HEX firmware. Below are the file structure, the README and the installation steps, so you can go from download to a working Proteus simulation in a few minutes.

What this library is

TEP-Serial-Monitor-Advance-Library-for-Proteus-v1.0.1.zip with the TEP Serial Monitor Advance (TEPSERIALMON.LIB and TEPSERIALMON.DLL), the TEP Arduino UNO library for Proteus, the Arduino UNO demo simulation with its HEX file, the demo sketch and a README.

This is version 1.0.1; older or newer releases, when they exist, are listed in the Development tab.

What is inside the ZIP file

  • ArduinoV3TEP.LIB – Proteus library, 95.6 KB
  • TEPSERIALMON.LIB – Proteus library, 11.1 KB
  • ArduinoV3TEP.IDX – Library index, 830 B
  • TEPSERIALMON.DLL – Simulation model, 978 KB
  • TEP-Serial-Monitor-Demo-ArduinoUnoV3.pdsprj – Proteus simulation, 17.7 KB
  • SerialMonitor_Demo.ino – Arduino sketch, 3.8 KB
  • and 3 more, all listed in the File Structure tab

The archive unpacks to 2.1 MB and carries its own README (README.txt), shown in the README tab above.

How to download

Use the download panel at the top of this page: after the counter (30 seconds for guests, 10 for members) the black button unlocks and the ZIP file comes straight from our content network. If the browser opens it instead of saving, use Save as; extract the whole archive before using anything inside it.

How to install

  • Step 1: Extract the ZIP file with Windows (Extract All), 7-Zip or WinRAR, keeping its folders.
  • Step 2: Close Proteus and copy ArduinoV3TEP.LIB and TEPSERIALMON.LIB and ArduinoV3TEP.IDX into its LIBRARY folder (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY).
  • Step 3: Copy TEPSERIALMON.DLL into the MODELS folder next to it, so the part simulates.
  • Step 4: Start Proteus, press P and search for "ArduinoV3TEP"; place and wire it as in the tutorial.
  • Step 5: Open SerialMonitor_Demo.ino in the Arduino IDE, pick board and port and Verify (Export Compiled Binary gives the HEX).
  • Step 6: In Proteus set the controller's Program File to SerialMonitor_Demo.hex; on hardware, flash the same file.
  • Step 7: Open TEP-Serial-Monitor-Demo-ArduinoUnoV3.pdsprj in Proteus and press Play.

Read the detailed guide

This page is for the files. The full tutorial, Serial Monitor Proteus Library | Advance Serial Terminal in Proteus, explains the circuit and the code step by step and shows the working results and the simulation; read it before you build. Questions about the download or the installation go in the comments below; more Proteus downloads are listed further down this page.

Read Serial Monitor Proteus Library | Advance Serial Terminal in Proteus

File Structure

tep-serial-monitor-advance-v1-0-1-9f575b6fbeee43a0b75be11cacb9d7b2.zip9 files · 5 folders · 2.1 MB unpacked
TEP-Serial-Monitor-Advance-v1.0.1/9 files · 2.1 MB
Arduino Code/1 file · 3.8 KB
SerialMonitor_Demo/1 file · 3.8 KB
INO SerialMonitor_Demo.inoArduino sketch 3.8 KB
Proteus Library Files/3 files · 107.5 KB
IDX ArduinoV3TEP.IDXLibrary index 830 B
LIB ArduinoV3TEP.LIBProteus library 95.6 KB
LIB TEPSERIALMON.LIBProteus library 11.1 KB
Proteus Model Files/1 file · 978 KB
DLL TEPSERIALMON.DLLSimulation model 978 KB
Proteus Simulation/3 files · 1012.8 KB
HEX SerialMonitor_Demo.hexCompiled HEX file 17.1 KB
DSN TEP-Serial-Monitor-Demo-ArduinoUnoV3.pdsprjProteus simulation 17.7 KB
DLL TEPSERIALMON.DLLSimulation model 978 KB
TXT README.txtText file 13.8 KB

README

README.txt 228 lines
TEP SERIAL MONITOR ADVANCE LIBRARY FOR PROTEUS - V1.0.1
Serial Monitor + Serial Plotter + hardware COM Bridge for Proteus 8
Designed by The Engineering Projects
www.TheEngineeringProjects.com

IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
  https://www.theengineeringprojects.com/2026/10/serial-monitor-advance-proteus-library.html
Report a bug or suggest a feature (our forum):
  https://www.theengineeringprojects.com/forum/category/tep-serial-monitor-library-for-proteus

FILE STRUCTURE
TEP-Serial-Monitor-Advance-v1.0.1/
|-- Proteus Library Files/
|   |-- ArduinoV3TEP.IDX                                          0.8 KB   library index -> copy to Proteus LIBRARY folder (Arduino UNO used by the demo)
|   |-- ArduinoV3TEP.LIB                                         95.6 KB   library -> copy to Proteus LIBRARY folder (Arduino UNO used by the demo)
|   |-- TEPSERIALMON.LIB                                         11.1 KB   library -> copy to Proteus LIBRARY folder
|-- Proteus Model Files/
|   |-- TEPSERIALMON.DLL                                        978.0 KB   simulation model -> copy to Proteus MODELS folder
|-- Proteus Simulation/
|   |-- SerialMonitor_Demo.hex                                   17.1 KB   demo program for the Arduino UNO
|   |-- TEP-Serial-Monitor-Demo-ArduinoUnoV3.pdsprj              17.7 KB   demo project - open this in Proteus
|   |-- TEPSERIALMON.DLL                                        978.0 KB   copy of the model so the demo runs as is
|-- Arduino Code/
|   |-- SerialMonitor_Demo/SerialMonitor_Demo.ino                 3.8 KB   demo Arduino sketch (source of the .hex)
|-- README.txt                                                    ~13.2 KB   this file
Total: 2.06 MB (unzipped). The C++ source code of the model is not included.

WHAT IS IT?
The TEP Serial Monitor Advance is a better replacement for the Virtual
Terminal of Proteus. Connect it to the TX / RX pins of your Arduino (or any
microcontroller UART) and press Run: a big, modern window opens that looks and
works like the Serial Monitor and Serial Plotter of the Arduino IDE.
  * Long lines are never cut off, it never stops scrolling (50,000 lines kept).
  * Line numbers, timestamps (simulation time or PC clock), RX / TX tags in
    colour, ASCII, HEX or both side by side.
  * Type a message and press Enter to send it to your Arduino; 4 quick-send
    buttons for the commands you use most.
  * A Serial Plotter tab draws the numbers your sketch prints, just like the
    Arduino IDE's plotter (up to 8 traces).
  * A Bridge tab connects the simulated circuit to a REAL COM port of your PC.
  * 9 colour themes (TEP Dark is the default), zoom, Settings and Help pages.
Device name in Proteus: SERIALMONTEP (category Debugging Tools > Serial).

TEST STATUS
Tested in Proteus 8.5 (Windows 11) with the supplied demo project: the window
opens at Run, the demo banner and "You typed: ..." echo, LED ON / LED OFF on
D13, the sin / cos / ramp traces in the Plotter tab and the Simple
interface. The model was also tested on a PC with 1,000+
automatic checks (the UART at every baud rate and format, the window, the
bridge through a simulated port). The Bridge tab was NOT yet tried with a
real COM port (the test PC has none). Proteus 7 is not supported.

INSTALLATION (about 2 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy the files in "Proteus Library Files" (TEPSERIALMON.LIB and the TEP
   Arduino UNO V3 library ArduinoV3TEP.LIB / .IDX used by the demo) to the
   LIBRARY folder of Proteus, for example:
     C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
   (on some PCs: C:\ProgramData\Labcenter Electronics\Proteus 8 Professional\
   LIBRARY - use the folder that already holds Proteus's own .LIB files).
3. Copy TEPSERIALMON.DLL from "Proteus Model Files" to the MODELS folder:
     C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\MODELS
   (or ...\ProgramData\...\MODELS, as above).
4. Start Proteus. In Pick Devices (P) search "SERIALMON" or "Serial Monitor".
Tested with Proteus 8.5. No extra Windows software is needed.

RUN THE DEMO
1. Open "Proteus Simulation\TEP-Serial-Monitor-Demo-ArduinoUnoV3.pdsprj".
   Keep SerialMonitor_Demo.hex (the Arduino program) beside the project.
2. Press Run. The TEP Serial Monitor window opens by itself and shows:
     === TEP Serial Monitor demo (Arduino UNO, 9600 baud) ===
     Commands: HELP, LED ON, LED OFF, PLOT ON, PLOT OFF, STATUS
     Ready - type a command and press Enter.
   followed by a stream of lines like  sin:0.153,cos:0.868,ramp:-0.40
3. Click the Plotter tab: three moving traces (sin, cos, ramp).
4. Click the quick-send buttons HELP / LED ON / LED OFF / PLOT OFF, or type a
   command in the send box and press Enter. The Arduino answers
   "You typed: LED ON" and "LED on D13 is now ON" (pin 13's logic square on
   the UNO turns red; add an LED + 220 ohm resistor from D13 to GND to see it).
5. Closed the window? Click the OPEN MONITOR button on the part, or use the
   Debug menu of Proteus.
The sketch is in "Arduino Code\SerialMonitor_Demo" (plain Arduino code,
hardware Serial at 9600 baud, no libraries needed).

PINS AND WIRING
  RXD   input  - the monitor RECEIVES here: connect it to the Arduino's TX (D1)
  TXD   output - the monitor SENDS here:    connect it to the Arduino's RX (D0)
  RXD2  input  - optional second receive channel (shown as RX2 in amber), e.g.
                 to watch another UART line at the same time; leave it open
                 if not used
  GND   ground (optional in Proteus)
Demo wiring: monitor RXD <- UNO D1 (TX), monitor TXD -> UNO D0 (RX), GND to
ground, RXD2 open. In the sketch: Serial.begin(9600);
Remember: TX of one side always goes to RX of the other side.

MAIN FEATURES
Monitor tab
  * baud rate dropdown (300 ... 2,000,000 or AUTO detect), data bits, parity,
    stop bits (e.g. 8N1), inverted (RS232) levels
  * ASCII / HEX / BOTH view, line numbers, timestamps (OFF, simulation time,
    PC clock), RX / TX / RX2 tags, framing / parity errors marked in red
  * search, pause, auto-scroll, clear, save the log as a text file
  * send box with line ending (None, Newline, CR, Both), history (Up / Down
    arrows), 4 quick-send buttons (properties QUICK1 ... QUICK4)
Plotter tab
  * the Arduino IDE plotter format: "1.5 2.7", "1.5,2.7" or
    "temp:21.5,hum:40"; up to 8 traces with names, legend, hover values,
    auto or fixed scale, samples shown (50 ... 5000)
Bridge tab (real hardware)
  * connects the simulated UART to a real COM port of your PC (USB-serial
    adapter, a real Arduino, a Bluetooth / GPS module ...): port picker,
    baud (same as the monitor or another rate), direction (both / to the
    port / from the port), DTR / RTS, an optional DTR reset pulse for a real
    Arduino, auto-reconnect, counters and a traffic log
Look and comfort
  * 9 themes: TEP Dark (default), TEP Website, TEP Classic, Light, Matrix,
    Amber CRT, Ocean, Dracula, High Contrast; zoom 70 ... 220 %
  * Settings page (cog icon): theme, font size, line numbers, timestamps,
    lines kept, line ending, open window at Run, plotter options ...
    remembered for the next time
  * Simple interface: one slim row + the log + the send box (Settings, or
    property UI = SIMPLE). Back to the full window: the corner button,
    right-click > Full interface, Esc or Ctrl+Shift+U
  * Help page (? icon): article, bug report, feature request, forum, donate,
    website, Copy diagnostics, Check for updates
  * the part on the schematic is live too: a mini screen with the last lines,
    RX / TX / RX2 / HW LEDs, counters, a small plot and the OPEN MONITOR button
The TEP Serial Monitor Expert (more tools) has its own device and file names,
so both editions can be installed side by side.

PROPERTIES (double-click the part > Edit Properties)
  BAUD         Baud rate (300 to 2000000, or AUTO)             default 9600
  DATABITS     Data bits (5, 6, 7 or 8)                        default 8
  PARITY       Parity (NONE, EVEN, ODD)                        default NONE
  STOPBITS     Stop bits (1 or 2)                              default 1
  UARTINVERT   Invert the UART levels, RS232 polarity (NO, YES) default NO
  BAUD2        RXD2 baud rate (SAME, AUTO or a number)         default SAME
  AUTOOPEN     Open the window at Run (YES, NO)                default YES
  PLOTTER      Start tab (MONITOR, PLOTTER)                    default MONITOR
  THEME        Window theme (TEPDARK, WEBSITE, CLASSIC, LIGHT, MATRIX,
               AMBER, OCEAN, DRACULA, CONTRAST)                default TEPDARK
  DISPLAY      Display (ASCII, HEX, BOTH)                      default ASCII
  TIMESTAMP    Timestamps (OFF, SIM, PC)                       default OFF
  LINEEND      Line ending (NONE, NL, CR, BOTH)                default NL
  ECHO         Show sent text (YES, NO)                        default YES
  LINENUMBERS  Line numbers (YES, NO)                          default YES
  FONTSIZE     Font size in points (8 to 28)                   default 11
  MAXLINES     Lines kept (1000 to 200000)                     default 50000
  PLOTWINDOW   Plotter samples shown (50 to 5000)              default 500
  PLOTMIN      Plotter scale min (AUTO or a number)            default AUTO
  PLOTMAX      Plotter scale max (AUTO or a number)            default AUTO
  QUICK1..4    Quick send buttons 1 to 4 (text to send)        empty
               (the demo uses HELP, LED ON, LED OFF, PLOT OFF)
  WINDOW       Window type (POPUP or OWN)                      default POPUP
  BRIDGEPORT   Hardware bridge COM port (NONE, COM3, ...)      default NONE
  BRIDGEBAUD   Bridge baud rate (SAME or a number)             default SAME
  BRIDGEMODE   Bridge direction (BOTH, TOHW, FROMHW)           default BOTH
  BRIDGEDTR    Bridge DTR line on (YES, NO)                    default YES
  BRIDGERTS    Bridge RTS line on (YES, NO)                    default YES
  BRIDGERESET  Bridge DTR reset pulse on connect (NO, YES)     default NO
  BRIDGEAUTO   Bridge reconnects automatically (YES, NO)       default YES
  UI           Interface (FULL, SIMPLE)                        default FULL
Settings made in the window are saved for your Windows user and come back next
time. A property you CHANGED from its default in Edit Properties always wins
over the saved setting. WINDOW = OWN opens the monitor in its own window
instead of a Proteus popup (only needed if the popup misbehaves on your PC).

LINKS.INI (OPTIONAL)
The Help page buttons open web pages. To point them somewhere else without a
new DLL, put a text file named links.ini next to TEPSERIALMON.DLL with lines
KEY=URL, for example:
  ARTICLE=https://www.theengineeringprojects.com/2026/10/serial-monitor-advance-proteus-library.html
Keys: WEBSITE, FORUM, FORUM_SERIAL_MONITOR_ADVANCE, BUG_REPORT,
FEATURE_REQUEST, ARTICLE, USER_GUIDE, DOWNLOAD, DONATE, UPDATE_CHECK_ADVANCE.
Only http:// and https:// links are used; lines starting with # are comments.
You do not need this file - the built-in links are correct.

TROUBLESHOOTING
* The window does not open: wait 1-2 s after Run, click OPEN MONITOR on the
  part or use the Debug menu. Check AUTOOPEN = YES.
* Strange characters or red error marks: the baud rate / format of the
  monitor and the sketch differ. Set the same baud (or AUTO).
* Nothing arrives: RXD must go to the Arduino's TX pin (D1), TXD to RX (D0).
* The part is not simulated ("no model"): TEPSERIALMON.DLL is missing from
  MODELS (and from the project folder).
* Proteus shows an old library title: delete TEPSERIALMON.IDX in the LIBRARY
  folder (Proteus rebuilds it).
* Bridge says PORT BUSY: close the other program that uses the COM port
  (Arduino IDE serial monitor, PuTTY ...).

BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum (include a screenshot and, if you can, the
"Copy diagnostics" text from the Help page):
  https://www.theengineeringprojects.com/forum/category/tep-serial-monitor-library-for-proteus

SUPPORT US
This library is free. If it saves you time, please support our work:
  https://www.theengineeringprojects.com/donate

WEBSITE
  https://www.theengineeringprojects.com/

LICENCE AND THIRD-PARTY NOTES
* The TEP Serial Monitor Advance model (TEPSERIALMON.DLL), its symbol and
  artwork are made by The Engineering Projects. The model uses only standard
  Windows system libraries and contains no third-party code. The C runtime is
  built in, so no Visual C++ redistributable is needed.
* With the built-in links the model does not contact the internet by itself:
  the Help page opens web pages in your browser only when you click a card or
  "Check for updates". Window settings are stored in the Windows registry
  under HKEY_CURRENT_USER\Software\TheEngineeringProjects\TEP Serial Monitor.
* TEP Arduino UNO V3 library (ArduinoV3TEP.LIB / .IDX): The Engineering
  Projects, https://www.theengineeringprojects.com/2023/10/arduino-library-for-proteus-v30.html
* Arduino AVR core 1.8.6: SerialMonitor_Demo.hex is built from the demo sketch
  and the Arduino AVR core, which includes LGPL-licensed code. Its source code
  is available at https://github.com/arduino/ArduinoCore-avr/tree/1.8.6
* Proteus is a product of Labcenter Electronics and is not included, nor is
  Labcenter's VSM SDK. Arduino is a trademark of Arduino SA; its use here
  identifies compatible software, not endorsement.

VERSION
TEP Serial Monitor Advance v1.0.1 (build 2026-10-05), package v1.0.1, October 2026.
Device SERIALMONTEP, files TEPSERIALMON.LIB / TEPSERIALMON.DLL.
Changes in v1.0.1 (5 Oct 2026): when two channels arrive at the same time (for
example a sketch printing on RXD while a GPS streams NMEA into RXD2), each
channel now keeps its own line, so both lines stay whole instead of breaking
into one-character rows.
Advertisement

Development1 release

  1. V1.0.1TEP Serial Monitor Advance Library for Proteus V1.0.1this page

    V1.0.1 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.

Installation8 steps

From the download to a working project, in order. The steps follow what the package contains.

You will need

  • Proteus Design SuiteProteus 7 or newer (Labcenter), on Windows
  • Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
  • Any archive toolWindows, macOS and Linux extract ZIP files on their own

Steps

  1. 1

    Extract the archive

    Right-click tep-serial-monitor-advance-v1-0-1-9f575b6fbeee43a0b75be11cacb9d7b2.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (TEP-Serial-Monitor-Advance-v1.0.1) as it is.

  2. 2

    Copy the library files into Proteus

    Move ArduinoV3TEP.LIB and TEPSERIALMON.LIB and ArduinoV3TEP.IDX into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.

  3. 3

    Add the simulation model

    Copy TEPSERIALMON.DLL into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.

  4. 4

    Restart Proteus and place the component

    Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.

  5. 5

    Open the sketch in the Arduino IDE

    Open SerialMonitor_Demo.ino, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.

  6. 6

    Load the HEX file

    In Proteus double-click the microcontroller, set Program File to SerialMonitor_Demo.hex and run the simulation. For real hardware, flash the same file with your programmer.

  7. 7

    Open the example simulation

    Open TEP-Serial-Monitor-Demo-ArduinoUnoV3.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.

  8. 8

    Follow the tutorial

    Serial Monitor Proteus Library | Advance Serial Terminal in Proteus explains every connection and setting in order; keep it open beside the files while you build.

How to add a library in Proteus 8

FAQs9 questionsContact TEP

How do I download TEP Serial Monitor Advance Library for Proteus V1.0.1?

Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.

What is inside the archive?

TEP Serial Monitor Advance Library for Proteus V1.0.1 comes as a ZIP archive of 9 files (968.4 KB, 2.1 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware. Open the File Structure tab for the full list of 9 files.

What should I do if the download does not start?

Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.

Is this file free?

Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.

How do I check that the file arrived complete?

Compare its SHA-256 with the one on this page, facdd85c01fd948905bdcaa8eee9e4a5cc6326ffd5bb43c00f87a985204bfe71. In PowerShell run Get-FileHash "tep-serial-monitor-advance-v1-0-1-9f575b6fbeee43a0b75be11cacb9d7b2.zip"; on macOS or Linux run shasum -a 256 "tep-serial-monitor-advance-v1-0-1-9f575b6fbeee43a0b75be11cacb9d7b2.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.

Do I need WinRAR to open the ZIP file?

No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.

Where do I put the LIB and IDX files?

Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.

Which Proteus version does the library need?

The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.

How do I get the HEX file into the simulation?

Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.

preparing · tep-serial-monitor-advance-v1-0-1-9f575b6fbeee43a0b75be11cacb9d7b2.zip
Rating
Your download will be ready shortly
Preparing your download…

Members skip the wait. Log in or join TEP.

  • 33Total downloads
  • 4%Popularity
  • ProteusCategory
  • 0Comments
  • ssyedzainnasirUploaded by
  • 1 Oct 2026Uploaded at
Last 14 days28 downloads
SHA-256 facdd85c01fd948905bdcaa8eee9e4a5cc6326ffd5bb43c00f87a985204bfe71
DocumentationSerial Monitor Proteus Library | Advance Serial Terminal in Proteus
Need help with this file? Bug report Ask a question Download problemsGet updates
Advertisement

Comments

0

Join the conversation

Start the conversationAsk a question or share how you used this download.