Project Files of SparkFun Pro nRF52840 Mini Library for Proteus: BLE Simulation
59e325a520a7472caaab0d1dd00888ce.zip

SparkFun Pro nRF52840 Mini Library for Proteus V1.0
SparkFun Pro nRF52840 Mini Library for Proteus V1.0 comes as a ZIP archive of 332 files (4.2 MB, 9.8 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code.
- LIBProteus library
- DLLProteus model
- DSNProteus simulation
- INOArduino sketch
- LIBArduino library
- HEXHEX firmware
- SRCSource code
Description
SparkFun-Pro-nRF52840-Mini-Library-for-Proteus-v1.0.zip with SparkFun's Pro nRF52840 Mini in Proteus (your sketch with SparkFun's pin numbers, analogRead on A0 .. A7, the blue LED, BOOTLOAD, Qwiic SDA / SCL, Bluetooth LE to a phone and a serial monitor; TEPSFMINI52.LIB, TEPNET.DLL and the TEP Boards for Proteus add-on 1.93.0), the potentiometer, LED and resistor libraries, the dimmer demo and a README.
File Structure
4.2 KB1.1 KB7.7 KB11 KB8.5 KB1.5 KB1.7 KB1.9 KB5.7 KB4.9 KB1.1 KB5.8 KB9.6 KB7.2 KB2.5 KB2.1 KB1.9 KB2.1 KB4.4 KB1.1 KB3 KB3 KB1.8 KB2.5 KB3.5 KB149 B2.7 KB2 KB6.4 KB3.2 KB1.3 KB963 B8.6 KB5.9 KB6 KB12 KB1.6 KB1.3 KB14.7 KB4.3 KB6.1 KB20.1 KB8.2 KB2 KB4.5 KB311 B12.8 KB6.7 KB6.1 KB2.2 KB3.4 KB5.9 KB1.5 KB1.6 KB16.6 KB9.7 KB6.9 KB2.1 KB533 B5.7 KB7.4 KB514 B1.7 KB896 B481 B1.4 KB1012 B482 B936 B559 B467 B3.6 KB3.8 KB504 B956 B575 B455 B8.3 KB10.9 KB522 B79 B5.5 KB3.1 KB79 B442 B918 B1.4 KB1.8 KB1 KB1.3 KB1.4 KB1.8 KB1.4 KB5.7 KB502 B463 B5 KB6.5 KB3.4 KB3.4 KB500 B1.6 KB368 B406 B466 B404 B444 B460 B477 B739 B448 B1.3 KB350 B5.7 KB4 KB562 B1.5 KB2 KB550 B7.2 KB4.1 KB371 B4.5 KB3.5 KB492 B390 B478 B6.6 KB2.4 KB479 B5.1 KB1.9 KB1.3 KB1.3 KB750 B1.3 KB490 B2.2 KB1.9 KB498 B1.2 KB1.2 KB487 B5.1 KB4.6 KB371 B3.6 KB2.5 KB534 B1.5 KB1.2 KB478 B6.2 KB3 KB1.5 KB1.7 KB469 B1 KB1.7 KB433 B294 B358 B1.3 KB2.5 KB13.2 KB3.8 KB659 B510 B4.4 KB1.9 KB5.8 KB11 KB835 B518 B308 B1.3 KB3.3 KB568 B6.4 KB2.3 KB29 B436 B9.2 KB4.9 KB439 B4.2 KB1.5 KB9.3 KB7.1 KB4.7 KB2.4 KB388 B5.1 KB893 B667 B1.3 KB5.5 KB2.3 KB1.8 KB468 B882 B530 B791 B487 B894 B2 KB730 B646 B2.6 KB977 B702 B20.6 KB1.8 KB11.8 KB3.2 KB596 B406 B6.3 KB5.7 KB9.3 KB7.7 KB7.7 KB6.1 KB5.8 KB5.9 KB6.4 KB6.4 KB5.3 KB5.6 KB5.7 KB7.9 KB7.7 KB6.5 KB6.3 KB6.2 KB6.4 KB5.9 KB10.3 KB8.5 KB6.2 KB6.6 KB7.6 KB6.7 KB6.1 KB6.7 KB8.3 KB6.2 KB7.2 KB6.2 KB5.9 KB5.6 KB5.7 KB6.7 KB5.9 KB6.2 KB6 KB6 KB6.1 KB6.3 KB6 KB6.1 KB6.2 KB6 KB5.8 KB6.4 KB6.4 KB6.4 KB3.8 KB6.4 KB7.3 KB6.4 KB4 KB6.9 KB7.7 KB6 KB6.8 KB6.9 KB7 KB7 KB6.3 KB6.4 KB6.5 KB6.5 KB6.6 KB6.5 KB5.9 KB6.1 KB5.6 KB6.6 KB5.9 KB5.9 KB7.5 KB3.9 KB3.8 KB4.5 KB4.4 KB5.4 KB7.7 KB7.1 KB5.8 KB5.9 KB5.9 KB6.9 KB5.7 KB5.9 KB5.8 KB5.5 KB5.5 KB7.1 KB5.2 KB46 KB25.9 KB1.3 KB8.5 KB38.5 KB39.5 KB21.8 KB13.1 KB208.6 KB306.9 KB31.8 KB289.5 KB3.0 MB310 KB311 KB30.6 KB27.2 KB289.5 KB3.0 MB310 KB311 KB12.9 KBGallery12 images from the tutorialOpen the tutorial
The circuit, the board and the results as they appear in SparkFun Pro nRF52840 Mini Library for Proteus: BLE Simulation. Open an image for its full size.












README
SPARKFUN PRO NRF52840 MINI LIBRARY FOR PROTEUS - V1.0 (YOUR ARDUINO SKETCH, BLUETOOTH LE, THE LED AND THE BUTTON)
Designed by The Engineering Projects
www.TheEngineeringProjects.com
IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
https://www.theengineeringprojects.com/2026/11/sparkfun-pro-nrf52840-mini-library-for-proteus.html
Report a bug or suggest a feature (our forum):
https://www.theengineeringprojects.com/forum
The demo's other parts are our libraries (included) - their articles:
https://www.theengineeringprojects.com/2026/11/potentiometer-library-for-proteus.html
https://www.theengineeringprojects.com/2026/11/5mm-led-library-for-proteus.html
https://www.theengineeringprojects.com/2026/11/resistor-library-for-proteus.html
https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
Support us (the libraries are free):
https://www.theengineeringprojects.com/donate
FILE STRUCTURE
SparkFun-Pro-nRF52840-Mini-TEP-v1.0/
|-- Proteus Library Files/
| |-- TEPLAPTOP.LIB 39.5 KB the laptop (demo), to LIBRARY
| |-- TEPLED5MM.LIB 21.8 KB the 5 mm LED (demo), to LIBRARY
| |-- TEPMOBILE.LIB 13.1 KB the phone (demo), to LIBRARY
| |-- TEPPOT.LIB 208.6 KB the potentiometer (demo), to LIBRARY
| |-- TEPRESISTOR.LIB 306.9 KB the resistor (demo), to LIBRARY
| |-- TEPSFMINI52.LIB 31.8 KB the SparkFun Pro nRF52840 Mini, to LIBRARY
|-- Proteus Model Files/
| |-- TEPLED5MM.DLL 289.5 KB the 5 mm LED, to MODELS
| |-- TEPNET.DLL 2.98 MB the board + monitors + network, to MODELS
| |-- TEPPOT.DLL 310.0 KB the potentiometer, to MODELS
| |-- TEPRESISTOR.DLL 311.0 KB the resistor, to MODELS
|-- Arduino Code/
| |-- SFMini52_BLE_Dimmer/SFMini52_BLE_Dimmer.ino 4.2 KB the demo sketch
| |-- TEP Boards for Proteus/hardware/ 1.34 MB the Arduino IDE add-on 1.93.0 (314 files)
|-- Proteus Simulation/
| |-- SFMini52_BLE_Dimmer.hex 30.6 KB the demo sketch (U1)
| |-- SparkFun-Pro-nRF52840-Mini-BLE-Dimmer.pdsprj 27.2 KB the demo: a Bluetooth LE dimmer
| |-- TEPLED5MM.DLL 289.5 KB copy of the model
| |-- TEPNET.DLL 2.98 MB copy of the model
| |-- TEPPOT.DLL 310.0 KB copy of the model
| |-- TEPRESISTOR.DLL 311.0 KB copy of the model
|-- README.txt ~12.2 KB this file
Total: 9.75 MB (unzipped). The source code of the models is not included.
WHAT IS IT?
Proteus 8 has no nRF52840 processor model, so this is NOT a real nRF52840 chip. Our team has put a lot of effort into
building this board ourselves: it is SparkFun's Pro nRF52840 Mini (DEV-15025) - the red board of 46.99 x 22.86 mm
(drawn at true scale from SparkFun's own board file) with the Raytac MDBT50Q module (the nRF52840: an Arm Cortex-M4F,
Bluetooth LE, native USB), 2 MB of QSPI flash, the micro-USB, a LiPo charger with its JST socket, the ON/OFF switch,
RESET, the BOOTLOAD button, the red power LED, the blue user LED, the yellow charge LED, the Qwiic socket, the Cortex
debug header and the two rows of pins with their ground pads - and it runs YOUR Arduino sketch in Proteus:
* You write a normal sketch with SparkFun's pin numbers - Arduino pin n is P0.n (analogRead 0-1023 on A0 .. A7 =
2, 3, 4, 5, 28, 29, 30, 31; analogWrite, attachInterrupt, pulseIn, tone, Wire, Serial, Serial1) and compile it in
the Arduino IDE with our board package "TEP Boards for Proteus" 1.93.0 (in Arduino Code - see INSTALLATION).
* The blue LED (pin 7, LED_BUILTIN, the real P0.07) lights when HIGH. The BOOTLOAD button (pin 13, PIN_BUTTON1, the
real P0.13) reads LOW while you hold it: click it on the board in the running simulation.
* Bluetooth LE works through ArduinoBLE: the board advertises as a peripheral with your services and
characteristics, and our Mobile WiFi Monitor's Bluetooth app is the central (it lists the board, connects, reads,
writes and gets the notifications).
TEP additions: the micro-USB opens the serial monitor (the same window as our TEP Serial Monitor Advance); the Qwiic
socket's SDA (pin 8) and SCL (pin 11) are pins of the part, so you can wire I2C modules to them.
Limits (say them before you start): in the simulation the SPI library is not available on this board - its SPI pins
(2, 3, 30, 31) are the analog inputs here. analogRead takes the pin numbers (A0 is pin 2). The pins that are not broken
out are inside the part. The charger, the ON/OFF switch and the yellow charge LED are drawn, not modelled. One phone is
the central; the board cannot be a central itself. Your sketch gets 8 KB of RAM in the simulation (the real one:
256 KB), about 256 KB of flash, and int is 16 bits in the simulation (use long for big numbers).
ONE DEVICE (search "SPARKFUN" in Pick Devices):
SPARKFUN NRF52840 MINI "Pro nRF52840 Mini" V1.0 (Microprocessor ICs > Bluetooth Boards), prefix U, model TEPNET.DLL.
Its TEP window has no Windows title bar: the serial monitor (the micro-USB, 115200 baud: Monitor, Plotter and Board
tabs).
The same TEPNET.DLL also runs our other sketch boards and the phone; it replaces any older TEPNET.DLL (keep only this
newest one in MODELS).
TEST STATUS
V1.0: verified in Proteus 8.5 on 18 Nov 2026 with the demo project as shipped. What the Proteus run showed:
* SparkFun-Pro-nRF52840-Mini-BLE-Dimmer: "Advertising as "Pro Mini Dimmer"", the knob at 49 %; the phone's Bluetooth
app, SCAN, connect: "Phone connected" (the blue LED lit), the level and the lamp's state.
* RV1's +10 % chip three times: ">> LEVEL 51 %" .. ">> LEVEL 77 %" in steps of 2 % (the filter), the lamp brighter.
* BOOTLOAD: ">> BUTTON: the lamp OFF" (the level kept: 79 %); again: "the lamp ON"; the knob all the way up: 99 %.
* about 60 s of simulation, no errors, with the phone, the potentiometer's window and the monitor open.
INSTALLATION (about 3 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" to the LIBRARY folder of Proteus, for example:
C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
(on some PCs: C:\ProgramData\Labcenter Electronics\Proteus 8 Professional\LIBRARY). TEPSFMINI52.LIB is the board;
TEPPOT.LIB, TEPLED5MM.LIB and TEPRESISTOR.LIB are the demo's potentiometer, 5 mm LED and resistor, TEPMOBILE.LIB and
TEPLAPTOP.LIB the phone and the laptop.
3. Copy the DLLs from "Proteus Model Files" (TEPNET.DLL, TEPPOT.DLL, TEPLED5MM.DLL, TEPRESISTOR.DLL) to the MODELS
folder (...\Proteus 8 Professional\MODELS) - replace an older TEPNET.DLL (this one is the first that knows this
board).
4. Delete TEPSFMINI52.IDX from the LIBRARY folder if it is there.
5. The Arduino IDE (only to compile your own sketches - the demo has its HEX file): copy the folder
"Arduino Code\TEP Boards for Proteus\hardware" into your sketchbook folder (normally Documents\Arduino), so that
Documents\Arduino\hardware\tep\avr\boards.txt exists (replace an older copy); restart the IDE. The Arduino AVR Boards
platform must be installed (it comes with IDE 1.8.x; in IDE 2.x install "Arduino AVR Boards" from the Boards
Manager once).
Tools > Board > TEP Boards for Proteus > SparkFun Pro nRF52840 Mini (TEP Proteus). ArduinoBLE is in the board
package.
6. Start Proteus. In Pick Devices (P) search "SPARKFUN".
RUN THE DEMO
Keep the .hex file and the DLLs beside the project in "Proteus Simulation".
SparkFun-Pro-nRF52840-Mini-BLE-Dimmer.pdsprj - U1 the Pro nRF52840 Mini (SFMini52_BLE_Dimmer.hex) is a Bluetooth desk
lamp dimmer: RV1 = our 9 mm potentiometer, the knob (pin 1 to ground, pin 3 to +3.3V, the wiper on A2 = pin 4 = KNOB),
D1 = our 5 mm white LED, the lamp, through R1 (220 ohm) on pin 19 = LAMP; MOB1 = the phone (Mobile WiFi Monitor),
whose Bluetooth app connects to it.
Press Run. The monitor prints "Advertising as "Pro Mini Dimmer"" and the knob's level. On the phone open the Bluetooth
app, press SCAN and connect (the blue LED lights): it shows the level and the lamp's state. In RV1's window turn the
knob (the +10 % chip): ">> LEVEL ..." and the lamp brighter (PWM with a gamma curve). Click BOOTLOAD: "the lamp OFF";
again: ON at the same level.
Closed a window? The micro-USB opens the monitor, a click on the pot its window, a click on the phone's screen the
phone.
THE PINS (the label on the part, what it can do in the simulation; the real board's pad from SparkFun's board file)
2, 3, 4, 5 A0 .. A3: analogRead 0 .. 1023 for 0 .. 3.3 V, or GPIO, PWM (P0.02 .. P0.05)
28 .. 31 A4 .. A7: analogRead, or GPIO, PWM (P0.28 .. P0.31)
17, 15 Serial1 TX / RX, or GPIO (P0.17, P0.15)
19 .. 23, 9, 10 GPIO, PWM, interrupt, pulse timing (P0.19 .. P0.23, P0.09, P0.10 - NFC1 / NFC2 on the real board)
SDA, SCL Wire on the Qwiic socket (pins 8 / 11: P0.08, P0.11)
3V3, VIN, GND 3.3 V (the logic), 5 V, ground; RST the board's reset (the RESET button too)
The blue LED is pin 7 (LED_BUILTIN, LED_BLUE, lit when HIGH); the BOOTLOAD button is pin 13 (PIN_BUTTON1, LOW when
pressed, pinMode INPUT_PULLUP). Serial is the USB: the board's built-in monitor. The row of ground pads beside each
header is drawn (use the GND pin).
PROPERTIES (double-click the part > Edit Properties)
PROGRAM the sketch's HEX (Arduino IDE: Sketch > Export Compiled Binary with the TEP Proteus Pro nRF52840 Mini)
MONITOR YES = the built-in serial monitor on Serial; BAUD its speed (115200, or AUTO)
AUTOOPEN YES = the monitor window opens at Run (the demo: YES)
TROUBLESHOOTING
* The phone's list is empty: call BLE.begin(), set a local name and BLE.advertise(); call BLE.poll() in loop().
* analogRead reads the wrong input: pass the pin number (A0 is pin 2, A2 is pin 4) - not 0 .. 7.
* The level jitters: smooth the readings and tell the phone only about changes of 2 % or more.
* The lamp looks too bright at low levels: use a gamma curve (brightness = level squared).
* An integer goes wrong above 32767: int is 16 bits in the simulation - use long.
BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot and the Serial Monitor text:
https://www.theengineeringprojects.com/forum
LICENCES AND THIRD-PARTY NOTES
* The board model (TEPNET.DLL), the symbols and artwork (TEPSFMINI52.LIB) and the potentiometer, LED and resistor models
are made by The Engineering Projects. The source code of the models is not included.
* TEP Boards for Proteus (Arduino Code): its core, the variants and the EEPROM, SPI and Wire libraries are modified
copies of the Arduino AVR core 1.8.6 - GNU Lesser General Public License 2.1 (LGPL 2.1, the text:
LICENSE-LGPL-2.1.txt); its ArduinoBLE and the others and our core files are MIT (LICENSE-MIT.txt).
* Our ArduinoBLE has the calls of the library of that name; its code is ours.
* Proteus is a product of Labcenter Electronics and is not included. SparkFun and Qwiic are names of SparkFun
Electronics, nRF52840 of Nordic Semiconductor ASA, MDBT50Q of Raytac, Arduino of Arduino. The Bluetooth word mark
belongs to Bluetooth SIG. This library is not made or endorsed by them or by Labcenter.
REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied. Install TEP Boards for Proteus (INSTALLATION step 5), open Arduino Code\SFMini52_BLE_Dimmer,
select SparkFun Pro nRF52840 Mini (TEP Proteus) and use Sketch > Export Compiled Binary. For a real board install
SparkFun's nRF52840 board package (based on Adafruit's) and use Bluefruit or your own Bluetooth code; its pins work at
3.3 V.
MODEL SCOPE AND LIMITS
Modelled: the board's pins; digital I/O, analogRead 0 .. 1023, PWM (analogWrite), pulse timing, tone and
attachInterrupt through the board model; Serial (the board's monitor), Serial1 and Wire; the blue LED, the BOOTLOAD
button and RESET; Bluetooth LE as a peripheral (ArduinoBLE) with the phone as the central.
Not modelled: the nRF52840 itself, the radio's range, the SPI library on this board, the QSPI flash, the charger and
the ON/OFF switch, NFC, the board as a central. The simulation runs below real time.
VERSION
TEP SparkFun Pro nRF52840 Mini library V1.0 (Nov 2026). Device SPARKFUN NRF52840 MINI (TEPSFMINI52.LIB / TEPNET.DLL),
TEP Boards for Proteus 1.93.0 (adds this board: the blue LED, the BOOTLOAD button, SparkFun's pin numbers).
Demo sketch SFMini52_BLE_Dimmer V1.0. Demo parts: POTROTARY9TEP, LED5MMWHITETEP, RESISTOR4BANDTEP and MOBILE WIFI
MONITOR.Development1 release
-
V1.0SparkFun Pro nRF52840 Mini Library for Proteus V1.0this page
V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.
Installation10 steps
From the download to a working project, in order. The steps follow what the package contains.
You will need
- Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
- Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
- The compiler named in the tutorialto build the source files into firmware
- Any archive toolWindows, macOS and Linux extract ZIP files on their own
Steps
- 1
Extract the archive
Right-click 59e325a520a7472caaab0d1dd00888ce.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (SparkFun-Pro-nRF52840-Mini-TEP-v1.0) as it is.
- 2
Copy the library files into Proteus
Move TEPLAPTOP.LIB, TEPLED5MM.LIB and TEPMOBILE.LIB and 3 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.
- 3
Add the simulation model
Copy TEPLED5MM.DLL, TEPNET.DLL and TEPPOT.DLL and 1 more into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.
- 4
Restart Proteus and place the component
Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.
- 5
Install the Arduino library
In the Arduino IDE choose Sketch → Include Library → Add .ZIP Library and pick the library, or copy its folder into Documents\Arduino\libraries. Restart the IDE to see its examples.
- 6
Open the sketch in the Arduino IDE
Open SFMini52_BLE_Dimmer.ino, eeprom_clear.ino and eeprom_crc.ino and 17 more, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.
- 7
Build the source code
Open abi.cpp, Arduino.h and binary.h and 52 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.
- 8
Load the HEX file
In Proteus double-click the microcontroller, set Program File to SFMini52_BLE_Dimmer.hex and run the simulation. For real hardware, flash the same file with your programmer.
- 9
Open the example simulation
Open SparkFun-Pro-nRF52840-Mini-BLE-Dimmer.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.
- 10
Follow the tutorial
SparkFun Pro nRF52840 Mini Library for Proteus: BLE Simulation explains every connection and setting in order; keep it open beside the files while you build.
FAQs9 questionsContact TEP
How do I download SparkFun Pro nRF52840 Mini Library for Proteus V1.0?
Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.
What is inside the archive?
SparkFun Pro nRF52840 Mini Library for Proteus V1.0 comes as a ZIP archive of 332 files (4.2 MB, 9.8 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code. Open the File Structure tab for the full list of 332 files.
What should I do if the download does not start?
Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.
Is this file free?
Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.
How do I check that the file arrived complete?
Compare its SHA-256 with the one on this page, 7f84ecf260614a6dbedf4ae8b36f9b0e5266a290fc5827504fbd49bde96e5107. In PowerShell run Get-FileHash "59e325a520a7472caaab0d1dd00888ce.zip"; on macOS or Linux run shasum -a 256 "59e325a520a7472caaab0d1dd00888ce.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.
Do I need WinRAR to open the ZIP file?
No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.
Where do I put the LIB and IDX files?
Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.
Which Proteus version does the library need?
The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.
How do I get the HEX file into the simulation?
Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.
Members skip the wait. Log in or join TEP.
- 0Total downloads
- 4%Popularity
- ProteusCategory
- 0Comments
- ssyedzainnasirUploaded by
- 22 Nov 2026Uploaded at
7f84ecf260614a6dbedf4ae8b36f9b0e5266a290fc5827504fbd49bde96e5107
















Comments
0