Project Files of nRF54LM20 DK Library for Proteus: nRF54LM20 Bluetooth LE Simulation
4e92157fbff7481a9896b1576f622730.zip

nRF54LM20 DK Library for Proteus V1.0
nRF54LM20 DK Library for Proteus V1.0 comes as a ZIP archive of 325 files (4.2 MB, 9.5 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code.
- LIBProteus library
- DLLProteus model
- DSNProteus simulation
- INOArduino sketch
- LIBArduino library
- HEXHEX firmware
- SRCSource code
Description
nRF54LM20-DK-Library-for-Proteus-v1.0.zip with Nordic's nRF54LM20 DK in Proteus (your sketch with the P0 .. P3 GPIOs, LED0 .. LED3, BUTTON0 .. BUTTON3, Bluetooth LE to a phone and a serial monitor; TEPNRF54LM20DK.LIB, TEPNET.DLL and the TEP Boards for Proteus add-on 1.86.0), the LED, buzzer, resistor and phone libraries, the crossing demo and a README.
File Structure
5.6 KB1.1 KB7.7 KB11 KB8.5 KB1.5 KB1.7 KB1.9 KB5.7 KB4.9 KB1.1 KB5.8 KB9.6 KB7.2 KB2.5 KB2.1 KB1.9 KB2.1 KB4.4 KB1.1 KB3 KB3 KB1.8 KB2.5 KB3.5 KB149 B2.7 KB2 KB6.4 KB3.2 KB1.3 KB963 B8.6 KB5.9 KB6 KB12 KB1.6 KB1.3 KB14.7 KB4.3 KB6.1 KB20.1 KB8.2 KB2 KB4.5 KB311 B12.8 KB6.7 KB6.1 KB2.2 KB3.4 KB5.9 KB1.5 KB1.6 KB16.6 KB9.7 KB6.9 KB2.1 KB533 B5.7 KB7.4 KB514 B1.7 KB896 B481 B1.4 KB1012 B482 B936 B559 B467 B3.6 KB3.8 KB504 B956 B575 B455 B8.3 KB10.9 KB522 B79 B5.5 KB3.1 KB79 B442 B918 B1.4 KB1.8 KB1 KB1.3 KB1.4 KB1.8 KB1.4 KB5.7 KB502 B463 B5 KB6.5 KB3.4 KB3.4 KB500 B1.6 KB368 B406 B466 B404 B444 B460 B477 B739 B448 B1.3 KB350 B5.7 KB4 KB562 B1.5 KB2 KB550 B7.2 KB4.1 KB371 B4.5 KB3.5 KB492 B390 B478 B6.6 KB2.4 KB479 B5.1 KB1.9 KB1.3 KB1.3 KB750 B1.3 KB490 B2.2 KB1.9 KB498 B1.2 KB1.2 KB487 B5.1 KB4.6 KB371 B3.6 KB2.5 KB534 B1.5 KB1.2 KB478 B6.2 KB3 KB1.5 KB1.7 KB469 B1 KB1.7 KB433 B294 B358 B1.3 KB2.5 KB13.2 KB3.8 KB659 B510 B4.4 KB1.9 KB5.8 KB11 KB835 B518 B308 B1.3 KB3.3 KB568 B6.4 KB2.3 KB29 B436 B9.2 KB4.9 KB439 B4.2 KB1.5 KB9.3 KB7.1 KB4.7 KB2.4 KB388 B5.1 KB893 B667 B1.3 KB5.5 KB2.3 KB1.8 KB468 B882 B530 B791 B487 B894 B2 KB730 B646 B2.6 KB977 B702 B20.6 KB1.8 KB11.8 KB3.2 KB596 B406 B6.3 KB5.7 KB9.3 KB7.7 KB7.7 KB6.1 KB5.8 KB5.9 KB6.4 KB6.4 KB5.3 KB5.6 KB5.7 KB7.9 KB7.7 KB6.5 KB6.3 KB6.2 KB6.4 KB5.9 KB10.3 KB8.5 KB6.6 KB7.6 KB6.7 KB6.1 KB6.7 KB8.3 KB6.2 KB7.2 KB6.2 KB5.9 KB5.6 KB5.7 KB6.7 KB5.9 KB6.2 KB6 KB6 KB6.1 KB6.3 KB6 KB6.1 KB6.2 KB6 KB5.8 KB6.4 KB6.4 KB3.8 KB6.4 KB7.3 KB6.4 KB4 KB6.9 KB7.7 KB6 KB6.8 KB7 KB6.3 KB6.4 KB6.5 KB6.5 KB6.6 KB6.5 KB5.9 KB6.1 KB5.6 KB6.6 KB5.9 KB7.5 KB3.8 KB4.4 KB5.4 KB7.7 KB7.1 KB5.8 KB5.9 KB5.9 KB6.9 KB5.7 KB5.9 KB5.8 KB5.5 KB5.5 KB7.1 KB5.2 KB42.3 KB25.9 KB1.3 KB8.5 KB37.6 KB39.5 KB21.8 KB13.1 KB42.2 KB13.4 KB306.9 KB289.5 KB3.0 MB288.5 KB311 KB33.6 KB24.9 KB289.5 KB3.0 MB288.5 KB311 KB13.5 KBGallery12 images from the tutorialOpen the tutorial
The circuit, the board and the results as they appear in nRF54LM20 DK Library for Proteus: nRF54LM20 Bluetooth LE Simulation. Open an image for its full size.












README
NRF54LM20 DK LIBRARY FOR PROTEUS - V1.0 (YOUR ARDUINO SKETCH, BLUETOOTH LE TO A PHONE, 32 GPIOS, LEDS AND BUTTONS)
Designed by The Engineering Projects
www.TheEngineeringProjects.com
IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
https://www.theengineeringprojects.com/2026/11/nrf54lm20-dk-library-for-proteus.html
Report a bug or suggest a feature (our forum):
https://www.theengineeringprojects.com/forum
The demo's other parts are our libraries (included) - their articles:
https://www.theengineeringprojects.com/2026/11/5mm-led-library-for-proteus.html
https://www.theengineeringprojects.com/2026/11/passive-buzzer-library-for-proteus.html
https://www.theengineeringprojects.com/2026/11/resistor-library-for-proteus.html
https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
Support us (the libraries are free):
https://www.theengineeringprojects.com/donate
FILE STRUCTURE
nRF54LM20-DK-TEP-v1.0/
|-- Proteus Library Files/
| |-- TEPLAPTOP.LIB 39.5 KB the laptop (demo), to LIBRARY
| |-- TEPLED5MM.LIB 21.8 KB the 5 mm LEDs (demo), to LIBRARY
| |-- TEPMOBILE.LIB 13.1 KB the phone (demo), to LIBRARY
| |-- TEPNRF54LM20DK.LIB 42.2 KB the nRF54LM20 DK, to LIBRARY
| |-- TEPPASSIVE.LIB 13.4 KB the passive buzzer (demo), to LIBRARY
| |-- TEPRESISTOR.LIB 306.9 KB the resistors (demo), to LIBRARY
|-- Proteus Model Files/
| |-- TEPLED5MM.DLL 289.5 KB the 5 mm LEDs, to MODELS
| |-- TEPNET.DLL 2.96 MB the board + monitors + network, to MODELS
| |-- TEPPASSIVE.DLL 288.5 KB the passive buzzer, to MODELS
| |-- TEPRESISTOR.DLL 311.0 KB the resistors, to MODELS
|-- Arduino Code/
| |-- DK54LM_BLE_Crossing/DK54LM_BLE_Crossing.ino 5.6 KB the demo sketch
| |-- TEP Boards for Proteus/hardware/ 1.29 MB the Arduino IDE add-on 1.86.0 (307 files)
|-- Proteus Simulation/
| |-- DK54LM_BLE_Crossing.hex 33.6 KB the demo sketch (U1)
| |-- nRF54LM20-DK-BLE-Pedestrian-Crossing.pdsprj 24.9 KB the demo: a Bluetooth LE pedestrian crossing
| |-- TEPLED5MM.DLL 289.5 KB copy of the model
| |-- TEPNET.DLL 2.96 MB copy of the model
| |-- TEPPASSIVE.DLL 288.5 KB copy of the model
| |-- TEPRESISTOR.DLL 311.0 KB copy of the model
|-- README.txt ~13.0 KB this file
Total: 9.46 MB (unzipped). The source code of the models is not included.
WHAT IS IT?
Proteus 8 has no nRF54LM20 processor model, so this is NOT a real nRF54LM20 chip. Our team has put a lot of effort into
building this board ourselves: it is Nordic Semiconductor's nRF54LM20 DK (PCA10184) - the blue development kit with the
nRF54LM20 SoC (an Arm Cortex-M33 with a RISC-V coprocessor; Bluetooth LE, 802.15.4 for Thread and high-speed USB), its
PCB antenna, the interface MCU with its USB port, the external SPI flash, the power switch, four buttons and four green
LEDs - drawn compact, and it runs YOUR Arduino sketch in Proteus:
* You write a normal sketch and compile it in the Arduino IDE with our board package "TEP Boards for Proteus" 1.86.0
(in Arduino Code - see INSTALLATION). The kit has NO Arduino Uno header: its pins are the GPIOs on the port headers
P0, P1, P2 and P3, named as on the kit (P1_04 for P1.04, and so on) - the 32 GPIOs of Zephyr's board files for the
kit (the expansion header, the LEDs, the buttons and UART30).
* LED0 .. LED3 are lit when HIGH, as on the real kit (LED_BUILTIN is LED0). BUTTON0 .. BUTTON3 read LOW while you
hold them: click a button on the board in the running simulation. They are GPIOs on the headers, as on the kit.
* Bluetooth LE works through ArduinoBLE: the board advertises as a peripheral with your services and
characteristics, and our Mobile WiFi Monitor's Bluetooth app is the central (it lists the board, connects, reads,
writes and gets the notifications).
TEP additions: the USB port opens the serial monitor (the same window as our TEP Serial Monitor Advance). Our choices
for the Arduino buses: Serial1 = UART30 (TX P0.06, RX P0.07 - the kit's own), A0 .. A3 = P1.04 .. P1.07, SDA / SCL =
P1.02 / P1.03, SPI SCK / MOSI / MISO / SS = P2.01 / P2.02 / P2.04 / P2.05.
Limits (say them before you start): one phone is the central; the board cannot be a central itself. 802.15.4 /
Thread, the RISC-V coprocessor, USB device classes (the SoC's own USB port) and the external flash are drawn, not
modelled. Your sketch gets 8 KB of RAM in the simulation, about 256 KB of flash, and int is 16 bits in the simulation
(use long for big numbers). See MODEL SCOPE AND LIMITS
Modelled: the 32 GPIOs; digital I/O, analogRead 0 .. 1023 (A0 .. A3), PWM (analogWrite), pulse timing, tone and
attachInterrupt through the board model; Serial (the board's monitor), Serial1, Wire and SPI; the four LEDs, the four
buttons and RESET; Bluetooth LE as a peripheral (ArduinoBLE) with the phone as the central.
Not modelled: the nRF54LM20 itself, its coprocessor, the radio's range, 802.15.4 / Thread, USB device classes, the
external flash, the board as a central. The simulation runs below real time.
ONE DEVICE (search "NRF54LM20" in Pick Devices):
NRF54LM20 DK "nRF54LM20 DK" V1.0 (Microprocessor ICs > Bluetooth Boards), prefix U, model TEPNET.DLL.
Its TEP window has no Windows title bar: the serial monitor (the USB port, 115200 baud: Monitor, Plotter and Board
tabs).
The same TEPNET.DLL also runs our other sketch boards and the phone; it replaces any older TEPNET.DLL (keep only this
newest one in MODELS).
TEST STATUS
V1.0: verified in Proteus 8.5 on 18 Nov 2026 with the demo project as shipped. What the Proteus run showed:
* nRF54LM20-DK-BLE-Pedestrian-Crossing: "Advertising as "nRF54LM20 Crossing"", ">> CARS GO" (the green LED); the
phone's Bluetooth app, SCAN, connect: "Phone connected", the state and the crossings on the phone.
* BUTTON0 "Request: the pedestrians are waiting", ">> YELLOW", ">> WALK (crossing 1)" (the red LED, LED0 .. LED3
counting down, the buzzer ticking), ">> CLEARING", ">> CARS GO".
* BUTTON1 ">> NIGHT" (the yellow LED flashing); BUTTON0 in the night "Request (night mode: it waits)"; BUTTON1
"Night mode off", ">> CARS GO".
* about 48 s of simulation, no errors, with the phone and the monitor open.
INSTALLATION (about 3 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" to the LIBRARY folder of Proteus, for example:
C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
(on some PCs: C:\ProgramData\Labcenter Electronics\Proteus 8 Professional\LIBRARY). TEPNRF54LM20DK.LIB is the board;
TEPLED5MM.LIB, TEPPASSIVE.LIB and TEPRESISTOR.LIB are the demo's LEDs, buzzer and resistors, TEPMOBILE.LIB and
TEPLAPTOP.LIB the phone and the laptop.
3. Copy the DLLs from "Proteus Model Files" (TEPNET.DLL, TEPLED5MM.DLL, TEPPASSIVE.DLL, TEPRESISTOR.DLL) to the MODELS
folder (...\Proteus 8 Professional\MODELS) - replace an older TEPNET.DLL (the first one that knows this board).
4. Delete TEPNRF54LM20DK.IDX from the LIBRARY folder if it is there.
5. The Arduino IDE (only to compile your own sketches - the demo has its HEX file): copy the folder
"Arduino Code\TEP Boards for Proteus\hardware" into your sketchbook folder (normally Documents\Arduino), so that
Documents\Arduino\hardware\tep\avr\boards.txt exists (replace an older copy); restart the IDE. The Arduino AVR Boards
platform must be installed (it comes with IDE 1.8.x; in IDE 2.x install "Arduino AVR Boards" from the Boards
Manager once).
Tools > Board > TEP Boards for Proteus > Nordic nRF54LM20 DK (TEP Proteus). ArduinoBLE is in the board package.
6. Start Proteus. In Pick Devices (P) search "NRF54LM20".
RUN THE DEMO
Keep the .hex file and the DLLs beside the project in "Proteus Simulation".
nRF54LM20-DK-BLE-Pedestrian-Crossing.pdsprj - U1 the nRF54LM20 DK (DK54LM_BLE_Crossing.hex) is a push-button pedestrian
crossing: the cars' light = our 5 mm LEDs D1 RED (P3.00), D2 YELLOW (P3.01), D3 GREEN (P3.02), each through 220 ohm;
BZ1 = our passive buzzer through 100 ohm on P3.03; MOB1 = the phone (Mobile WiFi Monitor), whose Bluetooth app
connects to it.
Press Run. The monitor prints "Advertising as "nRF54LM20 Crossing"" and ">> CARS GO" (the green LED). On the phone open
the Bluetooth app, press SCAN and connect: it shows the state, the crossings and a waiting request. Click BUTTON0 (the
pedestrians' request): after at least 4 s of green the cars get YELLOW (2 s), then RED, and the pedestrians WALK for
8 s - LED0 .. LED3 count the time down and the buzzer ticks (faster in the last 2 s); then CLEARING and CARS GO again.
BUTTON1 switches the night mode on / off (the yellow LED flashes; a request waits).
Closed a window? The USB port opens the monitor, a click on the phone's screen the phone.
THE PINS (the label on the part, what it can do in the simulation; the real kit's GPIO from Zephyr's nrf54lm20dk)
P0.03, P0.04 GPIO, PWM, interrupt, pulse timing (expansion header)
P0.05 BUTTON3 (LOW when pressed)
P0.06, P0.07 Serial1 TX and RX (the kit's UART30), or GPIO
P1.02, P1.03 Wire SDA and SCL (our choice), or GPIO
P1.04 .. P1.07 A0 .. A3: analogRead 0 .. 1023 for 0 .. 3.3 V (our choice), or GPIO
P1.08, P1.09 BUTTON2, BUTTON1 (LOW when pressed)
P1.13 GPIO, PWM, interrupt (expansion header)
P1.22 P1.25 P1.27 P1.28 LED0, LED1, LED2, LED3 (lit when HIGH); P1.26 BUTTON0
P2.00 .. P2.05 GPIO; SPI SCK P2.01, MOSI P2.02, MISO P2.04, SS P2.05 (our choice)
P3.00 .. P3.06 GPIO, PWM, interrupt, pulse timing (expansion header)
VDD, 5V, GND 3.3 V (the logic), 5 V, ground
The core numbers (the order on the headers): P0.03 .. P0.07 = 0 .. 4, P1.02 .. P1.09 = 5 .. 12, P1.13 = 13,
P1.22 P1.25 P1.26 P1.27 P1.28 = 14 .. 18, P2.00 .. P2.05 = 19 .. 24, P3.00 .. P3.06 = 25 .. 31. Serial is the USB: the
board's built-in monitor.
PROPERTIES (double-click the part > Edit Properties)
PROGRAM the sketch's HEX (Arduino IDE: Sketch > Export Compiled Binary, board Nordic nRF54LM20 DK)
MONITOR YES = the built-in serial monitor on Serial; BAUD its speed (115200, or AUTO)
AUTOOPEN YES = the monitor window opens at Run (the demo: YES)
TROUBLESHOOTING
* The phone's list is empty: call BLE.begin(), set a local name and BLE.advertise(); call BLE.poll() in loop().
* An LED stays dark: each 5 mm LED needs its resistor and its cathode (K) to ground; the pins are P3.00 .. P3.02.
* A button does nothing: use pinMode(BUTTONx, INPUT_PULLUP) and act when digitalRead() is LOW.
* An LED stays dark: the nRF54LM20 DK's LEDs light when the pin is HIGH.
* An integer goes wrong above 32767: int is 16 bits in the simulation - use long.
BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot and the Serial Monitor text:
https://www.theengineeringprojects.com/forum
LICENCES AND THIRD-PARTY NOTES
* The board model (TEPNET.DLL), the symbols and artwork (TEPNRF54LM20DK.LIB) and the LED, buzzer and resistor models
are made by The Engineering Projects. The source code of the models is not included.
* TEP Boards for Proteus (Arduino Code): its core, the variants and the EEPROM, SPI and Wire libraries are modified
copies of the Arduino AVR core 1.8.6 - GNU Lesser General Public License 2.1 (LGPL 2.1, the text:
LICENSE-LGPL-2.1.txt); its ArduinoBLE and the others and our core files are MIT (LICENSE-MIT.txt).
* Our ArduinoBLE has the calls of the library of that name; its code is ours.
* Proteus is a product of Labcenter Electronics and is not included. nRF54LM20 and Nordic Semiconductor are names of
Nordic Semiconductor ASA, Arduino of Arduino. The Bluetooth word mark belongs to Bluetooth SIG. This library is not
made or endorsed by them or by Labcenter.
REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied. Install TEP Boards for Proteus (INSTALLATION step 5), open Arduino Code\DK54LM_BLE_Crossing,
select Nordic nRF54LM20 DK (TEP Proteus) and use Sketch > Export Compiled Binary. For a real kit use Nordic's nRF
Connect SDK (Zephyr with the board nrf54lm20dk/nrf54lm20a/cpuapp). Its pins work at 3.3 V.
MODEL SCOPE AND LIMITS
Modelled: the 32 GPIOs; digital I/O, analogRead 0 .. 1023 (A0 .. A3), PWM (analogWrite), pulse timing, tone and
attachInterrupt through the board model; Serial (the board's monitor), Serial1, Wire and SPI; the four LEDs, the four
buttons and RESET; Bluetooth LE as a peripheral (ArduinoBLE) with the phone as the central.
Not modelled: the nRF54LM20 itself, its coprocessor, the radio's range, 802.15.4 / Thread, USB device classes, the
external flash, the board as a central. The simulation runs below real time.
VERSION
TEP nRF54LM20 DK library V1.0 (Nov 2026). Device NRF54LM20 DK (TEPNRF54LM20DK.LIB / TEPNET.DLL), TEP Boards for Proteus
1.86.0 (adds this board: the P0 .. P3 GPIOs, LED0 .. LED3, BUTTON0 .. BUTTON3).
Demo sketch DK54LM_BLE_Crossing V1.0. Demo parts: LED5MMREDTEP, LED5MMYELLOWTEP, LED5MMGREENTEP, BUZZERPASSIVETEP,
RESISTOR4BANDTEP and MOBILE WIFI MONITOR.Development1 release
-
V1.0nRF54LM20 DK Library for Proteus V1.0this page
V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.
Installation10 steps
From the download to a working project, in order. The steps follow what the package contains.
You will need
- Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
- Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
- The compiler named in the tutorialto build the source files into firmware
- Any archive toolWindows, macOS and Linux extract ZIP files on their own
Steps
- 1
Extract the archive
Right-click 4e92157fbff7481a9896b1576f622730.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (nRF54LM20-DK-TEP-v1.0) as it is.
- 2
Copy the library files into Proteus
Move TEPLAPTOP.LIB, TEPLED5MM.LIB and TEPMOBILE.LIB and 3 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.
- 3
Add the simulation model
Copy TEPLED5MM.DLL, TEPNET.DLL and TEPPASSIVE.DLL and 1 more into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.
- 4
Restart Proteus and place the component
Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.
- 5
Install the Arduino library
In the Arduino IDE choose Sketch → Include Library → Add .ZIP Library and pick the library, or copy its folder into Documents\Arduino\libraries. Restart the IDE to see its examples.
- 6
Open the sketch in the Arduino IDE
Open DK54LM_BLE_Crossing.ino, eeprom_clear.ino and eeprom_crc.ino and 17 more, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.
- 7
Build the source code
Open abi.cpp, Arduino.h and binary.h and 52 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.
- 8
Load the HEX file
In Proteus double-click the microcontroller, set Program File to DK54LM_BLE_Crossing.hex and run the simulation. For real hardware, flash the same file with your programmer.
- 9
Open the example simulation
Open nRF54LM20-DK-BLE-Pedestrian-Crossing.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.
- 10
Follow the tutorial
nRF54LM20 DK Library for Proteus: nRF54LM20 Bluetooth LE Simulation explains every connection and setting in order; keep it open beside the files while you build.
FAQs9 questionsContact TEP
How do I download nRF54LM20 DK Library for Proteus V1.0?
Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.
What is inside the archive?
nRF54LM20 DK Library for Proteus V1.0 comes as a ZIP archive of 325 files (4.2 MB, 9.5 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code. Open the File Structure tab for the full list of 325 files.
What should I do if the download does not start?
Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.
Is this file free?
Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.
How do I check that the file arrived complete?
Compare its SHA-256 with the one on this page, 6a17e87fa50296f9b298e831f94195d01cfddc236178e095318fb1a2421fb3a8. In PowerShell run Get-FileHash "4e92157fbff7481a9896b1576f622730.zip"; on macOS or Linux run shasum -a 256 "4e92157fbff7481a9896b1576f622730.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.
Do I need WinRAR to open the ZIP file?
No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.
Where do I put the LIB and IDX files?
Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.
Which Proteus version does the library need?
The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.
How do I get the HEX file into the simulation?
Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.
Members skip the wait. Log in or join TEP.
- 0Total downloads
- 4%Popularity
- ProteusCategory
- 0Comments
- ssyedzainnasirUploaded by
- 21 Nov 2026Uploaded at
6a17e87fa50296f9b298e831f94195d01cfddc236178e095318fb1a2421fb3a8






















Comments
0