Project Files of nRF9160 DK Library for Proteus: Cellular SMS Simulation
6f93a7b8d6f2450da57c1e28ab83fd46.zip

nRF9160 DK Library for Proteus V1.0
nRF9160 DK Library for Proteus V1.0 comes as a ZIP archive of 323 files (3.9 MB, 8.9 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code.
- LIBProteus library
- DLLProteus model
- DSNProteus simulation
- INOArduino sketch
- LIBArduino library
- HEXHEX firmware
- SRCSource code
Description
nRF9160-DK-Library-for-Proteus-v1.0.zip with Nordic's nRF9160 DK in Proteus (your sketch with the LTE-M / NB-IoT modem on SerialModem - SMS - LED1 .. LED4, BUTTON1 / BUTTON2 and a serial monitor; TEPNRF9160DK.LIB, TEPNET.DLL and the TEP Boards for Proteus add-on 1.87.0), the NTC thermistor and resistor libraries, the frost alarm demo and a README.
File Structure
8.2 KB1.1 KB7.7 KB11 KB8.5 KB1.5 KB1.7 KB1.9 KB5.7 KB4.9 KB1.1 KB5.8 KB9.6 KB7.2 KB2.5 KB2.1 KB1.9 KB2.1 KB4.4 KB1.1 KB3 KB3 KB1.8 KB2.5 KB3.5 KB149 B2.7 KB2 KB6.4 KB3.2 KB1.3 KB963 B8.6 KB5.9 KB6 KB12 KB1.6 KB1.3 KB14.7 KB4.3 KB6.1 KB20.1 KB8.2 KB2 KB4.5 KB311 B12.8 KB6.7 KB6.1 KB2.2 KB3.4 KB5.9 KB1.5 KB1.6 KB16.6 KB9.7 KB6.9 KB2.1 KB533 B5.7 KB7.4 KB514 B1.7 KB896 B481 B1.4 KB1012 B482 B936 B559 B467 B3.6 KB3.8 KB504 B956 B575 B455 B8.3 KB10.9 KB522 B79 B5.5 KB3.1 KB79 B442 B918 B1.4 KB1.8 KB1 KB1.3 KB1.4 KB1.8 KB1.4 KB5.7 KB502 B463 B5 KB6.5 KB3.4 KB3.4 KB500 B1.6 KB368 B406 B466 B404 B444 B460 B477 B739 B448 B1.3 KB350 B5.7 KB4 KB562 B1.5 KB2 KB550 B7.2 KB4.1 KB371 B4.5 KB3.5 KB492 B390 B478 B6.6 KB2.4 KB479 B5.1 KB1.9 KB1.3 KB1.3 KB750 B1.3 KB490 B2.2 KB1.9 KB498 B1.2 KB1.2 KB487 B5.1 KB4.6 KB371 B3.6 KB2.5 KB534 B1.5 KB1.2 KB478 B6.2 KB3 KB1.5 KB1.7 KB469 B1 KB1.7 KB433 B294 B358 B1.3 KB2.5 KB13.2 KB3.8 KB659 B510 B4.4 KB1.9 KB5.8 KB11 KB835 B518 B308 B1.3 KB3.3 KB568 B6.4 KB2.3 KB29 B436 B9.2 KB4.9 KB439 B4.2 KB1.5 KB9.3 KB7.1 KB4.7 KB2.4 KB388 B5.1 KB893 B667 B1.3 KB5.5 KB2.3 KB1.8 KB468 B882 B530 B791 B487 B894 B2 KB730 B646 B2.6 KB977 B702 B20.6 KB1.8 KB11.8 KB3.2 KB596 B406 B6.3 KB5.7 KB9.3 KB7.7 KB7.7 KB6.1 KB5.8 KB5.9 KB6.4 KB6.4 KB5.3 KB5.6 KB5.7 KB7.9 KB7.7 KB6.5 KB6.3 KB6.2 KB6.4 KB5.9 KB10.3 KB8.5 KB6.6 KB7.6 KB6.7 KB6.1 KB6.7 KB8.3 KB6.2 KB7.2 KB6.2 KB5.9 KB5.6 KB5.7 KB6.7 KB5.9 KB6.2 KB6 KB6 KB6.1 KB6.3 KB6 KB6.1 KB6.2 KB6 KB5.8 KB6.4 KB6.4 KB3.8 KB6.4 KB7.3 KB6.4 KB4 KB6.9 KB7.7 KB6 KB6.8 KB6.9 KB7 KB6.3 KB6.4 KB6.5 KB6.5 KB6.6 KB6.5 KB5.9 KB6.1 KB5.6 KB6.6 KB5.9 KB7.5 KB3.8 KB4.4 KB5.4 KB7.7 KB7.1 KB5.8 KB5.9 KB5.9 KB6.9 KB5.7 KB5.9 KB5.8 KB5.5 KB5.5 KB7.1 KB5.2 KB42.8 KB25.9 KB1.3 KB8.5 KB37.7 KB39.5 KB13.1 KB40.2 KB14.3 KB306.9 KB3.0 MB288.5 KB311 KB47.4 KB22 KB3.0 MB288.5 KB311 KB12.7 KBGallery12 images from the tutorialOpen the tutorial
The circuit, the board and the results as they appear in nRF9160 DK Library for Proteus: Cellular SMS Simulation. Open an image for its full size.












README
NRF9160 DK LIBRARY FOR PROTEUS - V1.0 (YOUR ARDUINO SKETCH, THE LTE-M / NB-IOT MODEM WITH SMS, FOUR LEDS)
Designed by The Engineering Projects
www.TheEngineeringProjects.com
IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
https://www.theengineeringprojects.com/2026/11/nrf9160-dk-library-for-proteus.html
Report a bug or suggest a feature (our forum):
https://www.theengineeringprojects.com/forum
The demo's other parts are our libraries (included) - their articles:
https://www.theengineeringprojects.com/2026/11/ntc-thermistor-library-for-proteus.html
https://www.theengineeringprojects.com/2026/11/resistor-library-for-proteus.html
Support us (the libraries are free):
https://www.theengineeringprojects.com/donate
FILE STRUCTURE
nRF9160-DK-TEP-v1.0/
|-- Proteus Library Files/
| |-- TEPLAPTOP.LIB 39.5 KB the laptop (demo), to LIBRARY
| |-- TEPMOBILE.LIB 13.1 KB the phone (demo), to LIBRARY
| |-- TEPNRF9160DK.LIB 40.2 KB the nRF9160 DK, to LIBRARY
| |-- TEPNTC.LIB 14.3 KB the NTC thermistor (demo), to LIBRARY
| |-- TEPRESISTOR.LIB 306.9 KB the resistor (demo), to LIBRARY
|-- Proteus Model Files/
| |-- TEPNET.DLL 2.96 MB the board + monitors + network, to MODELS
| |-- TEPNTC.DLL 288.5 KB the NTC thermistor, to MODELS
| |-- TEPRESISTOR.DLL 311.0 KB the resistor, to MODELS
|-- Arduino Code/
| |-- DK9160_SMS_Frost_Alarm/DK9160_SMS_Frost_Alarm.ino 8.2 KB the demo sketch
| |-- TEP Boards for Proteus/hardware/ 1.30 MB the Arduino IDE add-on 1.87.0 (308 files)
|-- Proteus Simulation/
| |-- DK9160_SMS_Frost_Alarm.hex 47.4 KB the demo sketch (U1)
| |-- nRF9160-DK-SMS-Frost-Alarm.pdsprj 22.0 KB the demo: a cellular SMS frost alarm
| |-- TEPNET.DLL 2.96 MB copy of the model
| |-- TEPNTC.DLL 288.5 KB copy of the model
| |-- TEPRESISTOR.DLL 311.0 KB copy of the model
|-- README.txt ~12.3 KB this file
Total: 8.89 MB (unzipped). The source code of the models is not included.
WHAT IS IT?
Proteus 8 has no nRF9160 processor model, so this is NOT a real nRF9160 chip. Our team has put a lot of effort into
building this board ourselves: it is Nordic Semiconductor's nRF9160 DK (PCA10090) - the blue development kit with the
nRF9160 SiP (Nordic's first cellular IoT system-in-package: the processor, the LTE-M / NB-IoT modem and GPS under one
shield), the nano-SIM holder, the LTE and GPS antennas, the nRF52840 board controller, the interface MCU with its USB
port, the power switch, four green LEDs, two buttons and two slide switches - drawn compact, and it runs YOUR Arduino
sketch in Proteus:
* You write a normal sketch for the DK's Arduino header (D0 .. D13, A0 .. A5, SDA, SCL; analogRead 0-1023,
analogWrite, attachInterrupt, tone, Wire, SPI, Serial) and compile it in the Arduino IDE with our board package
"TEP Boards for Proteus" 1.87.0 (in Arduino Code - see INSTALLATION).
* The modem answers AT commands on SerialModem (115200 baud): registration (AT+CEREG?), SMS in text mode (AT+CMGF=1,
AT+CMGS, AT+CNMI and +CMT), and GNSS (AT+CGPS=1,1, AT+CGPSINFO). MODEM_ON HIGH starts it. On the real chip the
application starts the modem with Nordic's modem library and sends the same kind of AT commands through it.
* The board's Phone window is the other end: the owner's phone receives the board's SMS, sends SMS (with four quick
keys: STATUS, LIMIT UP, LIMIT DOWN, HELP) and sets the network and the GNSS scene.
* LED1 .. LED4 light when HIGH, as on the real DK (LED_BUILTIN is LED1). BUTTON1 / BUTTON2 read LOW while you hold
them: click a button on the board in the running simulation.
TEP additions: the USB port opens the serial monitor (the same window as our TEP Serial Monitor Advance); the small
LTE LED shows the modem's network light (its blink changes when the modem registers); a click on the SiP opens the
modem's window.
Limits (say them before you start): there is no Bluetooth in the nRF9160, and the nRF52840 board controller is drawn,
not modelled. Voice calls, data (IP, MQTT, CoAP), PSM and eDRX timers are not modelled; SMS is text mode only. SWITCH1 /
SWITCH2 are drawn, not modelled. Your sketch gets 8 KB of RAM in the simulation, about 256 KB of flash, and int is 16
bits in the simulation (use long for big numbers). See MODEL SCOPE AND LIMITS.
ONE DEVICE (search "NRF9160" in Pick Devices):
NRF9160 DK "nRF9160 DK" V1.0 (Microprocessor ICs > Cellular Boards), prefix U, model TEPNET.DLL.
Its TEP windows have no Windows title bar: the serial monitor (the USB port, 115200 baud: Monitor, Plotter and Board
tabs) and the modem's window (a click on the SiP).
The same TEPNET.DLL also runs our other sketch boards and the phone; it replaces any older TEPNET.DLL (keep only this
newest one in MODELS).
TEST STATUS
V1.0: verified in Proteus 8.5 on 18 Nov 2026 with the demo project as shipped. What the Proteus run showed:
* nRF9160-DK-SMS-Frost-Alarm: "Starting the nRF9160 modem", "Modem ready", the LTE LED searching,
"LTE: registered on the network" (LED1, the search took 2.88 s), the SMS "Frost alarm online: 25.0 C, limit 3.0 C,
no frost, alarms 0".
* the NTC's Ice: 14.3 C, 3.5 C, then ">> FROST: 2.6 C" (LED2) and the SMS "FROST ALARM 1: 2.6 C (limit 3.0 C)".
* the Phone window's STATUS: "1.3 C, limit 3.0 C, FROST, alarms 1"; LIMIT UP: "Limit 3.5 C, now 0.8 C".
* the NTC's Room: ">> Frost over: 4.9 C" (LED4) by SMS; BUTTON1 the status, BUTTON2 "TEST ALARM: 12.2 C ...".
* about 52 s of simulation, no errors, 7 SMS sent and 2 received, with the Phone window, the NTC and the monitor open.
INSTALLATION (about 3 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" to the LIBRARY folder of Proteus, for example:
C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
(on some PCs: C:\ProgramData\Labcenter Electronics\Proteus 8 Professional\LIBRARY). TEPNRF9160DK.LIB is the board;
TEPNTC.LIB and TEPRESISTOR.LIB are the demo's NTC thermistor and resistor, TEPMOBILE.LIB and TEPLAPTOP.LIB for your
own designs.
3. Copy the DLLs from "Proteus Model Files" (TEPNET.DLL, TEPNTC.DLL, TEPRESISTOR.DLL) to the MODELS folder
(...\Proteus 8 Professional\MODELS) - replace an older TEPNET.DLL (this one is the first that knows this board).
4. Delete TEPNRF9160DK.IDX from the LIBRARY folder if it is there.
5. The Arduino IDE (only to compile your own sketches - the demo has its HEX file): copy the folder
"Arduino Code\TEP Boards for Proteus\hardware" into your sketchbook folder (normally Documents\Arduino), so that
Documents\Arduino\hardware\tep\avr\boards.txt exists (replace an older copy); restart the IDE. The Arduino AVR Boards
platform must be installed (it comes with IDE 1.8.x; in IDE 2.x install "Arduino AVR Boards" from the Boards
Manager once).
Tools > Board > TEP Boards for Proteus > Nordic nRF9160 DK (TEP Proteus). The demo needs no other library.
6. Start Proteus. In Pick Devices (P) search "NRF9160".
RUN THE DEMO
Keep the .hex file and the DLLs beside the project in "Proteus Simulation".
nRF9160-DK-SMS-Frost-Alarm.pdsprj - U1 the nRF9160 DK (DK9160_SMS_Frost_Alarm.hex) is a cellular frost alarm: VCC - R1
(47k) - A0 - RT1 (our 10k NTC thermistor, true scale) - GND; the owner's phone is the board's own Phone window (it
opens at Run).
Press Run. The monitor prints "Starting the nRF9160 modem", then "Modem ready"; the LTE LED blinks while the modem
searches. "LTE: registered on the network" lights LED1, and the board sends "Frost alarm online" with the temperature
(LED3 lights while an SMS goes out; LED4 = above the limit). In the NTC's window click Ice (0 C): the bead cools in
a few seconds; below the limit (3.0 C) LED2 lights and a FROST ALARM goes out by SMS; Room (25 C) warms it again: "Frost
over". In the Phone window press STATUS for a report and LIMIT UP / LIMIT DOWN to move the limit by 0.5 C. On the
board, BUTTON1 sends the status and BUTTON2 a test alarm.
Closed a window? The USB port opens the monitor, the SiP the Phone window, a click on the NTC its window.
THE PINS (the label on the part, what it can do in the simulation)
D0, D1 GPIO (Serial1 is the modem's AT interface: SerialModem)
D2 .. D13 GPIO, PWM (analogWrite), interrupt; D10 .. D13 SPI (SS, MOSI, MISO, SCK)
A0 .. A5 analogRead 0 .. 1023 for 0 .. 3.3 V, or GPIO (the core's numbers 14 .. 19)
SDA, SCL Wire
VDD, 5V, GND 3.3 V (the logic), 5 V, ground; RESET the board's reset (the RESET button too)
AREF, VIN drawn, not modelled
LED1 .. LED4 (22 .. 25) are the green LEDs, lit when HIGH; LED_BUILTIN is LED1, with LED_BUILTIN_ACTIVE and
LED_BUILTIN_INACTIVE. BUTTON1 / BUTTON2 (26 / 27) are the buttons, LOW when pressed (pinMode INPUT_PULLUP);
BTN_BUILTIN is BUTTON1. MODEM_ON (30) starts the modem. Serial is the USB: the board's built-in monitor. The real
board (Zephyr's nrf9160dk): LED1 .. LED4 = P0.02 .. P0.05, BUTTON1 / BUTTON2 = P0.06 / P0.07, SWITCH1 / SWITCH2 =
P0.08 / P0.09 - on the real board they share D2 .. D9; in the library the header pins stay free.
PROPERTIES (double-click the part > Edit Properties)
PROGRAM the sketch's HEX (Arduino IDE: Sketch > Export Compiled Binary, board Nordic nRF9160 DK (TEP Proteus))
MONITOR YES = the built-in serial monitor on Serial; BAUD its speed (115200, or AUTO)
AUTOOPEN YES = the monitor window opens at Run (the demo: YES)
TROUBLESHOOTING
* The modem never answers: set MODEM_ON HIGH and SerialModem.begin(115200) first; send AT until it answers OK.
* No SMS arrives: AT+CMGF=1 (text mode) and AT+CNMI=2,2,0,0,0 make a new SMS come straight to SerialModem as +CMT.
* The temperature looks wrong: the NTC is the lower half of the divider (47k from VCC to A0, the NTC from A0 to GND).
* The LEDs look inverted: on this DK they light when the pin is HIGH.
* An integer goes wrong above 32767: int is 16 bits in the simulation - use long.
BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot and the Serial Monitor text:
https://www.theengineeringprojects.com/forum
LICENCES AND THIRD-PARTY NOTES
* The board model (TEPNET.DLL, with its modem), the symbols and artwork (TEPNRF9160DK.LIB) and the NTC thermistor and
resistor models are made by The Engineering Projects. The source code of the models is not included.
* TEP Boards for Proteus (Arduino Code): its core, the variants and the EEPROM, SPI and Wire libraries are modified
copies of the Arduino AVR core 1.8.6 - GNU Lesser General Public License 2.1 (LGPL 2.1, the text:
LICENSE-LGPL-2.1.txt); its WiFi, WebServer, ArduinoBLE, the sensor libraries and the others and our core files are
MIT (LICENSE-MIT.txt).
* Proteus is a product of Labcenter Electronics and is not included. nRF9160, nRF52840 and Nordic Semiconductor are
names of Nordic Semiconductor ASA, Arduino of Arduino. This library is not made or endorsed by them or by Labcenter.
REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied. Install TEP Boards for Proteus (INSTALLATION step 5), open Arduino
Code\DK9160_SMS_Frost_Alarm, select Nordic nRF9160 DK (TEP Proteus) and use Sketch > Export Compiled Binary. For a real
board use Nordic's nRF Connect SDK with its modem library and SMS library; a SIM with an LTE-M or NB-IoT plan is
needed. Its pins work at 1.8 or 3.3 V.
MODEL SCOPE AND LIMITS
Modelled: the DK's Arduino header; digital I/O, analogRead 0 .. 1023, PWM (analogWrite), tone and attachInterrupt
through the board model; Serial (the board's monitor), Wire and SPI; the four LEDs, the two buttons and RESET; the
modem's AT interface with registration, SMS (text mode) and GNSS, with the phone as the other end.
Not modelled: the nRF9160 itself, the nRF52840 board controller, the radio and its coverage, data connections (IP,
MQTT, CoAP), voice, PSM and eDRX, the SIM's PIN, SWITCH1 / SWITCH2, the current measurement header. The simulation
runs below real time.
VERSION
TEP nRF9160 DK library V1.0 (Nov 2026). Device NRF9160 DK (TEPNRF9160DK.LIB / TEPNET.DLL), TEP Boards for Proteus
1.87.0 (adds this board: LED1 .. LED4, BUTTON1 / BUTTON2, SerialModem, MODEM_ON).
Demo sketch DK9160_SMS_Frost_Alarm V1.0. Demo parts: NTCBEAD10KTEP and RESISTOR4BANDTEP.Development1 release
-
V1.0nRF9160 DK Library for Proteus V1.0this page
V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.
Installation10 steps
From the download to a working project, in order. The steps follow what the package contains.
You will need
- Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
- Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
- The compiler named in the tutorialto build the source files into firmware
- Any archive toolWindows, macOS and Linux extract ZIP files on their own
Steps
- 1
Extract the archive
Right-click 6f93a7b8d6f2450da57c1e28ab83fd46.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (nRF9160-DK-TEP-v1.0) as it is.
- 2
Copy the library files into Proteus
Move TEPLAPTOP.LIB, TEPMOBILE.LIB and TEPNRF9160DK.LIB and 2 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.
- 3
Add the simulation model
Copy TEPNET.DLL, TEPNTC.DLL and TEPRESISTOR.DLL into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.
- 4
Restart Proteus and place the component
Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.
- 5
Install the Arduino library
In the Arduino IDE choose Sketch → Include Library → Add .ZIP Library and pick the library, or copy its folder into Documents\Arduino\libraries. Restart the IDE to see its examples.
- 6
Open the sketch in the Arduino IDE
Open DK9160_SMS_Frost_Alarm.ino, eeprom_clear.ino and eeprom_crc.ino and 17 more, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.
- 7
Build the source code
Open abi.cpp, Arduino.h and binary.h and 52 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.
- 8
Load the HEX file
In Proteus double-click the microcontroller, set Program File to DK9160_SMS_Frost_Alarm.hex and run the simulation. For real hardware, flash the same file with your programmer.
- 9
Open the example simulation
Open nRF9160-DK-SMS-Frost-Alarm.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.
- 10
Follow the tutorial
nRF9160 DK Library for Proteus: Cellular SMS Simulation explains every connection and setting in order; keep it open beside the files while you build.
FAQs9 questionsContact TEP
How do I download nRF9160 DK Library for Proteus V1.0?
Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.
What is inside the archive?
nRF9160 DK Library for Proteus V1.0 comes as a ZIP archive of 323 files (3.9 MB, 8.9 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code. Open the File Structure tab for the full list of 323 files.
What should I do if the download does not start?
Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.
Is this file free?
Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.
How do I check that the file arrived complete?
Compare its SHA-256 with the one on this page, 7ea19ce302896fc88ad38781609a46e3feede3186e95ecfb13690255877ab9b1. In PowerShell run Get-FileHash "6f93a7b8d6f2450da57c1e28ab83fd46.zip"; on macOS or Linux run shasum -a 256 "6f93a7b8d6f2450da57c1e28ab83fd46.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.
Do I need WinRAR to open the ZIP file?
No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.
Where do I put the LIB and IDX files?
Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.
Which Proteus version does the library need?
The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.
How do I get the HEX file into the simulation?
Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.
Members skip the wait. Log in or join TEP.
- 0Total downloads
- 4%Popularity
- ProteusCategory
- 0Comments
- ssyedzainnasirUploaded by
- 21 Nov 2026Uploaded at
7ea19ce302896fc88ad38781609a46e3feede3186e95ecfb13690255877ab9b1
















Comments
0