Hello everyone! I hope you all will be absolutely fine and having fun. Today I am going to elaborate you about Introduction to L298. L-298 is an Integrated Circuit (IC) available in two type of packages now a days which will be given later. L 298 is a dual full bridge driver that has a capability to bear high voltage as well as high current. It receives basic TTL (Transistor Transistor Logic) logic levels and is able to operate the different loads such as DC motors, stepper motors, relays etc. You should also have a look at Introduction to L23D.
L-298 has two enable input to control any device by enabling or disabling it. L 298 IC is most commonly used to make motor drivers or motor controllers. These motor controllers can be controlled by any ...
Hello everyone! I hope you will be absolutely fine and having fun. Today, I am going to explain all of you about Introduction to 74HC595. It is basically a shift register. It has an ability to store and to shift the data of 8 bits. First of all the data is written on the register serially and then it goes to the storage register. All of the output lines are controlled by this register.
74HC595 register is a very high speed device based on Complementary Metal Oxide Semiconductor (CMOS). 8 bit data register receives the data from the input DS. This data is then transferred from the input shift register to the output shift register. 74HC595 has a vey wide range of applications in daily life. It can be used as serial to parallel data converter, can ...
Hello friends, I hope you all are doing great. In today's tutorial, we are gonna have a look at detailed Introduction to TIP122. It is a Darlington braces NPN transistor. It works like an ordinary NPN transistor, but as it consists of a Darlington pair it has a decent collector current assessment of nearby 5 amperes and it's gain is around 1000. This transistor can bear 100 volts around collector and emitter terminals due to this feature it can be used for high loads.
This is a common purpose transistor it used in different industrial projects. It manufactured for less time taking switching submissions. In today’s post, we will have a look at its protection, wreck, distinction, entitlements, etc. I will also share some links where I have connecte ...
Hello everyone! I hope you all will be absolutely fine and having fun. Today, I am going to provide you the discussion on Introduction to LM393. LM-393 has two internal operational amplifiers. These are internally frequency compensated. These are specifically designed to perform their tasks using a single power supply sources. LM-393 can also perform its operations properly by using split power supply. The current drain supply does not depend upon the magnitude of the power supply.
One of the most amazing feature of LM 393 is that ground is included in its common mode input voltage. Moreover, LM 393 has a lot of features e.g. wide voltage supply ranges, a very small current drain supply, low input offset current, low input bias current, output v ...
Hello everyone! I hope you all will be absolutely fine and having fun. Today, I am going to tell you guys about Introduction to LM2902. LM2902 basically has four (4) internal builtin operational amplifiers. There builtin amplifiers are internally frequency compensated. The basic purpose behind designing this type of device is to support control systems in industries as well as automotive applications. LM-2902 is capable of operating for a wide range of voltages using a single power supply source.
Moreover, we can also operate this device from a split power source. Low current drain supply and magnitude of the power supply source, both are totally independent to each other. LM-2902 has a lot of features which make it different from the standard g ...
Hello everyone! I hope you all will be absolutely fine and having fun. Today, I am going to give a detailed discussion on Introduction to LF411. LF-411 is a Junction Field Effect Transistor (JFET) input Operational Amplifier (Op-amp). It is the most common module available in the market these days due to its cost efficiency. LF 411 has low input offset voltage. Input offset voltage drift is guaranteed for LF-411. A very low supply current is needed for this device. It provides higher slew rates as well as high gain bandwidth product.
Moreover, LF411 also provides lower input bias current as well as lower input offset currents. It is an 8 pin operational amplifier. The details about its pins will be discussed later. Due to its low cost and high ...
Hello friends! I hope you will be absolutely fine and having fun. Today, I am going to give you an elaboration about Introduction to 50N06. 50-N-06 is a device having three terminals named as gate, drain and source respectively. It is made up of silicon and is capable of current conduction up to 50A. I have already shared basic knowledge about different electronic devices in my previous articles like Introduction to MC34063, MMBD914, MSP430, NE555, NE556 and LM2902. Before going into the details of this article you must go through my previous tutorials for the better understanding.
50-N-06 provides fast switching speed. 50N06 is an N-channel power Metal Oxide Field Effect Transistor (MOSFET) specially designed to handle particular power levels. ...
Hi Guys! We always feel happy when you come over to browse useful information that meets with your needs and requirements. Electronic components used in electronic industry are the backbone of recent technology that make our lives easy and help us get rid of the most conventional ways of running electronic projects. Today, I am going to discuss the details on the Introduction to 1n5819. This is a metal to silicon power diode, also termed as Schottky Rectifier, that applies Schottky Barrier Principle. It is mainly used as rectifiers in high frequency low voltage inverters, polarity protection diodes and free wheeling diodes. I'll try to cover each and everything related to this transistor so you don't need to go anywhere and find all information ...
Hello everyone! I hope you will be absolutely fine and having fun. Today, I am going to give you an Introduction to 2N2222. It is the most commonly used Negative-Positive-Negative (NPN) Bipolar Junction Transistor (BJT) available in the market now a days. 2N2222 can be used for different purposes e.g. switching and amplification of analog signals. I hope you have enjoyed the previous post on Introduction to ULN2003.
The major functional area of 2N2222 is enclosed in TO-18 package. Due to the low cost and small size it is the most commonly used transistor. One of its key features is its ability to handle the high values of currents as compared to the other similar small transistors. Normally it is capable of switching a load current of 800mA whic ...
Hello friends, I hope you all are doing great. In today's tutorial, we are gonna have a look at detailed Introduction to C2383. C2383 is a silicon Epitaxial NPN Transistor, it is manufactured for color television to control the sound submissions. It is an expedient which operate on the high voltage the value of VCEO is 160 volts. It is corresponding to A1013 transistor in design.
It is assembled in TO-92 MOD type of casing and has the dimension of 210±20um 240um×240um. It manufactured by the famous electronic company of Toshiba. In today’s post, we will have a look at its fortification, smashup, prominence, proposals, etc. I will also share some links where I have correlated it with other microcontrollers. You can also get more material about it i ...
