TEP DOWNLOAD CENTER

Project Files of IoT Aquarium Controller with ESP32 - Proteus Simulation

Libraries Code Projects Simulation
tep://download-terminal a55701f537394423842dabedce1fcc8c.zip ZIP archiveV1.0Verified0 downloadsFree
IoT Aquarium Controller with ESP32 - Proteus Simulation: the ESP32, the DS18B20 probe, two 74HC595, the LED bar graph, the L9110S and the air pump
Proteus library · File 1 of 1

IoT Aquarium Controller with ESP32 - Proteus Simulation V1.0

IoT Aquarium Controller with ESP32 - Proteus Simulation V1.0 comes as a ZIP archive of 27 files (4.6 MB, 10.1 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware.

  • LIBProteus library
  • DLLProteus model
  • DSNProteus simulation
  • INOArduino sketch
  • HEXHEX firmware

Description

IoT-Aquarium-Controller-ESP32-Proteus-Simulation-v1.0.zip: the complete Proteus simulation project (ESP32 DevKit V1, DS18B20 probe, two 74HC595, the LED bar graph, L9110S, the mini air pump, resistors, the Laptop and Mobile WiFi Monitors), the Arduino sketch, every LIB and DLL the simulation needs and a README.

Read IoT Aquarium Controller with ESP32 - Proteus Simulation

File Structure

a55701f537394423842dabedce1fcc8c.zip27 files · 5 folders · 10.1 MB unpacked
ESP32-Aquarium-Controller-TEP-v1.0/27 files · 10.1 MB
Arduino Code/1 file · 8.8 KB
ESP32_Aquarium_Controller/1 file · 8.8 KB
INO ESP32_Aquarium_Controller.inoArduino sketch 8.8 KB
Proteus Library Files/9 files · 617.8 KB
LIB TEPAIRPUMP.LIBProteus library 13.5 KB
LIB TEPDS18B20.LIBProteus library 88 KB
LIB TEPESP32V1.LIBProteus library 36.6 KB
LIB TEPHC595.LIBProteus library 14.5 KB
LIB TEPL9110S.LIBProteus library 78.5 KB
LIB TEPLAPTOP.LIBProteus library 39.5 KB
LIB TEPLEDBAR.LIBProteus library 27.3 KB
LIB TEPMOBILE.LIBProteus library 13.1 KB
LIB TEPRESISTOR.LIBProteus library 306.9 KB
Proteus Model Files/7 files · 4.7 MB
DLL TEPAIRPUMP.DLLSimulation model 316.5 KB
DLL TEPDS18B20.DLLSimulation model 305 KB
DLL TEPHC595.DLLSimulation model 300.5 KB
DLL TEPL9110S.DLLSimulation model 295 KB
DLL TEPLEDBAR.DLLSimulation model 288.5 KB
DLL TEPNET.DLLSimulation model 2.9 MB
DLL TEPRESISTOR.DLLSimulation model 311 KB
Proteus Simulation/9 files · 4.8 MB
DSN ESP32-Aquarium-Controller.pdsprjProteus simulation 38.5 KB
HEX ESP32_Aquarium_Controller.hexCompiled HEX file 74.2 KB
DLL TEPAIRPUMP.DLLSimulation model 316.5 KB
DLL TEPDS18B20.DLLSimulation model 305 KB
DLL TEPHC595.DLLSimulation model 300.5 KB
DLL TEPL9110S.DLLSimulation model 295 KB
DLL TEPLEDBAR.DLLSimulation model 288.5 KB
DLL TEPNET.DLLSimulation model 2.9 MB
DLL TEPRESISTOR.DLLSimulation model 311 KB
TXT README.txtText file 11 KB

README

README.txt 151 lines
===============================================================================================================
  IoT Aquarium Controller with ESP32 - Proteus Simulation Project V1.0
  The Engineering Projects - www.TheEngineeringProjects.com
===============================================================================================================

IMPORTANT LINKS
  The project tutorial (circuit, code, simulation results):
    https://www.theengineeringprojects.com/2026/11/iot-aquarium-controller-esp32-proteus-simulation.html
  The libraries this project is built from (each post has its own full download and tutorial):
    ESP32 DevKit V1 board:
      https://www.theengineeringprojects.com/2026/10/esp32-devkit-v1-library-for-proteus-v2-0.html
    74HC595 shift register:
      https://www.theengineeringprojects.com/2026/11/74hc595-shift-register-library-for-proteus.html
    LED bar graph:
      https://www.theengineeringprojects.com/2026/11/led-bar-graph-library-for-proteus.html
    Mini air pump:
      https://www.theengineeringprojects.com/2026/11/mini-air-pump-library-for-proteus.html
    DS18B20 waterproof probe:
      https://www.theengineeringprojects.com/2026/10/ds18b20-library-for-proteus-v1-0.html
    L9110S motor driver:
      https://www.theengineeringprojects.com/2026/10/l9110s-motor-driver-library-for-proteus-v1-0.html
    Resistor:
      https://www.theengineeringprojects.com/2026/11/resistor-library-for-proteus.html
    Laptop WiFi Monitor:
      https://www.theengineeringprojects.com/2026/10/laptop-wifi-monitor-library-for-proteus.html
    Mobile WiFi Monitor:
      https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
  Support our free work: https://www.theengineeringprojects.com/donate

FILE STRUCTURE
ESP32-Aquarium-Controller-TEP-v1.0/
|-- Proteus Library Files/
|   |-- TEPAIRPUMP.LIB                                 13.5 KB   a part of the project -> LIBRARY folder
|   |-- TEPDS18B20.LIB                                 88.0 KB   a part of the project -> LIBRARY folder
|   |-- TEPESP32V1.LIB                                 36.6 KB   a part of the project -> LIBRARY folder
|   |-- TEPHC595.LIB                                   14.5 KB   a part of the project -> LIBRARY folder
|   |-- TEPL9110S.LIB                                  78.5 KB   a part of the project -> LIBRARY folder
|   |-- TEPLAPTOP.LIB                                  39.5 KB   a part of the project -> LIBRARY folder
|   |-- TEPLEDBAR.LIB                                  27.3 KB   a part of the project -> LIBRARY folder
|   |-- TEPMOBILE.LIB                                  13.1 KB   a part of the project -> LIBRARY folder
|   |-- TEPRESISTOR.LIB                               306.9 KB   a part of the project -> LIBRARY folder
|-- Proteus Model Files/
|   |-- TEPAIRPUMP.DLL                                316.5 KB   a model -> MODELS folder
|   |-- TEPDS18B20.DLL                                305.0 KB   a model -> MODELS folder
|   |-- TEPHC595.DLL                                  300.5 KB   a model -> MODELS folder
|   |-- TEPL9110S.DLL                                 295.0 KB   a model -> MODELS folder
|   |-- TEPLEDBAR.DLL                                 288.5 KB   a model -> MODELS folder
|   |-- TEPNET.DLL                                     2.89 MB   a model -> MODELS folder
|   |-- TEPRESISTOR.DLL                               311.0 KB   a model -> MODELS folder
|-- Proteus Simulation/
|   |-- ESP32_Aquarium_Controller.hex                  74.2 KB   the firmware
|   |-- ESP32-Aquarium-Controller.pdsprj               38.5 KB   the project simulation
|   |-- TEPAIRPUMP.DLL                                316.5 KB   copy of the model
|   |-- TEPDS18B20.DLL                                305.0 KB   copy of the model
|   |-- TEPHC595.DLL                                  300.5 KB   copy of the model
|   |-- TEPL9110S.DLL                                 295.0 KB   copy of the model
|   |-- TEPLEDBAR.DLL                                 288.5 KB   copy of the model
|   |-- TEPNET.DLL                                     2.89 MB   copy of the model
|   |-- TEPRESISTOR.DLL                               311.0 KB   copy of the model
|-- Arduino Code/
|   |-- ESP32_Aquarium_Controller/ESP32_Aquarium_Controller.ino    8.8 KB   the sketch (source of the .hex)
|-- README.txt                                        ~10.7 KB   this file
Total: 10.07 MB (unzipped). The C++ source code of the models is not included.

WHAT IS IT?
  An aquarium controller you can run in Proteus: an ESP32 measures the water's temperature, shows it on a 10-segment
  LED bar graph driven by two 74HC595 shift registers, runs the tank's air pump harder as the water warms (warm water
  holds less oxygen), stops it for feeding and serves a web dashboard.
    * DS18B20 waterproof probe (DS18B20PROBEADVTEP, U4): VDD on 3.3 V, DQ on D4 with R11 4.7 k to 3.3 V, GND (OneWire).
    * Two 74HC595 shift registers (SN74HC595TEP, U2 and U3), VCC 3.3 V: SER D23 (U2) and D21 (U3); SRCLK D18, RCLK D5
      and SRCLR D19 (held high by the sketch) shared; OE to GND. Both chips take their byte in the same 8 clocks.
    * 10-segment LED bar graph, green, yellow and red (LEDBAR10MIXTEP, BAR1): U2's QA - QH and U3's QA - QB through
      R1 - R10 (220 ohm) to the anodes A1 - A10; the cathodes K1 - K10 to GND.
    * L9110S motor driver (L9110SADVTEP, DRV1) on +6V: A-IA D25 (PWM), A-IB D26 (LOW); B-IA and B-IB to GND.
    * 6 V mini air pump (MINIAIRPUMPTEP, M1) on motor A: an air stone 30 cm under water.
    * ESP32 DEVKIT V1 (U1) runs ESP32_Aquarium_Controller.hex on TEP-WiFi at 192.168.1.101 (port 80).
    * Laptop WiFi Monitor (PC1) and Mobile WiFi Monitor (MOB1) open http://192.168.1.101/.
  The rules (at the top of the sketch):
    * the bar is a thermometer: one segment at 21 C, one more each degree, all ten at 30 C;
    * AUTO: the pump at 40 % at 24 C or below, rising in a straight line to 100 % at 30 C (warm water holds less oxygen:
      the dashboard shows the saturation, 8.3 mg/L at 24 C, 7.4 mg/L at 30 C);
    * above 30 C: TOO WARM - the bar's top segment blinks;
    * FEED: the pump stops for 15 s so the food sinks instead of swirling, then AUTO again;
    * one temperature reading a second (12 bits, 750 ms a conversion, started a second before it is read).
  Its pages:
    /          the dashboard: the controls, the water, the oxygen it can hold, the pump, the events
    /auto  /feed  /full  /off     the modes (/full = 100 %)
    /data      everything as JSON
  Libraries: OneWire and DallasTemperature (the Arduino IDE's Library Manager); the sketch drives the bar and the pump.

TEST STATUS
  Tested in Proteus 8 Professional on Windows 11, the run that made the tutorial's screenshots (the sketch's times):
  - 2 - 8 s: 24.00 C - "AUTO: the pump 40 %": 2.09 V through the L9110S, 1,500 RPM, 0.54 L/min of bubbles at 35 mmHg
    (150 mA); the bar 4 green segments (U2 latched 0x0F, 5.5 mA each); the water holds up to 8.33 mg/L of oxygen.
  - 8 - 10 s: +1 C three times in the DS18B20's pop-up: 25 C - 50 %, 27 C - 70 % (3.83 V, 1.20 L/min at 43 mmHg);
    the bar 7 (0x7F: five green, two yellow), 39.4 mA through U2's VCC; 7.87 mg/L.
  - 14 s: FEED from the phone: the pump 0 %, the bubbles stop (the line holds 28 mmHg);
    29 s: "feeding over: AUTO again", 70 %.
  - 32 - 34 s: +1 C four times: 31 C - 100 % (5.59 V, 1.85 L/min at 51 mmHg, 193 mA); "TOO WARM: above 30 C - the top
    segment blinks": the bar 9 / 10 every half second (U3 latched 0x01 / 0x03), 6.25 mA in each red segment; 7.30 mg/L.
  - 39 s: OFF from the laptop - the pump stops; 42 s: AUTO from the laptop - 100 % again.
  - 45 s: -10 C: 21 C - "the water below 30 C again", the bar 1 segment, the pump 40 %; 8.84 mg/L.
  - 50.6 s of simulation in 1,008 s. The L9110S's pop-up keeps a 5.3 A "peak" from one input pulse at 2.3 ms, while
    the board was starting; after that its current stays below 0.2 A.

INSTALLATION
  1. Close Proteus. Extract the WHOLE zip file, for example to your Desktop.
  2. Copy the files from "Proteus Library Files" into the LIBRARY folder of Proteus, for example
     C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
  3. Copy the files from "Proteus Model Files" into the MODELS folder (next to LIBRARY).
  4. Start Proteus. Press P in the schematic and search for ESP32 DEVKIT V1, SN74HC595TEP, LEDBAR10MIXTEP,
     MINIAIRPUMPTEP, DS18B20PROBEADVTEP or L9110SADVTEP to check that the parts are there.

RUN THE SIMULATION
  1. Open "Proteus Simulation\ESP32-Aquarium-Controller.pdsprj". Keep the HEX and the DLL files beside it.
  2. Press Play. The water is at 24 C: the bar shows 4 segments, the pump runs at 40 %.
  3. In the DS18B20's pop-up (U4) press +1 or +10 to warm the water, -1 or -10 to cool it.
  4. Open the Laptop WiFi Monitor (PC1) or the Mobile WiFi Monitor (MOB1) and press Go: AUTO, FEED, 100 % and OFF.
  Your own sketch: compile it (with OneWire and DallasTemperature), export the compiled binary and set U1's PROGRAM
  property to the new file.

PROPERTIES USED IN THIS PROJECT
  U1 ESP32 DEVKIT V1           PROGRAM=ESP32_Aquarium_Controller.hex, AUTOOPEN=YES (TEP-WiFi, 192.168.1.101)
  U4 DS18B20PROBEADVTEP        TEMPERATURE=24
  U2, U3 SN74HC595TEP          RON=30 (ohm, an output's resistance)
  BAR1 LEDBAR10MIXTEP          (no changes)
  DRV1 L9110SADVTEP            (no changes) on +6V
  M1 MINIAIRPUMPTEP            LOAD=AQUARIUM, DEPTH=30 (cm)
  R1 - R10 220 ohm, R11 4.7 kohm
  PC1, MOB1                    HOMEPAGE=http://192.168.1.101/

TROUBLESHOOTING
  * The bar stays dark: SRCLR low (it clears the shift registers), OE high, or RCLK never pulsed after the bytes.
  * Segments 9 and 10 stay dark: U3's SER (D21) not wired, or its byte not set on SER2 during the 8 clocks.
  * The temperature reads 85 C at the start: a conversion read before it finished - wait 750 ms after the first one.
  * The temperature reads -127 C: no DS18B20 on D4, or the 4.7 k pull-up missing.
  * No bubbles at low power: the pump must beat the water column and the stone - keep at least 40 %.

LICENCES
  * The project, the sketch, the parts (LIB files) and the models (DLL files) are made by The Engineering Projects
    and are free for learning and for your own projects. The models use only standard Windows libraries.
    The C++ source code of the models is not included; the source code is not included for any model.
  * OneWire (Paul Stoffregen) and DallasTemperature (Miles Burton and others) are open-source Arduino libraries,
    installed from the Arduino IDE's Library Manager; they are not part of this zip.
  * Proteus is a product of Labcenter Electronics and is not included. ESP32 is a product of Espressif Systems; the
    DS18B20 of Analog Devices (Maxim); the 74HC595 is made by several companies.
    This project is not made or endorsed by them. It is a teaching project, not a certified life-support device.

VERSION
  V1.0 - the first release of the project.
===============================================================================================================
Advertisement

Development1 release

  1. V1.0IoT Aquarium Controller with ESP32 - Proteus Simulation V1.0this page

    V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.

Installation8 steps

From the download to a working project, in order. The steps follow what the package contains.

You will need

  • Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
  • Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
  • Any archive toolWindows, macOS and Linux extract ZIP files on their own

Steps

  1. 1

    Extract the archive

    Right-click a55701f537394423842dabedce1fcc8c.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (ESP32-Aquarium-Controller-TEP-v1.0) as it is.

  2. 2

    Copy the library files into Proteus

    Move TEPAIRPUMP.LIB, TEPDS18B20.LIB and TEPESP32V1.LIB and 6 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.

  3. 3

    Add the simulation model

    Copy TEPAIRPUMP.DLL, TEPDS18B20.DLL and TEPHC595.DLL and 4 more into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.

  4. 4

    Restart Proteus and place the component

    Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.

  5. 5

    Open the sketch in the Arduino IDE

    Open ESP32_Aquarium_Controller.ino, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.

  6. 6

    Load the HEX file

    In Proteus double-click the microcontroller, set Program File to ESP32_Aquarium_Controller.hex and run the simulation. For real hardware, flash the same file with your programmer.

  7. 7

    Open the example simulation

    Open ESP32-Aquarium-Controller.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.

  8. 8

    Follow the tutorial

    IoT Aquarium Controller with ESP32 - Proteus Simulation explains every connection and setting in order; keep it open beside the files while you build.

How to add a library in Proteus 8

FAQs9 questionsContact TEP

How do I download IoT Aquarium Controller with ESP32 - Proteus Simulation V1.0?

Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.

What is inside the archive?

IoT Aquarium Controller with ESP32 - Proteus Simulation V1.0 comes as a ZIP archive of 27 files (4.6 MB, 10.1 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware. Open the File Structure tab for the full list of 27 files.

What should I do if the download does not start?

Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.

Is this file free?

Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.

How do I check that the file arrived complete?

Compare its SHA-256 with the one on this page, cd0d6e14dc7a64b665d3a470d17c17892869d520709d87b8a73385dffcd92ac9. In PowerShell run Get-FileHash "a55701f537394423842dabedce1fcc8c.zip"; on macOS or Linux run shasum -a 256 "a55701f537394423842dabedce1fcc8c.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.

Do I need WinRAR to open the ZIP file?

No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.

Where do I put the LIB and IDX files?

Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.

Which Proteus version does the library need?

The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.

How do I get the HEX file into the simulation?

Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.

preparing · a55701f537394423842dabedce1fcc8c.zip
Rating
Your download will be ready shortly
Preparing your download…

Members skip the wait. Log in or join TEP.

Last 14 days0 downloads
SHA-256 cd0d6e14dc7a64b665d3a470d17c17892869d520709d87b8a73385dffcd92ac9
DocumentationIoT Aquarium Controller with ESP32 - Proteus Simulation
Need help with this file? Bug report Ask a question Download problemsGet updates
Advertisement

Comments

0

Join the conversation

Start the conversationAsk a question or share how you used this download.