Hello everyone! I hope you all will be absolutely fine and having fun. Today, I am going to provide a detailed discussion on Introduction to Laser Sensor. Laser sensor is basically an electronic device which we often use for the detection of accurate positions as well as small objects. Laser sensors transmit or radiate laser light. This laser light consists of light waves having same wave length. Due to this fact laser light travels in a parallel direction from the source emitting this light. Due to its travel in parallel direction it can be transmitted over long distances. This light is dangerous for the human beings.
We must avoid by looking directly into the light. It causes serious eye damaging effect and even can make anyone blind. As we ...
Hi Friends! I welcome you on board. Thank you for clicking this read. In this post today, I’ll document the Introduction to D13003K.
The D13003K is an NPN silicon transistor mainly employed for switching and amplification purposes. It comes with a power dissipation of around 50W which demonstrates the amount of energy this device releases during the functioning of this device. As this is an NPN transistor as here electrons are the major charge carriers. The collector current is 1.8A which means it can support load under 1.8A. The emitter-base voltage is 9V which means it needs 9V to bias this device and start the transistor action.
I suggest you read this post all the way through as I’ll walk you through the complete Introduction to D13003K covering pinout, datasheet, power ratings, ...
Hello friends, hope you are having fun. In today's post, we will have a look at Serial Communication with 8051 Microcontroller in Proteus ISIS. In the previous post, we have seen a detailed post on LED Blinking Project using 8051 Microcontroller in Proteus ISIS, which was quite a simple tutorial. And I hope if you are new to 8051 Microcontroller then from that post you must have got some idea about C Programming of 8051 Microcontroller.
Now, today we are gonna go a little further and will have a look at Serial Communication with 8051 Microcontroller and we will also design the simulation of this project in Proteus ISIS software. 8051 Microcontroller also supports Serial port similar to Arduino and PIC Microcontroller. And the communication protoco ...
Hello friends, I hope you all are doing great. In today's tutorial, we are gonna have a look at detailed Introduction to TIP31. The TIP31 is a typical NPN transistor which is frequently cast-off for intermediate power submissions. This (BJT) is a three (3) points expedient which works for intensification or swapping submissions. It is designed by linking three units of semiconductors with alternatively dissimilar doping. The central unit which is (base) is thin and the other two external areas (emitter and collector) are greatly doped.
Some transistors can intensify a minor current which will then be dominant sufficient to work a spotlight or other higher current expedients. These diplomacies are also capable to notice an alteration in voltage an ...
Hey Guys! I hope everyone's fine. Today, we are going to have a look at What is MOSFET? We will cover MOSFET Definition, Full Form, Symbol, Working & Applications in detail.
MOSFETs are commonly used in many electronic applications. A number of MOSFETs are added in tiny memory chips or microprocessors that are widely used in cell phones and laptops. It is a voltage-controlled device that is used for amplification and switching purposes. I'll try to touch every area related to MOSFET. Let's get started.
What is MOSFET?
MOSFET is an advanced type of FET, manufactured with controlled oxidation of semiconductor, having 4 Terminals, named:
Drain(D)
Gate(G)
Source(S)
Body(B)
where,
Gate(G) Terminal is practically insul ...
Hello everyone! I hope you will absolutely fine and having fun. Today, I am going to give you a detailed discussion on the topic Introduction to 78M05. I have already shared information about different IC's e.g. Introduction to UA741, MMBD914, LM224, LM386 and LM317. You must have a look at all these tutorials for the better understanding of this article. 78-M05 is basically a three (3) terminal. These terminals include input, output and the common terminal.
78-M05 is commonly available in TO-220 package having different fixed voltages at the output. Its construction process is based on planar epitaxial technology. These regulators are used for the employment of the process of internal limitation of the current. Safe area compensation as well a ...
Hello everyone! I hope you all will be absolutely fine and having fun. Today, I am going to elaborate about the Introduction to LM324. It is an Operational Amplifier (Op-amp) consists of four channels. Its a low cost device having true differential inputs.For single supply applications LM 324 are superior to the other operational amplifiers. LM-324 is capable of operating at the minimum voltage up to 3V and at the high voltage levels up to 32V.
One of the major advantage of LM-324 is that common mode input range includes negative supply which eliminates the need of external biasing. Negative power supply voltage is also included in output voltage range. This device is lead (Pb) free, halogen free and RoHS compliant. It consists of four amplifier ...
Hello readers, I hope you are all doing great. In this tutorial, we are going to discuss the OTA web updater on the ESP32.
We already covered the fundamentals of OTA programming in ESP32, in our previous tutorial where we used the Arduino IDE to upload OTA code into the ESP32 module using the network port.
In the OTA web updater, you need to create a web server page for OTA programming.
[caption id="attachment_166886" align="aligncenter" width="1920"]
ESP32 OTA web updater[/caption]
Fig.1 ESP32 OTA web updater
Over the Air Web Updater
"Over-the-air" refers to the ability to wirelessly download an application, configuration, or firmware to internet-enabled devices, also known as IoT. (OTA). It functions similarly to our computers, laptops, tab ...
Hello readers, I hope you all are doing well. Welcome to the Section 2 (ESP32 Features) of the ESP32 Programming Series. ESP32 is equipped with numerous built-in features and in each chapter of this Section 2, we will explore one of these ESP32 features in detail.
In the previous Section(Section 1: ESP32 IDEs), we installed different software IDEs to program ESP32 boards. Among these IDEs, we are going to use Arduino IDE for programming ESP32. So, I hope all of your tools are configured properly and you are ready to explore the built-in features of ESP32.Today's the 1st Chapter of Section 2, and here we will discuss How to communicate with ESP32 Bluetooth Classic from a smartphone using Arduino IDE.
Here's the video tutorial for ESP32 Bluetooth Classic:
ESP32 Wireless Features ...
Hello friends, I hope you all are doing great. In today's tutorial, I am going to show you How to Interface Arduino with 74HC595 & 74HC165. I have already interfaced these shift registers separately with Arduino. In the first tutorial we have seen Arduino 74HC595 Interfacing in which I have discussed How to increase the output pins of Arduino using 74HC595. After that in second tutorial we have seen Arduino 74HC165 Interfacing where we have increased the input pins of Arduino.
So, now we are gonna interface both of these shift registers with Arduino UNO and will increase both input and output pins of Arduino. I have also given the Proteus simulations for download at the end of this tutorial along with Arduino code. So, lets get started with In ...
