TEP DOWNLOAD CENTER

Project Files of Classroom Noise Meter: ESP32, KY-038 and SHT31 Proteus Simulation

Libraries Code Projects Simulation
tep://download-terminal 4988ecc9cfd34511bac93f350a86861e.zip ZIP archiveV1.0Verified0 downloadsFree
Classroom Noise Meter: ESP32, KY-038 and SHT31 Proteus Simulation: the ESP32, the KY-038 sound sensor, the SHT31, the SH1106 OLED and the green, amber and red noise light
Proteus library · File 1 of 1

Classroom Noise Meter: ESP32, KY-038 and SHT31 Proteus Simulation V1.0

Classroom Noise Meter: ESP32, KY-038 and SHT31 Proteus Simulation V1.0 comes as a ZIP archive of 24 files (4.7 MB, 10.3 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware.

  • LIBProteus library
  • DLLProteus model
  • DSNProteus simulation
  • INOArduino sketch
  • HEXHEX firmware

Description

Classroom-Noise-Meter-ESP32-KY-038-Proteus-Simulation-v1.0.zip: the complete Proteus simulation project (ESP32 DevKit V1, a KY-038 sound sensor, an SHT31, an SH1106 OLED, SMD LEDs and resistors, the Laptop and Mobile WiFi Monitors), the Arduino sketch and its HEX file, every LIB and DLL and a README.

Read Classroom Noise Meter: ESP32, KY-038 and SHT31 Proteus Simulation

File Structure

4988ecc9cfd34511bac93f350a86861e.zip24 files · 5 folders · 10.3 MB unpacked
ESP32-Classroom-Noise-Meter-TEP-v1.0/24 files · 10.3 MB
Arduino Code/1 file · 9.8 KB
ESP32_Noise_Meter/1 file · 9.8 KB
INO ESP32_Noise_Meter.inoArduino sketch 9.8 KB
Proteus Library Files/8 files · 509.3 KB
LIB TEPESP32V1.LIBProteus library 36.6 KB
LIB TEPLAPTOP.LIBProteus library 39.5 KB
LIB TEPMOBILE.LIBProteus library 13.1 KB
LIB TEPOLEDSH1106.LIBProteus library 77.5 KB
LIB TEPSHT31.LIBProteus library 44.4 KB
LIB TEPSMDLED.LIBProteus library 17.7 KB
LIB TEPSMDRES.LIBProteus library 171.9 KB
LIB TEPSOUND.LIBProteus library 108.7 KB
Proteus Model Files/6 files · 4.8 MB
DLL TEPNET.DLLSimulation model 3.0 MB
DLL TEPOLED.DLLSimulation model 342.5 KB
DLL TEPSHT31.DLLSimulation model 537 KB
DLL TEPSMDLED.DLLSimulation model 290.5 KB
DLL TEPSMDRES.DLLSimulation model 305.5 KB
DLL TEPSOUND.DLLSimulation model 410.5 KB
Proteus Simulation/8 files · 4.9 MB
DSN ESP32-Noise-Meter.pdsprjProteus simulation 33.4 KB
HEX ESP32_Noise_Meter.hexCompiled HEX file 105 KB
DLL TEPNET.DLLSimulation model 3.0 MB
DLL TEPOLED.DLLSimulation model 342.5 KB
DLL TEPSHT31.DLLSimulation model 537 KB
DLL TEPSMDLED.DLLSimulation model 290.5 KB
DLL TEPSMDRES.DLLSimulation model 305.5 KB
DLL TEPSOUND.DLLSimulation model 410.5 KB
TXT README.txtText file 10.5 KB

README

README.txt 143 lines
===============================================================================================================
  Classroom Noise Meter: ESP32, KY-038 and SHT31 Proteus Simulation - Project V1.0
  The Engineering Projects - www.TheEngineeringProjects.com
===============================================================================================================

IMPORTANT LINKS
  The project tutorial (circuit, code, simulation results):
    https://www.theengineeringprojects.com/2026/11/classroom-noise-meter-esp32-ky-038-proteus-simulation.html
  The libraries this project is built from (each post has its own full download and tutorial):
    ESP32 DevKit V1 board:
      https://www.theengineeringprojects.com/2026/10/esp32-devkit-v1-library-for-proteus-v2-0.html
    KY-038 sound sensor:
      https://www.theengineeringprojects.com/2026/10/sound-sensor-library-for-proteus-v3-0.html
    SHT31 temperature / humidity sensor:
      https://www.theengineeringprojects.com/2026/09/sht31-proteus-library.html
    SH1106 1.3" OLED display:
      https://www.theengineeringprojects.com/2026/10/oled-sh1106-library-for-proteus-v1-0.html
    SMD LED:
      https://www.theengineeringprojects.com/2026/11/smd-led-library-for-proteus.html
    SMD resistor:
      https://www.theengineeringprojects.com/2026/11/smd-resistor-library-for-proteus.html
    Laptop WiFi Monitor:
      https://www.theengineeringprojects.com/2026/10/laptop-wifi-monitor-library-for-proteus.html
    Mobile WiFi Monitor:
      https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
  Support our free work: https://www.theengineeringprojects.com/donate

FILE STRUCTURE
ESP32-Classroom-Noise-Meter-TEP-v1.0/
|-- Proteus Library Files/
|   |-- TEPESP32V1.LIB                                 36.6 KB   a part of the project -> LIBRARY folder
|   |-- TEPLAPTOP.LIB                                  39.5 KB   a part of the project -> LIBRARY folder
|   |-- TEPMOBILE.LIB                                  13.1 KB   a part of the project -> LIBRARY folder
|   |-- TEPOLEDSH1106.LIB                              77.5 KB   a part of the project -> LIBRARY folder
|   |-- TEPSHT31.LIB                                   44.4 KB   a part of the project -> LIBRARY folder
|   |-- TEPSMDLED.LIB                                  17.7 KB   a part of the project -> LIBRARY folder
|   |-- TEPSMDRES.LIB                                 171.9 KB   a part of the project -> LIBRARY folder
|   |-- TEPSOUND.LIB                                  108.7 KB   a part of the project -> LIBRARY folder
|-- Proteus Model Files/
|   |-- TEPNET.DLL                                     2.97 MB   a model -> MODELS folder
|   |-- TEPOLED.DLL                                   342.5 KB   a model -> MODELS folder
|   |-- TEPSHT31.DLL                                  537.0 KB   a model -> MODELS folder
|   |-- TEPSMDLED.DLL                                 290.5 KB   a model -> MODELS folder
|   |-- TEPSMDRES.DLL                                 305.5 KB   a model -> MODELS folder
|   |-- TEPSOUND.DLL                                  410.5 KB   a model -> MODELS folder
|-- Proteus Simulation/
|   |-- ESP32_Noise_Meter.hex                         105.0 KB   the firmware
|   |-- ESP32-Noise-Meter.pdsprj                       33.4 KB   the project simulation
|   |-- TEPNET.DLL                                     2.97 MB   copy of the model
|   |-- TEPOLED.DLL                                   342.5 KB   copy of the model
|   |-- TEPSHT31.DLL                                  537.0 KB   copy of the model
|   |-- TEPSMDLED.DLL                                 290.5 KB   copy of the model
|   |-- TEPSMDRES.DLL                                 305.5 KB   copy of the model
|   |-- TEPSOUND.DLL                                  410.5 KB   copy of the model
|-- Arduino Code/
|   |-- ESP32_Noise_Meter/ESP32_Noise_Meter.ino         9.8 KB   the sketch (source of the .hex)
|-- README.txt                                        ~10.4 KB   this file
Total: 10.28 MB (unzipped). The C++ source code of the models is not included.

WHAT IS IT?
  A noise and comfort meter for a classroom, a library or an open office: a traffic light that turns amber when
  the class talks and red when it gets too loud, an OLED on the wall and a dashboard on the teacher's laptop.
    * U1 ESP32 DEVKIT V1 runs ESP32_Noise_Meter.hex on TEP-WiFi at 192.168.1.101 (port 80).
    * U2 a KY-038 sound sensor (SOUNDADVTEP, the pop-up panel): A0 (the microphone's amplified signal) to D34,
      D0 (its LM393 comparator) to D35, VCC on a +3.3V supply terminal.
    * U3 an SHT31 temperature / humidity sensor (SHT31ADVTEP, the pop-up panel) and OLED1 an SH1106 1.3" OLED
      (SH1106WHITEADVTEP) on I2C: SDA D21, SCL D22; the SHT31's ADDR to GND (0x44), the OLED at 0x3C.
      The OLED's VDD is on +3.3V; the SHT31's VIN is on the default power rail - its digital model reads VIN as a
      logic level (a real GY-SHT31-D has its own regulator and takes 3.3 V or 5 V).
    * D1 / D2 / D3 the noise light, SMD LEDs green / amber / red (LEDSMDGREENTEP, LEDSMDAMBERTEP, LEDSMDREDTEP) from
      D25 / D26 / D27 through R1 - R3, 220 ohm SMD resistors (RESISTORSMD1206TEP).
    * Laptop WiFi Monitor (PC1) and Mobile WiFi Monitor (MOB1) open http://192.168.1.101/.
  The rules (at the top of the sketch):
    * every 50 ms the ESP32 samples A0 as fast as it can and takes the swing (peak to peak); the swing in dB
      against 1 mV is the level, dB(rel) - relative, because a KY-038 is not calibrated;
    * the meter level follows it like a VU needle: half way up in one window, 2 % of the way down per window;
    * below 20 dB(rel) QUIET (green), 20 - 40 TALKING (amber), 40 and up TOO LOUD (red); too loud for 5 s in a row
      is a WARNING;
    * D0 on an interrupt: a burst of D0 pulses shorter than 60 ms is a bang (a clap, a door slamming); a long
      sound (an alarm, shouting) trips D0 for longer and is not counted as a bang;
    * the SHT31 every 2 s: comfortable at 20 - 26 C and 30 - 60 % RH, else too warm / too cold / too humid / too dry.
  The pages:
    /          the dashboard: the light, the level and the peak, loud time, bangs, warnings, the room, the events
    /reset     clears the counters and the peak                    /data      JSON
  Libraries: Adafruit SHT31, Adafruit SH110X, Adafruit GFX and Adafruit BusIO (Library Manager); WiFi, WebServer and
  Wire are part of the ESP32 core.

TEST STATUS
  Tested in Proteus 8 Professional on Windows 11, the run that made the tutorial's screenshots (the sketch's times):
  - The empty room: 15 dB(rel) (the microphone's own noise, a 5.6 mV swing), QUIET, green; 2.5 s "the room: 25.0 C,
    50 % - comfortable" (the SHT31's pop-up: the sketch read 24.99 C, 50.00 %, dew point 13.8 C).
  - Group work (Talking, 68 dB at 10 cm): 13.2 s TALKING (21 dB), the needle at 23 - 24 dB(rel), amber.
  - The class shouting (Talking at 90 dB): 22.1 s TOO LOUD (42 dB), the needle at 43 - 44, red; 27.2 s "WARNING: too
    loud for 5 s". Each syllable trips D0 for about 114 ms (18 pulses): no bangs.
  - Quiet: the needle falls slowly - TALKING (37 dB) at 34.6 s, QUIET (17 dB) at 41.9 s. One clap, then a double clap:
    three bangs, D0 tripped for 17 ms each (the pop-up: 9 pulses in 18.1 ms); each clap lifted the needle to amber
    for a few seconds; QUIET again at 53.1 s.
  - The school bell (Alarm, 90 dB): 58.4 s TOO LOUD (44 dB), the needle at 45; 63.4 s the second warning; D0 tripped
    for 244.5 ms per beep (216 pulses): 0 bangs.
  - A stuffy room (the SHT31 at 71 %): 68.6 s "the room: 25.0 C, 71 % - too humid"; QUIET again at 75.9 s.
  - The dashboard before RESET: loud 28 % of the time, 3 bangs, 2 warnings, peak 53 dB(rel); 84.1 s RESET.
  - 86 s of simulation in about 7 minutes.

INSTALLATION
  1. Close Proteus. Extract the WHOLE zip file, for example to your Desktop.
  2. Copy the files from "Proteus Library Files" into the LIBRARY folder of Proteus, for example
     C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
  3. Copy the files from "Proteus Model Files" into the MODELS folder (next to LIBRARY).
  4. Start Proteus. Press P in the schematic and search for ESP32 DEVKIT V1, SOUNDADVTEP or SHT31ADVTEP to check
     that the parts are there.

RUN THE SIMULATION
  1. Open "Proteus Simulation\ESP32-Noise-Meter.pdsprj". Keep the HEX file and the DLL files beside it.
  2. Press Play. The empty room reads about 15 dB(rel): the green light.
  3. On the sound sensor's pop-up (U2) pick a source: Talking (amber), then drag the Level up to 90 dB (red, and
     a warning after 5 s); Quiet, then Clap and Double clap (bangs); Alarm (red, no bangs).
  4. On the SHT31's pop-up (U3) move the humidity or the temperature, or pick a preset.
  5. Open the Laptop WiFi Monitor (PC1) or the Mobile WiFi Monitor (MOB1) and press Go: Refresh, RESET.
  Your own sketch: compile it, export the compiled binary and set U1's PROGRAM to the new file.

PROPERTIES USED IN THIS PROJECT
  U1 ESP32 DEVKIT V1           PROGRAM=ESP32_Noise_Meter.hex, AUTOOPEN=YES (TEP-WiFi, 192.168.1.101)
  U2 SOUNDADVTEP               the quiet room at 10 cm, the pot at 530 (the pop-up changes the scene)
  U3 SHT31ADVTEP               25 C, 50 % (the pop-up);  OLED1 SH1106WHITEADVTEP  address 0x3C
  D1 - D3 SMD LEDs; R1 - R3 220 ohm
  PC1, MOB1                    HOMEPAGE=http://192.168.1.101/

TROUBLESHOOTING
  * "SHT31 not found at 0x44": SDA / SCL are not on D21 / D22, ADDR is not on GND, or VIN has no supply.
  * The OLED stays dark: VDD and GND, SDA D21 / SCL D22; the address must be 0x3C.
  * The light never leaves green: A0 must be on D34 (an ADC1 pin - ADC2 pins do not work while Wi-Fi is on).
  * Claps are not counted: D0 must be on D35, and the sensitivity pot must leave the quiet A0 above VCC/2.

LICENCES
  * The project, the sketch, the parts (LIB files) and the models (DLL files) are made by The Engineering
    Projects and are free for learning and for your own projects. The models use only standard Windows libraries.
    The C++ source code of the models is not included; the source code is not included for any model.
  * Proteus is a product of Labcenter Electronics and is not included. ESP32 is a product of Espressif Systems,
    the SHT31 a sensor of Sensirion. This project is not made or endorsed by them.

VERSION
  V1.0 - the first release of the project.
===============================================================================================================
Advertisement

Development1 release

  1. V1.0Classroom Noise Meter: ESP32, KY-038 and SHT31 Proteus Simulation V1.0this page

    V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.

Installation8 steps

From the download to a working project, in order. The steps follow what the package contains.

You will need

  • Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
  • Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
  • Any archive toolWindows, macOS and Linux extract ZIP files on their own

Steps

  1. 1

    Extract the archive

    Right-click 4988ecc9cfd34511bac93f350a86861e.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (ESP32-Classroom-Noise-Meter-TEP-v1.0) as it is.

  2. 2

    Copy the library files into Proteus

    Move TEPESP32V1.LIB, TEPLAPTOP.LIB and TEPMOBILE.LIB and 5 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.

  3. 3

    Add the simulation model

    Copy TEPNET.DLL, TEPOLED.DLL and TEPSHT31.DLL and 3 more into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.

  4. 4

    Restart Proteus and place the component

    Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.

  5. 5

    Open the sketch in the Arduino IDE

    Open ESP32_Noise_Meter.ino, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.

  6. 6

    Load the HEX file

    In Proteus double-click the microcontroller, set Program File to ESP32_Noise_Meter.hex and run the simulation. For real hardware, flash the same file with your programmer.

  7. 7

    Open the example simulation

    Open ESP32-Noise-Meter.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.

  8. 8

    Follow the tutorial

    Classroom Noise Meter: ESP32, KY-038 and SHT31 Proteus Simulation explains every connection and setting in order; keep it open beside the files while you build.

How to add a library in Proteus 8

FAQs9 questionsContact TEP

How do I download Classroom Noise Meter: ESP32, KY-038 and SHT31 Proteus Simulation V1.0?

Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.

What is inside the archive?

Classroom Noise Meter: ESP32, KY-038 and SHT31 Proteus Simulation V1.0 comes as a ZIP archive of 24 files (4.7 MB, 10.3 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware. Open the File Structure tab for the full list of 24 files.

What should I do if the download does not start?

Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.

Is this file free?

Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.

How do I check that the file arrived complete?

Compare its SHA-256 with the one on this page, 4d0b74906f29159fe534eb9032fe06e34bcd2797e13a2345188287053591f6c5. In PowerShell run Get-FileHash "4988ecc9cfd34511bac93f350a86861e.zip"; on macOS or Linux run shasum -a 256 "4988ecc9cfd34511bac93f350a86861e.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.

Do I need WinRAR to open the ZIP file?

No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.

Where do I put the LIB and IDX files?

Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.

Which Proteus version does the library need?

The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.

How do I get the HEX file into the simulation?

Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.

preparing · 4988ecc9cfd34511bac93f350a86861e.zip
Rating
Your download will be ready shortly
Preparing your download…

Members skip the wait. Log in or join TEP.

Last 14 days0 downloads
SHA-256 4d0b74906f29159fe534eb9032fe06e34bcd2797e13a2345188287053591f6c5
DocumentationClassroom Noise Meter: ESP32, KY-038 and SHT31 Proteus Simulation
Need help with this file? Bug report Ask a question Download problemsGet updates
Advertisement

Comments

0

Join the conversation

Start the conversationAsk a question or share how you used this download.