TEP DOWNLOAD CENTER

Project Files of ESP32 Piezo Energy Harvesting Node (Proteus Simulation)

Libraries Code Projects Simulation
tep://download-terminal 8c959c9e67cd4658b486a37a46946795.zip ZIP archiveV1.0Verified0 downloadsFree
ESP32 Piezo Energy Harvesting Node (Proteus Simulation): the ESP32, the piezo disc on a vibrating machine, the bridge rectifier, the store capacitor and the burst load
Proteus library · File 1 of 1

ESP32 Piezo Energy Harvesting Node in Proteus Simulation V1.0

ESP32 Piezo Energy Harvesting Node in Proteus Simulation V1.0 comes as a ZIP archive of 27 files (4.6 MB, 9.9 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware.

  • LIBProteus library
  • DLLProteus model
  • DSNProteus simulation
  • INOArduino sketch
  • HEXHEX firmware

Description

ESP32-Piezo-Energy-Harvesting-Node-Proteus-Simulation-v1.0.zip: the complete Proteus simulation project (ESP32 DevKit V1, the piezo energy harvester, a DB107 bridge rectifier, a 220 uF electrolytic, an IRLZ44N, a red LED, resistors, the Laptop and Mobile WiFi Monitors), the Arduino sketch and its HEX file, every LIB and DLL and a README.

Read ESP32 Piezo Energy Harvesting Node (Proteus Simulation)

File Structure

8c959c9e67cd4658b486a37a46946795.zip27 files · 5 folders · 9.9 MB unpacked
ESP32-Piezo-Harvester-TEP-v1.0/27 files · 9.9 MB
Arduino Code/1 file · 6.9 KB
ESP32_Piezo_Harvester/1 file · 6.9 KB
INO ESP32_Piezo_Harvester.inoArduino sketch 6.9 KB
Proteus Library Files/9 files · 467.9 KB
LIB TEPBRIDGE.LIBProteus library 10.8 KB
LIB TEPELECTRO.LIBProteus library 10.1 KB
LIB TEPESP32V1.LIBProteus library 36.6 KB
LIB TEPLAPTOP.LIBProteus library 39.5 KB
LIB TEPLED5MM.LIBProteus library 21.8 KB
LIB TEPMOBILE.LIBProteus library 13.1 KB
LIB TEPNMOS.LIBProteus library 17.9 KB
LIB TEPPIEZO.LIBProteus library 11.2 KB
LIB TEPRESISTOR.LIBProteus library 306.9 KB
Proteus Model Files/7 files · 4.6 MB
DLL TEPBRIDGE.DLLSimulation model 284 KB
DLL TEPELECTRO.DLLSimulation model 294.5 KB
DLL TEPLED5MM.DLLSimulation model 289.5 KB
DLL TEPNET.DLLSimulation model 2.9 MB
DLL TEPNMOS.DLLSimulation model 295 KB
DLL TEPPIEZO.DLLSimulation model 314 KB
DLL TEPRESISTOR.DLLSimulation model 311 KB
Proteus Simulation/9 files · 4.7 MB
DSN ESP32-Piezo-Harvester.pdsprjProteus simulation 31.6 KB
HEX ESP32_Piezo_Harvester.hexCompiled HEX file 68.2 KB
DLL TEPBRIDGE.DLLSimulation model 284 KB
DLL TEPELECTRO.DLLSimulation model 294.5 KB
DLL TEPLED5MM.DLLSimulation model 289.5 KB
DLL TEPNET.DLLSimulation model 2.9 MB
DLL TEPNMOS.DLLSimulation model 295 KB
DLL TEPPIEZO.DLLSimulation model 314 KB
DLL TEPRESISTOR.DLLSimulation model 311 KB
TXT README.txtText file 9.4 KB

README

README.txt 133 lines
===============================================================================================================
  ESP32 Piezo Energy Harvesting Node (Proteus Simulation) - Project V1.0
  The Engineering Projects - www.TheEngineeringProjects.com
===============================================================================================================

IMPORTANT LINKS
  The project tutorial (circuit, code, simulation results):
    https://www.theengineeringprojects.com/2026/11/esp32-piezo-energy-harvesting-node-proteus-simulation.html
  The libraries this project is built from (each post has its own full download and tutorial):
    ESP32 DevKit V1 board:
      https://www.theengineeringprojects.com/2026/10/esp32-devkit-v1-library-for-proteus-v2-0.html
    Piezo energy harvester:
      https://www.theengineeringprojects.com/2026/11/piezoelectric-energy-harvester-library-for-proteus.html
    Bridge rectifier:
      https://www.theengineeringprojects.com/2026/11/bridge-rectifier-library-for-proteus.html
    Electrolytic capacitor:
      https://www.theengineeringprojects.com/2026/11/electrolytic-capacitor-library-for-proteus.html
    N-MOSFET (IRLZ44N):
      https://www.theengineeringprojects.com/2026/11/n-mosfet-library-for-proteus.html
    5mm LED:
      https://www.theengineeringprojects.com/2026/11/5mm-led-library-for-proteus.html
    Resistor:
      https://www.theengineeringprojects.com/2026/11/resistor-library-for-proteus.html
    Laptop WiFi Monitor:
      https://www.theengineeringprojects.com/2026/10/laptop-wifi-monitor-library-for-proteus.html
    Mobile WiFi Monitor:
      https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
  Support our free work: https://www.theengineeringprojects.com/donate

FILE STRUCTURE
ESP32-Piezo-Harvester-TEP-v1.0/
|-- Proteus Library Files/
|   |-- TEPBRIDGE.LIB                                  10.8 KB   a part of the project -> LIBRARY folder
|   |-- TEPELECTRO.LIB                                 10.1 KB   a part of the project -> LIBRARY folder
|   |-- TEPESP32V1.LIB                                 36.6 KB   a part of the project -> LIBRARY folder
|   |-- TEPLAPTOP.LIB                                  39.5 KB   a part of the project -> LIBRARY folder
|   |-- TEPLED5MM.LIB                                  21.8 KB   a part of the project -> LIBRARY folder
|   |-- TEPMOBILE.LIB                                  13.1 KB   a part of the project -> LIBRARY folder
|   |-- TEPNMOS.LIB                                    17.9 KB   a part of the project -> LIBRARY folder
|   |-- TEPPIEZO.LIB                                   11.2 KB   a part of the project -> LIBRARY folder
|   |-- TEPRESISTOR.LIB                               306.9 KB   a part of the project -> LIBRARY folder
|-- Proteus Model Files/
|   |-- TEPBRIDGE.DLL                                 284.0 KB   a model -> MODELS folder
|   |-- TEPELECTRO.DLL                                294.5 KB   a model -> MODELS folder
|   |-- TEPLED5MM.DLL                                 289.5 KB   a model -> MODELS folder
|   |-- TEPNET.DLL                                     2.90 MB   a model -> MODELS folder
|   |-- TEPNMOS.DLL                                   295.0 KB   a model -> MODELS folder
|   |-- TEPPIEZO.DLL                                  314.0 KB   a model -> MODELS folder
|   |-- TEPRESISTOR.DLL                               311.0 KB   a model -> MODELS folder
|-- Proteus Simulation/
|   |-- ESP32_Piezo_Harvester.hex                      68.2 KB   the firmware
|   |-- ESP32-Piezo-Harvester.pdsprj                   31.6 KB   the project simulation
|   |-- TEPBRIDGE.DLL                                 284.0 KB   copy of the model
|   |-- TEPELECTRO.DLL                                294.5 KB   copy of the model
|   |-- TEPLED5MM.DLL                                 289.5 KB   copy of the model
|   |-- TEPNET.DLL                                     2.90 MB   copy of the model
|   |-- TEPNMOS.DLL                                   295.0 KB   copy of the model
|   |-- TEPPIEZO.DLL                                  314.0 KB   copy of the model
|   |-- TEPRESISTOR.DLL                               311.0 KB   copy of the model
|-- Arduino Code/
|   |-- ESP32_Piezo_Harvester/ESP32_Piezo_Harvester.ino    6.9 KB   the sketch (source of the .hex)
|-- README.txt                                         ~9.1 KB   this file
Total: 9.86 MB (unzipped). The C++ source code of the models is not included.

WHAT IS IT?
  An energy-harvesting test bench you can run in Proteus: a piezo disc on a vibrating machine fills a capacitor through
  a bridge rectifier, and a tiny "sensor node" wakes only when the capacitor holds enough energy for one reading and
  one radio packet - the way battery-free sensors work. An ESP32 measures it all and serves a web dashboard.
    * PZ1 a 27 mm piezo disc (PIEZODISC27TEP, 40 nC a newton, 20 nF): MODE VIBRATE, FORCE 20 N, RATE 50 Hz.
    * BR1 a DB107 bridge rectifier (BRIDGEDB107TEP): AC1 / AC2 from the disc, P = the store, N = GND.
    * C1 a 220 uF 16 V electrolytic (CAPELECTROTEP): the store; R1 / R2 1 Mohm / 1 Mohm give half of it to D34.
    * The node's load: R5 220 ohm and D1 a red LED (LED5MMREDTEP) from the store, switched on its low side by Q1
      (IRLZ44N, IRLZ44NTEP; gate D25 through R3 100 ohm, R4 10 kohm to GND).
    * ESP32 DEVKIT V1 (U1) runs ESP32_Piezo_Harvester.hex on TEP-WiFi at 192.168.1.101 (port 80).
    * Laptop WiFi Monitor (PC1) and Mobile WiFi Monitor (MOB1) open http://192.168.1.101/.
  The rules (at the top of the sketch):
    * the store read 50 times a second (8 readings averaged);
    * at 3.6 V the node wakes for a BURST until the store is down to 2.4 V: 1/2 C (3.6^2 - 2.4^2) = 0.79 mJ;
    * between bursts the harvested power from how fast the store rises: P = C x V x dV/dt (smoothed).
  Its pages:
    /          the dashboard: the state, the store, the harvest, the bursts, the events
    /burst     one burst now (if the store holds 2.4 V)      /reset     the counters at zero      /data      JSON
  Libraries: WiFi and WebServer - part of the ESP32 core.

TEST STATUS
  Tested in Proteus 8 Professional on Windows 11, the run that made the tutorial's screenshots (the sketch's times):
  - The machine at 20 N, 50 Hz (800 nC each way, 100 times a second): the store rises about 640 mV/s, 0.36 - 0.47 mW
    harvested; the bridge passes about 147 uA and drops 1.6 - 2.1 V; 3.2 s "BURST 1 (the store is full): the node
    wakes at 3.60 V", "burst 1 done: 3.60 -> 2.28 V in 60 ms, 0.86 mJ"; then a burst every 2.1 s.
  - 40 N: twice the charge each way; the store rises 1.36 V/s, 0.95 mW; a burst every 1.0 s.
  - Footsteps (Walk, 2 a second): the harvest falls to about 9 uW, no more bursts; 25.4 s BURST from the phone: "the
    node wakes at 2.88 V", 2.88 -> 2.22 V in 39 ms, 0.37 mJ. With no harvest the divider alone drains 1.4 uA.
  - Back to the machine at 20 N: a burst at 30.3 s; 31.8 s RESET from the laptop: the counters at zero; bursts every
    2.1 s again.
  - 37.4 s of simulation in 239 s.

INSTALLATION
  1. Close Proteus. Extract the WHOLE zip file, for example to your Desktop.
  2. Copy the files from "Proteus Library Files" into the LIBRARY folder of Proteus, for example
     C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
  3. Copy the files from "Proteus Model Files" into the MODELS folder (next to LIBRARY).
  4. Start Proteus. Press P in the schematic and search for ESP32 DEVKIT V1, PIEZODISC27TEP or BRIDGEDB107TEP to
     check that the parts are there.

RUN THE SIMULATION
  1. Open "Proteus Simulation\ESP32-Piezo-Harvester.pdsprj". Keep the HEX and the DLL files beside it.
  2. Press Play. The store fills from the vibrating disc; at 3.6 V the LED flashes for a burst.
  3. Click the piezo disc for its pop-up and change what presses it (footsteps, a machine) or the force.
  4. Open the Laptop WiFi Monitor (PC1) or the Mobile WiFi Monitor (MOB1) and press Go: BURST and RESET.
  Your own sketch: compile it, export the compiled binary and set U1's PROGRAM property to the new file.

PROPERTIES USED IN THIS PROJECT
  U1 ESP32 DEVKIT V1           PROGRAM=ESP32_Piezo_Harvester.hex, AUTOOPEN=YES (TEP-WiFi, 192.168.1.101)
  PZ1 PIEZODISC27TEP           MODE=VIBRATE, FORCE=20, RATE=50
  BR1 BRIDGEDB107TEP           (a DB107);  C1 CAPELECTROTEP  220u, 16 V, ESR 0.5 ohm
  Q1 IRLZ44NTEP;  D1 LED5MMREDTEP;  R1, R2 1 Mohm;  R3 100 ohm;  R4 10 kohm;  R5 220 ohm
  PC1, MOB1                    HOMEPAGE=http://192.168.1.101/

TROUBLESHOOTING
  * The store never fills: the disc is not pressed (its pop-up), or the bridge's AC pins are not on the disc.
  * The bursts never stop: Q1 stays on - check D25, R3 and R4.
  * The store reads double or half: the divider is 1 M / 1 M (DIVIDER = 2.0 in the sketch).

LICENCES
  * The project, the sketch, the parts (LIB files) and the models (DLL files) are made by The Engineering Projects
    and are free for learning and for your own projects. The models use only standard Windows libraries.
    The C++ source code of the models is not included; the source code is not included for any model.
  * Proteus is a product of Labcenter Electronics and is not included. ESP32 is a product of Espressif Systems.
    This project is not made or endorsed by them.

VERSION
  V1.0 - the first release of the project.
===============================================================================================================
Advertisement

Development1 release

  1. V1.0ESP32 Piezo Energy Harvesting Node in Proteus Simulation V1.0this page

    V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.

Installation8 steps

From the download to a working project, in order. The steps follow what the package contains.

You will need

  • Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
  • Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
  • Any archive toolWindows, macOS and Linux extract ZIP files on their own

Steps

  1. 1

    Extract the archive

    Right-click 8c959c9e67cd4658b486a37a46946795.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (ESP32-Piezo-Harvester-TEP-v1.0) as it is.

  2. 2

    Copy the library files into Proteus

    Move TEPBRIDGE.LIB, TEPELECTRO.LIB and TEPESP32V1.LIB and 6 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.

  3. 3

    Add the simulation model

    Copy TEPBRIDGE.DLL, TEPELECTRO.DLL and TEPLED5MM.DLL and 4 more into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.

  4. 4

    Restart Proteus and place the component

    Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.

  5. 5

    Open the sketch in the Arduino IDE

    Open ESP32_Piezo_Harvester.ino, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.

  6. 6

    Load the HEX file

    In Proteus double-click the microcontroller, set Program File to ESP32_Piezo_Harvester.hex and run the simulation. For real hardware, flash the same file with your programmer.

  7. 7

    Open the example simulation

    Open ESP32-Piezo-Harvester.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.

  8. 8

    Follow the tutorial

    ESP32 Piezo Energy Harvesting Node (Proteus Simulation) explains every connection and setting in order; keep it open beside the files while you build.

How to add a library in Proteus 8

FAQs9 questionsContact TEP

How do I download ESP32 Piezo Energy Harvesting Node in Proteus Simulation V1.0?

Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.

What is inside the archive?

ESP32 Piezo Energy Harvesting Node in Proteus Simulation V1.0 comes as a ZIP archive of 27 files (4.6 MB, 9.9 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware. Open the File Structure tab for the full list of 27 files.

What should I do if the download does not start?

Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.

Is this file free?

Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.

How do I check that the file arrived complete?

Compare its SHA-256 with the one on this page, 9c4b27b85821e433b49515403cb6b85e04f2e47885ed711833a2cf337781ac3d. In PowerShell run Get-FileHash "8c959c9e67cd4658b486a37a46946795.zip"; on macOS or Linux run shasum -a 256 "8c959c9e67cd4658b486a37a46946795.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.

Do I need WinRAR to open the ZIP file?

No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.

Where do I put the LIB and IDX files?

Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.

Which Proteus version does the library need?

The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.

How do I get the HEX file into the simulation?

Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.

preparing · 8c959c9e67cd4658b486a37a46946795.zip
Rating
Your download will be ready shortly
Preparing your download…

Members skip the wait. Log in or join TEP.

Last 14 days0 downloads
SHA-256 9c4b27b85821e433b49515403cb6b85e04f2e47885ed711833a2cf337781ac3d
DocumentationESP32 Piezo Energy Harvesting Node (Proteus Simulation)
Need help with this file? Bug report Ask a question Download problemsGet updates
Advertisement

Comments

0

Join the conversation

Start the conversationAsk a question or share how you used this download.