Tutorial: Proteus Libraries - Page 5 of 56

560 articles found.

MT3608 DC-DC Boost Converter Module Library for Proteus Simulation

MT3608 DC-DC Boost Converter Module Library for Proteus Simulation: the module makes 12 V from one 18650 cell beside an Arduino UNO V4.0

Hello friends, I hope you all are doing great. Today, I am going to share the new MT3608 DC-DC Boost Converter Module Library for Proteus Simulation , one more library of our renewable energy series. If you have searched for a Proteus simulation of the small blue step-up module that makes 5 V, 9 V or 12 V out of a single Li-ion cell, this library brings it into Proteus: set the trimmer's voltage, connect a source and a load, and watch what the higher voltage costs. Figure: The simulation at work: 12 V from one Li-ion cell while the cell drains. Updates MT3608 DC-DC Boost Converter Module Library for Proteus Simulation Latest version: V1.0 (November 2026, this tutorial) Other power libraries: LiPo Battery · Single Cell Battery · CR2032 Coin Cell · Solar Panel · MC34063 Buck · MC34064 Boost ...

Proteus Simulation of an ESP32 Ethernet Wind Monitor (WT32-ETH01)

Proteus Simulation of an ESP32 Ethernet Wind Monitor (WT32-ETH01): the WT32-ETH01, the cup anemometer, the wind vane and the WARN and STOP LEDs

Hello friends, I hope you all are doing great. Today, I am going to share the Proteus Simulation of an ESP32 Ethernet Wind Monitor (WT32-ETH01) , the forty-first project of our IoT Projects series. If you have searched for a Proteus simulation of an ESP32 on wired Ethernet, or of a wind speed and direction sensor read by an ESP32, here is a complete one. A WT32-ETH01, an ESP32 board with an Ethernet port of its own, reads a cup anemometer and a wind vane, works out the gusts and the mean wind the way weather services do, raises a WARN and a latched STOP alarm when the wind gets dangerous, and serves a live dashboard over a network cable to a laptop and a phone. Wind is the weather that stops work. Tower cranes, lifting platforms, awnings, solar trackers, drones and outdoor events all have ...

Solar Irradiance Sensor (Pyranometer) Library for Proteus Simulation

Solar Irradiance Sensor (Pyranometer) Library for Proteus Simulation: an Arduino UNO V4.0 with the irradiance sensor at noon

Hello friends, I hope you all are doing great. Today, I am going to share the new Solar Irradiance Sensor (Pyranometer) Library for Proteus Simulation , one more library of our renewable energy series. If you have searched for a Proteus simulation of a pyranometer, the sensor that tells how much sunlight falls on a place, this library brings one into Proteus: a small sensor whose voltage follows the sun through a whole day, with clear skies, passing clouds and overcast weather. Figure: The library at work: the sunlight of a whole day with passing clouds, measured in W/m2. Updates Solar Irradiance Sensor (Pyranometer) Library for Proteus Simulation Latest version: V1.0 (November 2026, this tutorial) Other power libraries: LiPo Battery · Single Cell Battery · CR2032 Coin Cell · Solar Panel · ...

Wind Vane Direction Sensor Library for Proteus Simulation

Wind Vane Direction Sensor Library for Proteus Simulation: an Arduino UNO V4.0 with the wind vane and its pull-up resistor

Hello friends, I hope you all are doing great. Today, I am going to share the new Wind Vane Direction Sensor Library for Proteus Simulation , one more library of our renewable energy series. If you have searched for a Proteus simulation of the wind vane of a weather station, the sensor that tells an Arduino where the wind comes from, this library brings it into Proteus with its eight reed switches and its sixteen positions, and with a vane that swings like a real one. Figure: The library at work: the wind veers round the compass, and the vane follows it from position to position. Updates Wind Vane Direction Sensor Library for Proteus Simulation Latest version: V1.0 (November 2026, this tutorial) Other power libraries: LiPo Battery · Single Cell Battery · CR2032 Coin Cell · Solar Panel · MC ...

EMG Muscle-Controlled Gripper on Raspberry Pi 5 in Proteus Simulation

EMG Muscle-Controlled Gripper on Raspberry Pi 5 in Proteus Simulation: the Raspberry Pi 5, the EMG sensor, the ADS1115 and the DS3218 gripper servo

Hello friends, I hope you all are doing great. Today, I am going to share the EMG Muscle-Controlled Gripper on Raspberry Pi 5 in Proteus Simulation , the fortieth project of our IoT Projects series. If you have searched for a Proteus simulation of a Raspberry Pi with an EMG muscle sensor, here is a complete one. A Raspberry Pi 5 reads the electrical activity of a forearm muscle through an EMG sensor and an ADS1115, and closes a DS3218 servo gripper in proportion to how hard the muscle contracts, the same idea that drives a myoelectric prosthetic hand. It measures the muscle at rest, calibrates a full contraction, can lock the grip so the muscle can relax while the hand holds on, and serves a live web dashboard on a laptop or a phone. Every time a muscle contracts, thousands of its fibres f ...

Dual-Axis Solar Tracker Library for Proteus Simulation

Dual-Axis Solar Tracker Library for Proteus Simulation: an Arduino UNO V4.0 with the solar tracker, its panel turned to the sun

Hello friends, I hope you all are doing great. Today, I am going to share the new Dual-Axis Solar Tracker Library for Proteus Simulation , the last library of our renewable energy series. If you have searched for a Proteus simulation of a solar tracker with two servos and four LDRs, the classic Arduino project, this library gives you the whole mechanism as one small part: the sun moves through the sky, the LDRs see it, and the panel turns on your sheet as your code drives the servos. Figure: The library at work: the sun crosses the sky from sunrise to sunset, and the panel follows it. Updates Dual-Axis Solar Tracker Library for Proteus Simulation Latest version: V1.0 (November 2026, this tutorial) Other power libraries: LiPo Battery · Single Cell Battery · CR2032 Coin Cell · Solar Panel · ...

ESP32 RS485 Modbus Power Monitor with PZEM-017 (Proteus Simulation)

ESP32 RS485 Modbus Power Monitor with PZEM-017 (Proteus Simulation): the ESP32, the MAX485, two PZEM-017 meters, the bulbs and the MOSFET

Hello friends, I hope you all are doing great. Today, I am going to share the ESP32 RS485 Modbus Power Monitor with PZEM-017 (Proteus Simulation) , the thirty-ninth project of our IoT Projects series. If you have searched for a Proteus simulation of an ESP32 talking Modbus RTU over RS485, here is a complete one. An ESP32 DevKit V1 is the Modbus master of an RS485 bus with two PZEM-017 DC energy meters on the same pair of wires, one on each circuit of a 12 V supply: a fridge and the lights. It reads the voltage, current, power and energy of both circuits every second, trips the lights circuit like an electronic circuit breaker when it is overloaded, and serves a live web dashboard on a laptop or a phone. Camper vans, boats, workshops and solar sheds all live on 12 V, and the questions are a ...

PZEM-017 DC Energy Meter Library for Proteus Simulation

PZEM-017 DC Energy Meter Library for Proteus Simulation: an Arduino UNO V4.0, a MAX485 module, the PZEM-017, a shunt, a load and a lead-acid battery

Hello friends, I hope you all are doing great. Today, I am going to share the new PZEM-017 DC Energy Meter Library for Proteus Simulation , the next library of our renewable energy series. If you have searched for a Proteus simulation of the PZEM-017, the small DC energy meter that solar and battery projects read over RS485, this library brings it into Proteus with its real Modbus registers, so that the same Arduino code runs on the simulation and on the real module. Figure: The library at work: the meter answers the Arduino's Modbus requests while the battery runs down to the low voltage alarm. Updates PZEM-017 DC Energy Meter Library for Proteus Simulation Latest version: V1.0 (November 2026, this tutorial) Other power libraries: LiPo Battery · Single Cell Battery · CR2032 Coin Cell · So ...

Focus Stacking Rail on Raspberry Pi 5: Proteus Simulation Project

Focus Stacking Rail on Raspberry Pi 5: Proteus Simulation Project: the Raspberry Pi 5, the TMC2209, the NEMA 17 stage and the PC817 camera trigger

Hello friends, I hope you all are doing great. Today, I am going to share the Focus Stacking Rail on Raspberry Pi 5: Proteus Simulation Project , the thirty-eighth project of our IoT Projects series. If you have searched for a Proteus simulation of a Raspberry Pi stepper motor project for macro photography, here is a complete one. A Raspberry Pi 5 drives a TMC2209 stepper driver and a NEMA 17 linear stage that carries a camera in steps of a few microns, finds its zero on an end switch, and takes a photo at every step through two PC817 optocouplers wired like a camera's remote cable. A live web dashboard, on a laptop or a phone, sets the near and far ends and the step, and starts or stops the stack. Anyone who has photographed a fly's eye or the pins of a chip knows the problem: up close, o ...

ESP32 4-20 mA Gas Detector with an MQ-4 Sensor - Proteus Simulation

ESP32 4-20 mA Gas Detector with an MQ-4 Sensor - Proteus Simulation: the ESP32, the MQ-4, the MCP4725, the LM358, the 2N7000 and the panel meter

Hello friends, I hope you all are doing great. Today, I am going to share the ESP32 4-20 mA Gas Detector with an MQ-4 Sensor - Proteus Simulation , the thirty-seventh project of our IoT Projects series. If you have searched for a Proteus simulation of an ESP32 with a 4-20 mA current loop output, here is a complete one. An ESP32 DevKit V1 reads an MQ-4 methane sensor and sends the gas reading the way industry does, as a current between 4 and 20 milliamperes: an MCP4725 DAC, an LM358 op-amp and a 2N7000 MOSFET turn the reading into the loop current, the ESP32 reads that current back to catch a cut cable, an analog panel meter shows it in the "control room", and a live web dashboard on a laptop or a phone shows the gas in ppm and in percent of the lower explosive limit. Walk into any factory, ...