Tutorial: Proteus Libraries - Page 7 of 56

560 articles found.

IoT Digital Compass with Raspberry Pi 5 - Proteus Simulation

IoT Digital Compass with Raspberry Pi 5 - Proteus Simulation: the Raspberry Pi 5, the GY-271 magnetometer and the 2.4-inch TFT with the compass card

Hello friends, I hope you all are doing great. Today, I am going to share the IoT Digital Compass with Raspberry Pi 5 - Proteus Simulation , the thirtieth project of our IoT Projects series. If you have searched for a Proteus simulation of a Raspberry Pi compass with a GY-271 magnetometer and a TFT display, here is a complete one. A Raspberry Pi 5 reads the Earth's magnetic field from a QMC5883L on a GY-271 module, works out the heading, draws a turning compass card on a 2.4-inch ILI9341 TFT, calibrates out a magnet fixed near the sensor, adds the magnetic declination, warns when something disturbs the field, and serves a live web dashboard that you can open on a laptop or a phone. A digital compass is in every phone, drone and car navigation system, and it is more interesting than it look ...

PWM Solar Charge Controller Library for Proteus Simulation

PWM Solar Charge Controller Library for Proteus Simulation: an Arduino UNO V4.0, our INA219, a solar panel, the controller and a lead-acid battery

Hello friends, I hope you all are doing great. Today, I am going to share the new PWM Solar Charge Controller Library for Proteus Simulation , the next library of our renewable energy series. If you have searched for a Proteus simulation of a solar charge controller, the small box that sits between a solar panel, a battery and a load, this library brings the common 12 V / 24 V 10 A PWM controller into Proteus, with its charge stages, its pulses and its load terminals. Figure: The library at work: bulk, boost and float charge of a lead-acid battery from a solar panel. Updates PWM Solar Charge Controller Library for Proteus Simulation Latest version: V1.0 (November 2026, this tutorial) Other power libraries: LiPo Battery · Single Cell Battery · CR2032 Coin Cell · Solar Panel · MC34063 Buck · ...

IoT Combination Lock with ESP32 - Proteus Simulation

IoT Combination Lock with ESP32 - Proteus Simulation: the ESP32, the KY-040 dial, the MAX7219 matrix, the BTS7960, the door lock actuator and the bell

Hello friends, I hope you all are doing great. Today, I am going to share the IoT Combination Lock with ESP32 - Proteus Simulation , the thirty-first project of our IoT Projects series. If you have searched for a Proteus simulation of an ESP32 combination lock with a rotary encoder dial, here is a complete one. An ESP32 DevKit V1 turns a KY-040 rotary encoder into a safe's dial: you turn it to choose each digit and press it to enter the digit, a MAX7219 LED matrix shows the code as you go, a BTS7960 H-bridge drives a real car door lock actuator, an electric bell rings after three wrong codes, and a web dashboard can unlock and lock the door from a laptop or a phone. A rotary encoder looks like a potentiometer but works like two switches: as you turn it, they open and close in a set order, ...

18650 Li-ion Battery Library for Proteus Simulation

18650 Li-ion Battery Library for Proteus Simulation: an Arduino UNO V4.0, our INA219, the 18650 cell, a load resistor and a MOSFET switch

Hello friends, I hope you all are doing great. Today, I am going to share the new 18650 Li-ion Battery Library for Proteus Simulation , the next library of our renewable energy series. If you have searched for a Proteus simulation of an 18650 cell, the small lithium-ion cylinder inside laptop packs, power banks and torches, this library brings one into Proteus as a bare cell, with the voltage curve, the counted charge and the limits you have to respect yourself. Figure: The library at work: a capacity test from a full cell to the cut-off at 2.75 V. Updates 18650 Li-ion Battery Library for Proteus Simulation Latest version: V1.0 (November 2026, this tutorial) Other power libraries: LiPo Battery · Single Cell Battery · CR2032 Coin Cell · Solar Panel · MC34063 Buck · MC34064 Boost · 12V Solar ...

IoT Car Dashboard with ESP32 - Proteus Simulation

IoT Car Dashboard with ESP32 - Proteus Simulation: the ESP32, the X27.168 speedometer, the air-core tachometer, the L9110S and the LM393 speed sensor

Hello friends, I hope you all are doing great. Today, I am going to share the IoT Car Dashboard with ESP32 - Proteus Simulation , the twenty-ninth project of our IoT Projects series. If you have searched for a Proteus simulation of an ESP32 speedometer with real gauge needles, here is a complete one. An ESP32 DevKit V1 is the brain of a car's instrument cluster: it measures the wheel's speed with an LM393 slotted optical sensor, drives an X27.168 stepper speedometer straight from four pins, works out the engine's speed through a five-speed automatic gearbox and shows it on an air-core tachometer, counts the odometer and the trip, warns of overspeed, and serves a live web dashboard to a laptop and a phone. Most cars still show their speed with needles, and two clever little motors move them ...

12V Lead-Acid Battery Library for Proteus Simulation

12V Lead-Acid Battery Library for Proteus Simulation: an Arduino UNO V4.0, our INA219, the sealed lead-acid battery and the hand crank generator

Hello friends, I hope you all are doing great. Today, I am going to share the new 12V Lead-Acid Battery Library for Proteus Simulation , the next library of our renewable energy series. If you have searched for a Proteus simulation of a lead-acid battery, the heavy 12 V block that has started cars and kept alarm systems alive for generations, this library brings the sealed 12 V 7 Ah version of it into Proteus, with the behaviour that makes this old chemistry both easy and unforgiving. Figure: The library at work: the load drains the battery flat, the hand crank charges it and the charge left climbs. Updates 12V Lead-Acid Battery Library for Proteus Simulation Latest version: V1.0 (November 2026, this tutorial) Other power libraries: LiPo Battery · Single Cell Battery · CR2032 Coin Cell · S ...

IoT Robot Arm Controller with Raspberry Pi 5 - Proteus Simulation

IoT Robot Arm Controller with Raspberry Pi 5 - Proteus Simulation: the Raspberry Pi 5, the PCA9685 servo driver and the 4-DOF robot arm with its block

Hello friends, I hope you all are doing great. Today, I am going to share the IoT Robot Arm Controller with Raspberry Pi 5 - Proteus Simulation , the twenty-eighth project of our IoT Projects series. If you have searched for a Proteus simulation of a Raspberry Pi robot arm with a PCA9685 servo driver, here is a complete one. A Raspberry Pi 5 drives a 4-DOF desktop robot arm with four SG90 servos through a PCA9685 16-channel PWM driver on I2C. The program works out the joint angles for any point the claw should reach, moves every joint smoothly, picks up a block and places it on a second stand, jogs the claw up, down, out and in by millimetres, records poses and plays them back, all from a web dashboard on a laptop or a phone. Robot arms do the welding, the painting and the packing in facto ...

12V LiFePO4 Battery Library for Proteus Simulation

12V LiFePO4 Battery Library for Proteus Simulation: an Arduino UNO V4.0, our INA219, the LiFePO4 battery and the hand crank generator

Hello friends, I hope you all are doing great. Today, I am going to share the new 12V LiFePO4 Battery Library for Proteus Simulation , the next library of our renewable energy series. If you have searched for a Proteus simulation of a LiFePO4 battery, the lithium iron phosphate battery that is replacing the old 12 V lead-acid blocks everywhere, this library brings it into Proteus together with the part that makes it safe: its battery management system, the BMS. Figure: The library at work: the BMS cuts the empty battery off, the hand crank charges it and the charge left climbs. Updates 12V LiFePO4 Battery Library for Proteus Simulation Latest version: V1.0 (November 2026, this tutorial) Other power libraries: LiPo Battery · Single Cell Battery · CR2032 Coin Cell · Solar Panel · MC34063 Buc ...

IoT RGB Mood Lamp with ESP32 - Proteus Simulation

IoT RGB Mood Lamp with ESP32 - Proteus Simulation: the ESP32, the WS2812B ring of 16, the slide potentiometer and the push button in the RAINBOW mode

Hello friends, I hope you all are doing great. Today, I am going to share the IoT RGB Mood Lamp with ESP32 - Proteus Simulation , the twenty-seventh project of our IoT Projects series. If you have searched for a Proteus simulation of an ESP32 driving WS2812B NeoPixel LEDs, here is a complete one. An ESP32 DevKit V1 drives a ring of 16 addressable RGB LEDs as a mood lamp: a slide potentiometer sets the brightness, a push button steps through six light modes, and a web dashboard picks the mode and the colour and starts a sleep timer that fades the lamp out. Addressable LEDs such as the WS2812B, sold as NeoPixels, changed how people build lights: every LED has its own tiny controller, so one data wire sets the colour of every LED in a strip or a ring. In this tutorial, we will go through the ...

Hand Crank Generator Library for Proteus Simulation

Hand Crank Generator Library for Proteus Simulation: an Arduino UNO V4.0, our INA219 and the 20 W hand crank generator

Hello friends, I hope you all are doing great. Today, I am going to share the new Hand Crank Generator Library for Proteus Simulation , the next library of our renewable energy series. If you have searched for a Proteus simulation of a hand crank generator, the little emergency generator that makes electricity from nothing more than your own arm, this library brings it into Proteus: the handle, the hand that turns it, the generator and its load, all solved together. Figure: The library at work: the crank turns, and the volts, amps and watts follow the cadence. Updates Hand Crank Generator Library for Proteus Simulation Latest version: V1.0 (November 2026, this tutorial) Other power libraries: LiPo Battery · Single Cell Battery · CR2032 Coin Cell · Solar Panel · MC34063 Buck · MC34064 Boost ...