TEP DOWNLOAD CENTER

Project Files of Raspberry Pi 5 Tilt Alarm with MPU9250 and ST7735 (Proteus Simulation)

Libraries Code Projects Simulation
tep://download-terminal b6683df6faf9486996f2551853f6d0e6.zip ZIP archiveV1.0Verified0 downloadsFree
Raspberry Pi 5 Tilt Alarm with MPU9250 and ST7735 (Proteus Simulation): the Raspberry Pi 5, the GY-9250, the TFT showing DANGER and the coin motor vibrating
Proteus library · File 1 of 1

Raspberry Pi 5 Tilt Alarm with MPU9250 and ST7735 in Proteus Simulation V1.0

Raspberry Pi 5 Tilt Alarm with MPU9250 and ST7735 in Proteus Simulation V1.0 comes as a ZIP archive of 141 files (14.0 MB, 27.3 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, source code and a nested archive.

  • LIBProteus library
  • DLLProteus model
  • DSNProteus simulation
  • SRCSource code
  • ZIPNested archive

Description

Raspberry-Pi-5-Tilt-Alarm-MPU9250-ST7735-Proteus-Simulation-v1.0.zip: the complete Proteus simulation project (Raspberry Pi 5, the GY-9250 MPU9250, the 1.8" ST7735 TFT, the DRV8833, the coin vibration motor, the Laptop and Mobile WiFi Monitors), the Python program tilt_alarm.py, every LIB and DLL the simulation needs, the TEPPi Python runtime and a README.

Read Raspberry Pi 5 Tilt Alarm with MPU9250 and ST7735 (Proteus Simulation)

File Structure

b6683df6faf9486996f2551853f6d0e6.zip141 files · 24 folders · 27.3 MB unpacked
Pi-5-Tilt-Alarm-TEP-v1.0/141 files · 27.3 MB
Proteus Library Files/7 files · 281.7 KB
LIB TEPCOINVIB.LIBProteus library 13.2 KB
LIB TEPDRV8833.LIBProteus library 16 KB
LIB TEPLAPTOP.LIBProteus library 39.5 KB
LIB TEPMOBILE.LIBProteus library 13.1 KB
LIB TEPMPU9250.LIBProteus library 81.1 KB
LIB TEPRPI5.LIBProteus library 60.5 KB
LIB TEPTFT.LIBProteus library 58.4 KB
Proteus Model Files/125 files · 22.8 MB
TEPPi/120 files · 18.7 MB
python/33 files · 17.5 MB
DLL libcrypto-3.dllSimulation model 3.3 MB
DLL libffi-8.dllSimulation model 34.3 KB
DLL libssl-3.dllSimulation model 620.8 KB
TXT LICENSE.txtText file 36 KB
PYD pyexpat.pydPYD file 169.8 KB
CAT python.catCAT file 628.1 KB
EXE python.exeEXE file 99.3 KB
DLL python3.dllSimulation model 65.3 KB
DLL python311.dllSimulation model 4.8 MB
ZIP python311.zipArchive 4.1 MB
_PTH python311._pth_PTH file 80 B
EXE pythonw.exeEXE file 97.8 KB
PYD select.pydPYD file 26.8 KB
DLL sqlite3.dllSimulation model 1.2 MB
PYD unicodedata.pydPYD file 1.1 MB
DLL vcruntime140.dllSimulation model 88.9 KB
PYD winsound.pydPYD file 27.3 KB
PYD _asyncio.pydPYD file 55.8 KB
PYD _bz2.pydPYD file 79.8 KB
PYD _ctypes.pydPYD file 105.8 KB
PYD _decimal.pydPYD file 193.8 KB
PYD _elementtree.pydPYD file 113.8 KB
PYD _hashlib.pydPYD file 48.8 KB
PYD _lzma.pydPYD file 145.8 KB
PYD _msi.pydPYD file 36.8 KB
PYD _multiprocessing.pydPYD file 29.3 KB
PYD _overlapped.pydPYD file 42.3 KB
PYD _queue.pydPYD file 28.8 KB
PYD _socket.pydPYD file 67.3 KB
PYD _sqlite3.pydPYD file 89.3 KB
PYD _ssl.pydPYD file 153.8 KB
PYD _uuid.pydPYD file 22.8 KB
PYD _zoneinfo.pydPYD file 38.8 KB
runtime/87 files · 1.1 MB
Adafruit_BBIO/6 files · 22.6 KB
PYC ADC.pycPYC file 2.1 KB
PYC GPIO.pycPYC file 9.9 KB
PYC PWM.pycPYC file 4.1 KB
PYC UART.pycPYC file 1.3 KB
PYC _pins.pycPYC file 4.7 KB
PYC __init__.pycPYC file 431 B
Adafruit_DHT/1 file · 2.5 KB
PYC __init__.pycPYC file 2.5 KB
arduino/2 files · 17.7 KB
app_utils/1 file · 17.5 KB
PYC __init__.pycPYC file 17.5 KB
PYC __init__.pycPYC file 283 B
colorzero/8 files · 85.3 KB
SRC attr.pySource file 6.5 KB
SRC color.pySource file 37.9 KB
SRC conversions.pySource file 11.1 KB
SRC deltae.pySource file 5.5 KB
SRC easings.pySource file 885 B
SRC tables.pySource file 13.6 KB
SRC types.pySource file 9 KB
SRC __init__.pySource file 878 B
colorzero-2.0.dist-info/5 files · 6.6 KB
TXT LICENSE.txtText file 1.5 KB
FILE METADATAFile 4 KB
FILE RECORDFile 1004 B
TXT top_level.txtText file 10 B
FILE WHEELFile 110 B
gpiozero/27 files · 594.5 KB
fonts/3 files · 12.6 KB
TXT 14seg.txtText file 2.6 KB
TXT 7seg.txtText file 1.1 KB
SRC __init__.pySource file 8.9 KB
pins/11 files · 234.3 KB
SRC data.pySource file 58.5 KB
SRC lgpio.pySource file 12.4 KB
SRC local.pySource file 6.6 KB
SRC mock.pySource file 18.5 KB
SRC native.pySource file 20.7 KB
SRC pi.pySource file 27.8 KB
SRC pigpio.pySource file 21.1 KB
SRC rpigpio.pySource file 7.1 KB
SRC spi.pySource file 7.7 KB
SRC style.pySource file 2.7 KB
SRC __init__.pySource file 51.2 KB
SRC boards.pySource file 100.9 KB
SRC compat.pySource file 1.2 KB
SRC devices.pySource file 24.3 KB
SRC exc.pySource file 7.4 KB
SRC input_devices.pySource file 53.6 KB
SRC internal_devices.pySource file 26.1 KB
SRC mixins.pySource file 20.5 KB
SRC output_devices.pySource file 60.5 KB
SRC spi_devices.pySource file 19.6 KB
SRC threads.pySource file 1.6 KB
SRC tones.pySource file 8.4 KB
SRC tools.pySource file 20.9 KB
SRC __init__.pySource file 2.6 KB
gpiozero-2.0.1.post3.dist-info/6 files · 14.6 KB
TXT entry_points.txtText file 539 B
RST LICENSE.rstRST file 1.4 KB
FILE METADATAFile 9.7 KB
FILE RECORDFile 2.8 KB
TXT top_level.txtText file 21 B
FILE WHEELFile 92 B
Jetson/2 files · 8.2 KB
GPIO/1 file · 7.9 KB
PYC __init__.pycPYC file 7.9 KB
PYC __init__.pycPYC file 264 B
micropython/11 files · 142.1 KB
PYC dht.pycPYC file 3.4 KB
PYC ds18x20.pycPYC file 3.8 KB
PYC framebuf.pycPYC file 17.5 KB
PYC machine.pycPYC file 55.2 KB
PYC micropython.pycPYC file 3.3 KB
PYC network.pycPYC file 10.8 KB
PYC ntptime.pycPYC file 1.5 KB
PYC onewire.pycPYC file 4.2 KB
PYC requests.pycPYC file 7.3 KB
PYC rp2.pycPYC file 2.5 KB
PYC tep_mpy.pycPYC file 32.6 KB
OPi/2 files · 14.8 KB
PYC GPIO.pycPYC file 14.5 KB
PYC __init__.pycPYC file 283 B
RPi/2 files · 17.6 KB
PYC GPIO.pycPYC file 17.4 KB
PYC __init__.pycPYC file 257 B
serial/2 files · 15.2 KB
PYC serialutil.pycPYC file 691 B
PYC __init__.pycPYC file 14.5 KB
smbus2/1 file · 12.8 KB
PYC __init__.pycPYC file 12.8 KB
PYC adafruit_dht.pycPYC file 3.6 KB
PYC board.pycPYC file 1.7 KB
PYC lgpio.pycPYC file 37 KB
PYC smbus.pycPYC file 418 B
PYC spidev.pycPYC file 6.2 KB
PYC tep_opi.pycPYC file 7 KB
PYC tep_pi.pycPYC file 37.3 KB
PYC tep_pi_boot.pycPYC file 10.6 KB
PYC tep_pi_fs.pycPYC file 23.7 KB
PYC tep_pi_net.pycPYC file 28.7 KB
PYC tep_pi_w1.pycPYC file 8.8 KB
PYC wiringpi.pycPYC file 16.9 KB
DLL TEPCOINVIB.DLLSimulation model 278 KB
DLL TEPDRV8833.DLLSimulation model 312.5 KB
DLL TEPMPU9250.DLLSimulation model 373.5 KB
DLL TEPNET.DLLSimulation model 2.9 MB
DLL TEPTFT.DLLSimulation model 310.5 KB
Proteus Simulation/7 files · 4.2 MB
DSN Pi-5-Tilt-Alarm.pdsprjProteus simulation 34.4 KB
DLL TEPCOINVIB.DLLSimulation model 278 KB
DLL TEPDRV8833.DLLSimulation model 312.5 KB
DLL TEPMPU9250.DLLSimulation model 373.5 KB
DLL TEPNET.DLLSimulation model 2.9 MB
DLL TEPTFT.DLLSimulation model 310.5 KB
SRC tilt_alarm.pySource file 19.8 KB
Python Code/1 file · 19.8 KB
SRC tilt_alarm.pySource file 19.8 KB
TXT README.txtText file 10.3 KB

README

README.txt 138 lines
===============================================================================================================
  Raspberry Pi 5 Tilt Alarm with MPU9250 and ST7735 (Proteus Simulation) - Project V1.0
  The Engineering Projects - www.TheEngineeringProjects.com
===============================================================================================================

IMPORTANT LINKS
  The project tutorial (circuit, code, simulation results):
    https://www.theengineeringprojects.com/2026/11/raspberry-pi-5-tilt-alarm-mpu9250-st7735-proteus-simulation.html
  The libraries this project is built from (each post has its own full download and tutorial):
    Raspberry Pi 5 board:
      https://www.theengineeringprojects.com/2026/10/raspberry-pi-5-library-for-proteus.html
    MPU9250 IMU (GY-9250):
      https://www.theengineeringprojects.com/2026/10/mpu9250-library-for-proteus-v1-0.html
    TFT 1.8" ST7735:
      https://www.theengineeringprojects.com/2026/10/tft-st7735-library-for-proteus-v1-0.html
    DRV8833 motor driver:
      https://www.theengineeringprojects.com/2026/11/drv8833-motor-driver-library-for-proteus.html
    Coin vibration motor:
      https://www.theengineeringprojects.com/2026/10/coin-vibration-motor-library-for-proteus-v1-0.html
    Laptop WiFi Monitor:
      https://www.theengineeringprojects.com/2026/10/laptop-wifi-monitor-library-for-proteus.html
    Mobile WiFi Monitor:
      https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
  Support our free work: https://www.theengineeringprojects.com/donate

FILE STRUCTURE
Pi-5-Tilt-Alarm-TEP-v1.0/
|-- Proteus Library Files/
|   |-- TEPCOINVIB.LIB                                 13.2 KB   a part of the project -> LIBRARY folder
|   |-- TEPDRV8833.LIB                                 16.0 KB   a part of the project -> LIBRARY folder
|   |-- TEPLAPTOP.LIB                                  39.5 KB   a part of the project -> LIBRARY folder
|   |-- TEPMOBILE.LIB                                  13.1 KB   a part of the project -> LIBRARY folder
|   |-- TEPMPU9250.LIB                                 81.1 KB   a part of the project -> LIBRARY folder
|   |-- TEPRPI5.LIB                                    60.5 KB   a part of the project -> LIBRARY folder
|   |-- TEPTFT.LIB                                     58.4 KB   a part of the project -> LIBRARY folder
|-- Proteus Model Files/
|   |-- TEPCOINVIB.DLL                                278.0 KB   a model -> MODELS folder
|   |-- TEPDRV8833.DLL                                312.5 KB   a model -> MODELS folder
|   |-- TEPMPU9250.DLL                                373.5 KB   a model -> MODELS folder
|   |-- TEPNET.DLL                                     2.89 MB   a model -> MODELS folder
|   |-- TEPTFT.DLL                                    310.5 KB   a model -> MODELS folder
|   |-- TEPPi/python/                                 17.54 MB   Python 3.11 embeddable -> MODELS\TEPPi (33 files)
|   |-- TEPPi/runtime/                                 1.11 MB   TEP Pi runtime, gpiozero -> MODELS\TEPPi (87 files)
|-- Proteus Simulation/
|   |-- Pi-5-Tilt-Alarm.pdsprj                         34.4 KB   the project simulation
|   |-- TEPCOINVIB.DLL                                278.0 KB   copy of the model
|   |-- TEPDRV8833.DLL                                312.5 KB   copy of the model
|   |-- TEPMPU9250.DLL                                373.5 KB   copy of the model
|   |-- TEPNET.DLL                                     2.89 MB   copy of the model
|   |-- TEPTFT.DLL                                    310.5 KB   copy of the model
|   |-- tilt_alarm.py                                  19.8 KB   the program PI1 runs
|-- Python Code/
|   |-- tilt_alarm.py                                  19.8 KB   the program (the same file)
|-- README.txt                                        ~10.3 KB   this file
Total: 27.29 MB (unzipped). The C++ source code of the models is not included.

WHAT IS IT?
  A digital spirit level and tilt alarm you can run in Proteus, the kind fitted to cranes, aerial platforms, tractors
  and caravans: a Raspberry Pi 5 reads an MPU-9250's accelerometer and gyro, shows a bubble level on a 1.8" TFT,
  buzzes a coin vibration motor when the tilt goes too far, and serves a web dashboard.
    * GY-9250 (MPU9250ADVTEP, U1) on I2C1 at 0x68: SDA GPIO2 (pin 3), SCL GPIO3 (pin 5); VCC from the Pi's 5 V pin
      (pin 2) - the module's regulator gives the chip 3.3 V; AD0 open.
    * TFT 1.8" ST7735 128 x 160 (TFT18ST7735ADVTEP) on SPI0: SDA = MOSI GPIO10 (pin 19), SCK = SCLK GPIO11 (pin 23),
      CS = CE0 GPIO8 (pin 24), A0 = GPIO25 (pin 22), RESET = GPIO24 (pin 18); VCC and LED on 3V3 (pin 1).
    * DRV8833 (DRV8833TEP, U2) on the Pi's 5 V: IN1 = GPIO18 (pin 12, PWM), IN2 = GPIO23 (pin 16), EEP (sleep) =
      GPIO22 (pin 15); IN3 / IN4 to GND (bridge B unused); OUT1 / OUT2 to the coin motor.
    * A 3 V coin vibration motor (COINVIBTEP, M1) on bridge A.
    * RASPBERRY PI 5 (PI1) runs tilt_alarm.py on Ethernet at 192.168.1.51 (port 8000).
    * Laptop WiFi Monitor (PC1) and Mobile WiFi Monitor (MOB1) open http://192.168.1.51:8000/.
  The rules (at the top of the program):
    * the pitch and the roll from the accelerometer, blended with the gyro (a complementary filter with a 1 s time
      constant: 98 % gyro, 2 % accelerometer at 50 readings a second); the tilt = the angle between the board's Z
      axis and the vertical, cos(tilt) = cos(pitch) x cos(roll);
    * ZERO: the present attitude becomes level (the reference is stored);
    * LEVEL under 1 deg, OK, WARNING from 10 deg (a 0.2 s buzz every second at 50 % of 5 V), DANGER from 20 deg (a
      steady buzz at 60 %), each left 1 deg inside its threshold; MUTE silences the buzz until the alarm clears;
    * the motor is braked at the end of each buzz (both DRV8833 inputs high) and the driver put to sleep.
  Its pages:
    /          the dashboard: the state, the tilt, the pitch and the roll, the buzz, the reference, the events
    /zero      the present attitude becomes level      /mute      silence the buzz      /data      everything as JSON
  No extra Python library: lgpio and spidev (in the TEPPi runtime and on Raspberry Pi OS), threading, http.server.

TEST STATUS
  Tested in Proteus 8 Professional on Windows 11, the run that made the tutorial's screenshots (the program's times):
  - Start: WHO_AM_I 0x71; the gyro's bias 1.39, -0.89, 0.59 deg/s; the board flat, but the chip's own offset reads
    pitch +1.0, roll -0.7: "OK 1.2" on the TFT (SPI at 8 MHz). The loop reads the sensor 50 times a second.
  - 12.9 s ZERO from the laptop: "this attitude is level now - the reference pitch +1.0, roll -0.7 deg": LEVEL 0.0.
  - 14.6 s PITCH +5 (the gyro saw +49.6 deg/s): OK 4.9. 17.9 s PITCH +5 again: "WARNING: tilt 10.1 deg"; it settles
    at 9.8 and stays WARNING (left only under 9.0); 0.2 s pulses at 50 %, the motor near 9,000 RPM in each.
  - 24.2 s ROLL +15 (+90 deg/s): tilt 17.8. 26.3 s PITCH +5: "DANGER: tilt 20.1 deg", then 20.6 at pitch +14.6, roll
    +14.6; a steady buzz at 60 %: 2.95 V average, 11,709 RPM = 195 Hz, 0.77 G on 100 g, 69 mA.
  - 29.3 s MUTE from the phone: the motor stopped, the TFT still DANGER with MUTE. 32.0 s FLAT: WARNING, 32.1 s OK -
    "the alarm cleared - MUTE off", 32.2 s LEVEL 0.3 (the gyro saw -89 deg/s on both axes).
  - 36.6 s of simulation in 510 s.

INSTALLATION
  1. Close Proteus. Extract the WHOLE zip file, for example to your Desktop.
  2. Copy the files from "Proteus Library Files" into the LIBRARY folder of Proteus, for example
     C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
  3. Copy everything in "Proteus Model Files" - the DLL files and the TEPPi folder - into the MODELS folder (next
     to LIBRARY).
  4. Start Proteus. Press P in the schematic and search for RASPBERRY PI 5, MPU9250ADVTEP or COINVIBTEP to check
     that the parts are there.

RUN THE SIMULATION
  1. Open "Proteus Simulation\Pi-5-Tilt-Alarm.pdsprj". Keep tilt_alarm.py and the DLL files beside it.
  2. Press Play. The TFT shows the bubble; the Pi's terminal prints the angles every second.
  3. Open the Laptop WiFi Monitor (PC1) or the Mobile WiFi Monitor (MOB1), press Go, and press ZERO.
  4. Tilt the board from the GY-9250's pop-up (PITCH / ROLL +5, +15): WARNING at 10 deg, DANGER at 20 deg, and
     the coin motor buzzes. MUTE silences it; FLAT clears the alarm.
  Your own program: edit tilt_alarm.py.

PROPERTIES USED IN THIS PROJECT
  PI1 RASPBERRY PI 5           PROGRAM=tilt_alarm.py, ETHERNET=IN (192.168.1.51)
  U1 MPU9250ADVTEP             CHIP=MPU9250, PITCH=0, ROLL=0 (the board turned from the pop-up), NOISE=1
  TFT1 TFT18ST7735ADVTEP       (the defaults: a black-tab glass)
  U2 DRV8833TEP                (the defaults);  M1 COINVIBTEP  (the defaults: mounted on 100 g)
  PC1, MOB1                    HOMEPAGE=http://192.168.1.51:8000/

TROUBLESHOOTING
  * The TFT stays white: check A0 (GPIO25), RESET (GPIO24) and CS (CE0); its pop-up says what it is waiting for.
  * The bubble moves the wrong way: the bubble floats to the HIGH side, as in a real level - nose up moves it up.
  * The angles drift slowly: the gyro's bias is measured in the first second - keep the board still at the start.
  * The motor never buzzes: EEP (GPIO22) must be high; no 5 V on the DRV8833's VCC; or MUTE is on.
  * The terminal cannot start Python: the TEPPi folder is not in MODELS.

LICENCES
  * The project, the program, the parts (LIB files) and the models (DLL files) are made by The Engineering Projects
    and are free for learning and for your own projects. The models use only standard Windows libraries.
    The C++ source code of the models is not included; the source code is not included for any model.
  * TEPPi\python is the Python 3.11 Windows embeddable package (Python Software Foundation License); TEPPi\runtime
    holds our TEP Pi runtime with gpiozero and colorzero (BSD licences) - their licence files are inside the folders.
  * Proteus is a product of Labcenter Electronics and is not included. Raspberry Pi is a trademark of Raspberry Pi
    Ltd. This project is not made or endorsed by them or by the makers of the MPU-9250, the ST7735 and the DRV8833.

VERSION
  V1.0 - the first release of the project.
===============================================================================================================
Advertisement

Development1 release

  1. V1.0Raspberry Pi 5 Tilt Alarm with MPU9250 and ST7735 in Proteus Simulation V1.0this page

    V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.

Installation7 steps

From the download to a working project, in order. The steps follow what the package contains.

You will need

  • Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
  • Pythonto build the source files into firmware
  • Any archive toolWindows, macOS and Linux extract ZIP files on their own

Steps

  1. 1

    Extract the archive

    Right-click b6683df6faf9486996f2551853f6d0e6.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (Pi-5-Tilt-Alarm-TEP-v1.0) as it is.

  2. 2

    Copy the library files into Proteus

    Move TEPCOINVIB.LIB, TEPDRV8833.LIB and TEPLAPTOP.LIB and 4 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.

  3. 3

    Add the simulation model

    Copy TEPCOINVIB.DLL, TEPDRV8833.DLL and TEPMPU9250.DLL and 9 more into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.

  4. 4

    Restart Proteus and place the component

    Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.

  5. 5

    Build the source code

    Open tilt_alarm.py, attr.py and color.py and 28 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.

  6. 6

    Open the example simulation

    Open Pi-5-Tilt-Alarm.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.

  7. 7

    Follow the tutorial

    Raspberry Pi 5 Tilt Alarm with MPU9250 and ST7735 (Proteus Simulation) explains every connection and setting in order; keep it open beside the files while you build.

How to add a library in Proteus 8

FAQs8 questionsContact TEP

How do I download Raspberry Pi 5 Tilt Alarm with MPU9250 and ST7735 in Proteus Simulation V1.0?

Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.

What is inside the archive?

Raspberry Pi 5 Tilt Alarm with MPU9250 and ST7735 in Proteus Simulation V1.0 comes as a ZIP archive of 141 files (14.0 MB, 27.3 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, source code and a nested archive. Open the File Structure tab for the full list of 141 files.

What should I do if the download does not start?

Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.

Is this file free?

Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.

How do I check that the file arrived complete?

Compare its SHA-256 with the one on this page, 4de81cdb1cdba08c42fae97195f012f69983c5e62b277148a1b9d6dc13bf8541. In PowerShell run Get-FileHash "b6683df6faf9486996f2551853f6d0e6.zip"; on macOS or Linux run shasum -a 256 "b6683df6faf9486996f2551853f6d0e6.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.

Do I need WinRAR to open the ZIP file?

No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.

Where do I put the LIB and IDX files?

Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.

Which Proteus version does the library need?

The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.

preparing · b6683df6faf9486996f2551853f6d0e6.zip
Rating
Your download will be ready shortly
Preparing your download…

Members skip the wait. Log in or join TEP.

Last 14 days0 downloads
SHA-256 4de81cdb1cdba08c42fae97195f012f69983c5e62b277148a1b9d6dc13bf8541
DocumentationRaspberry Pi 5 Tilt Alarm with MPU9250 and ST7735 (Proteus Simulation)
Need help with this file? Bug report Ask a question Download problemsGet updates
Advertisement

Comments

0

Join the conversation

Start the conversationAsk a question or share how you used this download.