Project Files of SIM800C Library for Proteus V1.1 (GSM Module + Arduino)
sim800c-tep-v1-1-52adc4a1af6c40229f8ae3a42dbe6ada.zip

SIM800C GSM Library for Proteus V1.1
SIM800C GSM Library for Proteus V1.1 comes as a ZIP archive of 23 files (1.4 MB, 3.2 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and data files.
- LIBProteus library
- IDXProteus library index
- DLLProteus model
- DSNProteus simulation
- INOArduino sketch
- LIBArduino library
- HEXHEX firmware
- CSVData file
Description
SIM800C GSM Library for Proteus V1.1 is the download package that goes with our tutorial SIM800C Library for Proteus V1.1 (GSM Module + Arduino). On this page you can download the ZIP file (1.4 MB) and see what is inside before you save it: 23 files in 9 folders, the Proteus library files (LIB and IDX), the simulation model (DLL), a ready Proteus simulation, an Arduino sketch, an Arduino library, the compiled HEX firmware and data files. The tutorial explains the design; this page gets the files onto your computer and into use.
What this library is
SIM800C-GSM-Library-for-Proteus-v1.1.zip with SIM800C Simple and Advance (TEPSIM800C.LIB and TEPSIMCOM.DLL), the TEP Serial Monitor and Arduino UNO libraries for Proteus, the SMS remote control simulation with its HEX file, the demo sketch with the AltSoftSerial 1.4 library and a README.
This is version 1.1; older or newer releases, when they exist, are listed in the Development tab.
What is inside the ZIP file
- ArduinoV3TEP.LIB – Proteus library, 95.6 KB
- TEPSERIALMON.LIB – Proteus library, 11.1 KB
- TEPSIM800C.LIB – Proteus library, 83.4 KB
- ArduinoV3TEP.IDX – Library index, 830 B
- TEPSERIALMON.DLL – Simulation model, 978 KB
- TEPSIMCOM.DLL – Simulation model, 472 KB
- and 17 more, all listed in the File Structure tab
The archive unpacks to 3.2 MB and carries its own README (README.txt), shown in the README tab above.
How to download
Use the download panel at the top of this page: after the counter (30 seconds for guests, 10 for members) the black button unlocks and the ZIP file comes straight from our content network. If the browser opens it instead of saving, use Save as; extract the whole archive before using anything inside it.
How to install
- Step 1: Extract the ZIP file with Windows (Extract All), 7-Zip or WinRAR, keeping its folders.
- Step 2: Close Proteus and copy ArduinoV3TEP.LIB, TEPSERIALMON.LIB and TEPSIM800C.LIB and ArduinoV3TEP.IDX into its LIBRARY folder (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY).
- Step 3: Copy TEPSERIALMON.DLL and TEPSIMCOM.DLL into the MODELS folder next to it, so the part simulates.
- Step 4: Start Proteus, press P and search for "ArduinoV3TEP"; place and wire it as in the tutorial.
- Step 5: In the Arduino IDE use Sketch → Include Library → Add .ZIP Library, then restart the IDE.
- Step 6: Open SIM800C_SMS_Control.ino, Echo.ino and ReceiveTest.ino in the Arduino IDE, pick board and port and Verify (Export Compiled Binary gives the HEX).
- Step 7: In Proteus set the controller's Program File to SIM800C_SMS_Control.hex; on hardware, flash the same file.
- Step 8: Open SIM800C-SMS-Control-ArduinoUnoV3.pdsprj in Proteus and press Play.
Read the detailed guide
This page is for the files. The full tutorial, SIM800C Library for Proteus V1.1 (GSM Module + Arduino), explains the circuit and the code step by step and shows the working results and the simulation; read it before you build. Questions about the download or the installation go in the comments below; more Proteus downloads are listed further down this page.
File Structure
4.6 KB9.8 KB968 B1.4 KB8.3 KB2.5 KB82 B441 B422 B1.3 KB384 B14.6 KB830 B95.6 KB11.1 KB83.4 KB978 KB472 KB25.6 KB33.1 KB978 KB472 KB34.1 KBGallery12 images from the tutorialOpen the tutorial
The circuit, the board and the results as they appear in SIM800C Library for Proteus V1.1 (GSM Module + Arduino). Open an image for its full size.












README
SIM800C GSM / GPRS MODULE (SIMCom, HW-537 board) LIBRARY FOR PROTEUS - V1.1
Designed by The Engineering Projects
www.TheEngineeringProjects.com
IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
https://www.theengineeringprojects.com/2026/10/sim800c-library-for-proteus.html
Report a bug or suggest a feature (our forum):
https://www.theengineeringprojects.com/forum/category/sim800c-proteus-library
The demo uses our TEP Serial Monitor Advance (included) instead of Proteus's
Virtual Terminal - its own article:
https://www.theengineeringprojects.com/2026/10/serial-monitor-advance-proteus-library.html
FILE STRUCTURE
SIM800C-TEP-v1.1/
|-- Proteus Library Files/
| |-- ArduinoV3TEP.IDX 0.8 KB its index -> LIBRARY folder
| |-- ArduinoV3TEP.LIB 95.6 KB TEP Arduino UNO (demo) -> LIBRARY folder
| |-- TEPSERIALMON.LIB 11.1 KB TEP Serial Monitor Advance -> LIBRARY folder
| |-- TEPSIM800C.LIB 83.4 KB SIM800C Simple + Advance (2 devices) -> LIBRARY folder
|-- Proteus Model Files/
| |-- TEPSERIALMON.DLL 978.0 KB Serial Monitor model -> MODELS folder
| |-- TEPSIMCOM.DLL 472.0 KB SIM800C model (shared with the SIM900A library) -> MODELS
|-- Proteus Simulation/
| |-- SIM800C_SMS_Control.hex 33.1 KB both UNOs (SMS remote control v1.1)
| |-- SIM800C-SMS-Control-ArduinoUnoV3.pdsprj 25.6 KB demo: UNO 1 + SIM800C Simple, UNO 2 + Advance
| |-- TEPSERIALMON.DLL 978.0 KB copy of the monitor model
| |-- TEPSIMCOM.DLL 472.0 KB copy of the model so the demo runs as is
|-- Arduino Code/
| |-- SIM800C_SMS_Control/SIM800C_SMS_Control.ino 14.6 KB sketch (source of the .hex)
| |-- libraries/AltSoftSerial/ 30.1 KB AltSoftSerial 1.4 (MIT, LICENSE.txt), 11 files
|-- README.txt ~35.1 KB this file
Total: 3.15 MB (unzipped). The C++ source code of the model is not included.
WHAT IS IT?
A simulation model of the SIMCom SIM800C GSM / GPRS module on the popular blue
HW-537 board for Proteus 8. It talks to your Arduino like the real one: the
board stays OFF after power-up until its PWX (power key) pin is held LOW for
more than 1 s, then the module learns the baud rate from the first "AT"
(auto-bauding), sends +CPIN: READY, Call Ready and SMS Ready, registers to the
network and answers the AT commands for SMS (text mode), calls, the network,
the clock and USSD. Next to the module there is a virtual smartphone with its
own number: it texts the module, calls it, answers its calls and shows the SMS
it receives as chat bubbles. Every TEP SIM800C, every TEP SIM900A and every
virtual phone in a design share one simulated network, so modules can also
text and call each other. The part looks like the blue HW-537 board with the
silver SIM800C, its IPEX socket and the flexible GSM antenna. While the
simulation runs the blue PWR LED shows the board's 5 V, the blue NET LED blinks
like the real NETLIGHT (slow while searching, every 3 s when registered), a
ring LED round the antenna lead and the lamp in the antenna's tip light orange
while the module sends and green while it receives, and the radio waves above
the antenna ripple out (sending) or in (receiving).
TWO DEVICES IN ONE LIBRARY (search "SIM800C" or "GSM" in Pick Devices):
SIM800C Simple device SIM800CTEP "SIM800C GSM / GPRS Module (SIMCom, HW-537 board) - Simple"
On-Sheet Panel: the virtual phone is drawn on the schematic
next to the module (the v1.0 phone) - click its CALL, HANG UP,
SMS and NETWORK buttons. The red X in the phone's app bar
closes it, the PANEL button on the board opens it again.
Your v1.0 designs keep working with this device.
SIM800C Advance device SIM800CADVTEP "SIM800C GSM / GPRS Module (SIMCom, HW-537 board) - Advance"
Pop-Up Panel: only the module board on the schematic; at Run
a TEP pop-up window opens - the same look as the TEP Serial
Monitor (move it by its header, resize it, minimise it). The
tabs Phone and Test sit in the header; the gear and ? icons
open Settings and Help; the palette icon switches the theme:
Phone the virtual phone redrawn for the window (signal
bars, chat bubbles, call bar, CALL / ANSWER, HANG
UP, the four SMS, GOOD / WEAK / NO SIGNAL) beside
three cards: MODULE (number, IMEI, firmware, UART
speed, the settings your sketch made, power and
start-ups, the PWX power key), NETWORK
(registration, CSQ and dBm, operator, how long it
is registered and how long the search took, which
start-up messages came, the NETLIGHT pattern) and
TRAFFIC (SMS sent / received / waiting at the SMS
centre, stored on the SIM, calls, AT commands and
errors, the last AT command with its reply and
response time)
Test four GSM test tools, all measured on the model:
Network - the module really restarts (switched off
and on again with its power key: PWRKEY LOW for
1 s, as the HW-537's PWX pin does) or switches
its radio off and on (AT+CFUN=0 / 1) 3, 5 or 10
times: the time of power-on, +CPIN READY, Call
Ready, SMS Ready and the registration of each
run, fastest / average / slowest
SMS round trip - the phone texts LED ON, LED OFF,
STATUS or HELLO 3, 5 or 10 times; each reply SMS
from your sketch stops the clock: network in +
your sketch + the reply back, answered / no
answer, the reply text
Call - the phone calls the module 1, 3 or 5 times:
the first RING, the RING URCs, the module's own
+CLIP line, the RI pin (how often and how long
LOW), whether your sketch answers (ATA) or
rejects (ATH) and after how long; a timeline
AT check - what the AT queries answer right now
(AT+CPIN? AT+CSQ AT+CREG? AT+COPS? AT+CMGF?
AT+CNMI? AT+CLIP? AT+CMEE? AT+CFUN? AT+IPR?
AT+CCALR? AT+CCLK?) and the last 8 AT commands
your Arduino sent with the reply and the
response time
Settings theme (TEP Dark / Light), text size, open at Run,
window size - remembered for your Windows user
Help Help & Support like the TEP Serial Monitor: report
a bug, suggest a feature, article, user guide,
updates, donate, website, forum; Copy diagnostics
(module, network, traffic, test results) for a
bug report
The OPEN PANEL button on the board opens the window again
after you close it.
Both devices use the same model and the same properties.
ONE MODEL FOR TWO LIBRARIES
The model TEPSIMCOM.DLL (the same name as in v1.0) is shared with the SIM900A
library: the TEP SIM900A GSM library ships the identical TEPSIMCOM.DLL (the
same bytes), so installing both libraries is safe - copying the DLL twice just
overwrites it with itself. A SIM800C and a SIM900A in the same design can text
and call each other.
NEW IN V1.1
* The SIM800C and the SIM900A are now two separate libraries (TEPSIM800C.LIB and
TEPSIM900A.LIB, one package each), with one shared model DLL.
* Two devices: SIM800C Simple (phone on the sheet, close / open) and SIM800C
Advance (pop-up window with the phone, test tools, settings and help) - see
above. The Advance device has its own default numbers (+15555550102 / phone
+15555550192), so a Simple and an Advance module in one design stay distinct.
* Board: a ring LED round the antenna lead and a lamp in the antenna tip
(orange = sending, green = receiving), a PANEL / OPEN PANEL button and a
SIMPLE / ADVANCE badge; the title moved up so the button never covers it.
The PWR and NET LEDs stay blue, like the two LEDs of the real HW-537, and
the NET LED keeps its real blink patterns.
* Model: the network search now takes 2.2 - 3.2 s (weak signal 2.8 - 3.4 s,
v1.0: always 3 s); every SMS takes its own time on the network, like on a
real one: 1.2 - 1.9 s from the phone to the module and 1.7 - 2.5 s from
the module to the phone (v1.0: always 1.5 s and 2 s; with a weak signal
2.5 x as long); AT+CFUN=1 after AT+CFUN=0 reports +CREG: 2 (searching);
AT+CFUN=1,1 answers OK completely before it restarts (v1.0 restarted after a
fixed 30 ms, which cut the OK at slow baud rates); the phone shows 60
characters per message (v1.0 cut longer replies at 32); every module event
reaches the Simulation Log (v1.0 could skip one when two happened at once).
* The demo uses the TEP Serial Monitor Advance instead of Virtual Terminals -
one monitor per Arduino (U3 = UNO 1, U4 = UNO 2) with quick buttons - and
shows both styles: UNO 1 with SIM800C Simple, UNO 2 with SIM800C Advance, an
LED on A0 of each UNO.
* The demo sketch (v1.1) also takes commands from the Serial Monitor (AT lines
go to the SIM800C and its answer is printed, STATUS, TEXT <message>, HELP),
and every 30 s it checks the module: after a restart (the module then forgets
its settings) it sets the SIM800C up again, and if the module is OFF (a
power-down) it switches it on with PWX first.
* Version 1.1 everywhere; the C++ source code is no longer included.
TEST STATUS
v1.0 was tested in Proteus 8.5 SP0 (1 Oct 2026) with the v1.0 demo: the sketch
switched the SIM800C on with PWX, registered (CSQ 22, TEP MOBILE), answered LED
ON by SMS (the RI interrupt fired) and rejected a call; the line monitor showed
+CLIP: "+15555550191",145,"",0,"",0.
v1.1 was tested in Proteus 8.5 SP0 (6 Oct 2026) with this package's demo: both
Serial Monitors and the Advance pop-up open at Run (no system caption row);
both sketches switch their SIM800C on with the PWX pulse and register (TEP
MOBILE). U1 (Simple): SMS LED ON / LED OFF / STATUS /
HELLO from the phone (D1 lights, replies in the chat), CALL (rejected with ATH,
the RI interrupt fires), WEAK (CSQ 7) and NO SIGNAL (+CREG: 0,2, +CSQ: 99,99),
the red X and PANEL. U2 (Advance): the phone, Test > Network restart x 5 (9.05 -
9.48 s, average 9.24 s; the sketch set the module up again each time), SMS round
trip x 5 (3.31 - 4.01 s), Call x 3 (first RING 2.00 s, rejected 0.05 s later,
RI low 52 ms), AT check, Settings, Help, close and OPEN PANEL.
PC tests: 1667 automatic checks
on a PC (for the shared model, both modules): 243 on the module model at the
pin level (power key, sync bytes, auto-bauding, identity strings, SMS, calls
and +CLIP, RI, no signal and the SMS centre, USSD, clock, power down, fixed
baud rate, and the v1.1 network spread, SMS times, AT+CFUN, AT log and test
tools with their measured times); 95 with the two real demo sketches running
against the model (start-up with the PWX pulse, SMS commands, calls, an UNO
reset, the Serial Monitor commands, the pop-up's tools with the real sketch,
setting the module up again after a restart and switching it on again after a
power-down); 222 on the complete Proteus model (all four devices, the LEDs and
the antenna ring, the phone close / open, a v1.0 design, the pop-up window,
its pages and buttons, the four test tools); 1107 on the rendered pop-up
windows (every tool's hint lines fit the window).
INSTALLATION (about 2 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" (TEPSIM800C.LIB with both devices,
TEPSERIALMON.LIB and the TEP Arduino UNO V3 library ArduinoV3TEP.LIB / .IDX
used by the demo) to the LIBRARY folder of Proteus, for example:
C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
(on some PCs: C:\ProgramData\Labcenter Electronics\Proteus 8 Professional\
LIBRARY - use the folder that already holds Proteus's own .LIB files).
3. Copy TEPSIMCOM.DLL and TEPSERIALMON.DLL from "Proteus Model Files" to the
MODELS folder (...\Proteus 8 Professional\MODELS).
4. Updating from v1.0: replace TEPSIM800C.LIB (delete any TEPSIM800C.IDX) and
TEPSIMCOM.DLL. A v1.0 design keeps its v1.0 symbol: it runs with the new
model (without the v1.1 board parts and the red X) - re-pick the part to get
the v1.1 symbol.
5. Start Proteus. In Pick Devices (P) search "SIM800C": you get the Simple and
the Advance device (category Peripherals > Wireless).
RUN THE DEMO
"Proteus Simulation\SIM800C-SMS-Control-ArduinoUnoV3.pdsprj" - keep the .hex file
and the two DLLs beside the project. Both UNOs run SIM800C_SMS_Control.hex.
UNO 1 (ARD1): SIM800C Simple (U1, number +15555550101, its phone on the sheet
+15555550191) and Serial Monitor U3. UNO 2 (ARD2): SIM800C Advance (U2,
+15555550102, its phone in the pop-up window +15555550192) and Serial Monitor
U4. An LED (D1 / D2) on A0 of each UNO.
1. Press Run. Both monitor windows open (9600 baud) and so does U2's pop-up.
The HW-537 boards start OFF (the phones say MODULE OFF - HOLD PWX LOW 1 s);
the monitors show "Switching the SIM800C on (PWX LOW for 1.2 s)...",
"SIM800C found", "Waiting for SMS Ready... ok", the network, the signal,
the operator and the network time, then the command list (about 12 s of
simulation time).
2. U1: tap "SMS: LED ON" on the phone beside the module - U3 prints the SMS,
LED D1 lights and the reply "LED is ON" appears on the phone. Tap CALL -
the sketch shows the caller's number and rejects the call. Try NO SIGNAL,
tap an SMS (it waits at the SMS centre), then GOOD (it is delivered).
Close the phone with its red X and open it with PANEL on the board.
3. U3 / U4 quick buttons: AT+CSQ, AT+CREG? (sent to the SIM800C, its answer
is printed), STATUS, TEXT Hello from Arduino (an SMS to the last number
that texted the module - text it first). Type your own AT commands too.
4. U2 (Advance): the same phone is on its Phone page, with the MODULE /
NETWORK / TRAFFIC cards. Open the Test tab:
Network: Restart, 5 runs, Run test - the module is switched off and on
with its power key five times (watch U4: within 30 s the sketch
notices and sets it up again); then Radio off / on.
SMS round trip: STATUS, 5 runs - about 3.5 - 4.5 s per answer (1.2 -
1.9 s network in, a fraction of a second your sketch, 1.7 - 2.5 s
network out - different for every SMS, like a real network).
Call: 3 calls - the sketch rejects each a fraction of a second after the
first RING (its RI interrupt prints "(RI pin went LOW)" on U4).
AT check: the module's settings and the sketch's last AT commands.
5. Close U2's window and open it again with OPEN PANEL on the board.
Closed a monitor window? Click OPEN MONITOR on the monitor part.
WIRING (AltSoftSerial, the same on both UNOs)
SIM800C 5V -> supply, GND -> GND, TXD -> D8, RXD <- D9 (AltSoftSerial's fixed
UNO pins), PWX <- D7, RI -> D2 (INT0). LED + 220 ohm from A0 to GND.
The sketch pulls PWX LOW for 1.2 s (D7 as an OUTPUT LOW), then releases it as
an INPUT (the module pulls PWX up) - never drive PWX HIGH from a 5 V pin.
Serial Monitor RXD <- Arduino D1 (TX), Serial Monitor TXD -> Arduino D0 (RX),
Serial Monitor GND -> ground. RXD2 is not used in this demo: the D8 line lies
between the D9 -> RXD and D7 -> PWX wires, so a wire to it would cross one of
them - the sketch prints the module's answers itself (" < ..."). Wire RXD2
to the module's TXD in your own design to watch the raw AT traffic.
Serial.begin(9600) in the sketch.
In the sketch: AltSoftSerial gsm; gsm.begin(9600);
Pin order in Proteus: 5V GND TXD RXD PWX RI. The real HW-537 has two 8-pin rows
that also carry V_TTL, VBAT, DTR, VRTC and the audio pins.
REAL HARDWARE:
* The SIM800C chip itself needs 3.4 - 4.4 V (4.0 V typical) and draws up to
2 A peaks in its transmit bursts. The HW-537 board takes 5 V on its 5V pin
(two series diodes drop it for the module): use a 5 V supply that can
deliver 2 A peaks - NOT the Arduino's 5V pin - with a common GND.
* HW-537: tie V_TTL to the Arduino's logic supply (5 V on an UNO). It is the
reference of the TXD / RXD level shifter (two 2N7002); the TEP model assumes
it is connected and has no V_TTL pin. RI is probably not level shifted
(unverified) - check its level.
* A bare SIM800C module (or a board without the level shifter) has 2.8 V
logic: put a divider between the Arduino's D9 and RXD -
10 k from D9 to RXD and 12 k from RXD to GND gives about 2.7 V - and power
it from 3.4 - 4.4 V.
* 2G only: the SIM800C is a quad-band GSM / GPRS module (850 / 900 / 1800 /
1900 MHz); it does not work where the 2G network has been switched off.
WHY AltSoftSerial AND NOT SoftwareSerial
SoftwareSerial can send but cannot RECEIVE in Proteus 8.5: it needs pin-change
interrupts, which the Proteus 8.5 ATmega328P model never runs. AltSoftSerial
(Paul Stoffregen, MIT licence) uses Timer1 and works in Proteus and on real
boards. Don't use D10 while it runs (digitalRead / digitalWrite on D10 disturbs
its Timer1 output). The external interrupts INT0 / INT1 (D2 / D3) do work, so
the RI pin goes to D2. Your own SoftwareSerial sketches will show the module
working on its phone but the Arduino receiving nothing - use AltSoftSerial,
the hardware Serial port or an Arduino Mega (Serial1-3).
WHAT THE MODULE DOES
Power: the HW-537 board stays OFF after power-up (the phone says "MODULE OFF -
HOLD PWX LOW 1 s"). PWX held LOW for more than 1 s switches it on; held LOW
for more than 1 s while it runs gives NORMAL POWER DOWN and the module is off
2 s after the press began (55 ms after the release if you hold PWX longer);
held LOW for 33 s restarts it. With PWX tied to GND it switches on at
power-up (the usual auto-boot hack) and again after AT+CPOWD=1.
Start-up: right after switching on it sends the SIMCom sync bytes 00 49 49 49 49
FF FF FF FF at 115200 bps (meant for SIMCom's PC tool; at 9600 they can look
like a few garbage characters - normal). Then auto-bauding (factory
AT+IPR=0): the module sends nothing until it receives "AT" (AT / at / At /
aT) at any speed from 1200 to 115200 bps, then answers at that speed; its
serial port works about 2 s after switching on. A host that has sent "AT"
sees +CPIN: READY (3 s after switching on), Call Ready (4.5 s), SMS Ready
(5.5 s), then the network registration 2.2 - 3.2 s later. With a fixed speed
(AT+IPR=9600 then AT&W) every start reports RDY, +CFUN: 1 and +CPIN: READY at
that speed first. Every new simulation run starts from the factory settings.
Network: "searching" (+CREG: 0,2) until registered (+CREG: 0,1) to OPERATOR (a
repeatable spread per SIM number). Signal: GOOD = CSQ 21-23 (about -71 dBm),
WEAK = CSQ 7-9 (SMS take 2.5 x as long), NO SIGNAL = +CSQ: 99,99, not
registered, calls drop. AT+CFUN=0 switches the radio off (+CREG 0), AT+CFUN=1
searches again (+CREG: 2), AT+CFUN=1,1 answers OK and restarts the module
(its settings are lost and, auto-bauding, it waits for "AT" again).
SMS: text mode, the "> " prompt, Ctrl-Z sends, ESC cancels; the SIM800C answers
+CMGS: n only after delivery (1.7 - 2.5 s after Ctrl-Z, 4.25 - 6.25 s with
a weak signal). An SMS from the phone reaches the module after 1.2 - 1.9 s
(3 - 4.75 s weak). Every SMS gets its own time, like on a real network.
SMS sent to a module that is off or not registered wait at the "SMS
centre" and are delivered when it registers.
Calls: RING every 3 s, each followed by +CLIP: "+number",145,"",0,"",0 after
AT+CLIP=1. ATA answers, ATH rejects (the caller sees BUSY); an unanswered
call ends after 30 s.
NET LED: off while the module is off, 64 ms on / 800 ms off while searching,
64 ms on / 3 s off when registered. PWR LED: on whenever the board has 5 V
(even with the module off).
RI pin: HIGH normally, LOW while an incoming call rings, a 120 ms LOW pulse for
each new SMS.
The network is shared: every TEP SIM800C, every TEP SIM900A and every virtual
phone in the design can text and call the others by number (SIMNUM / PHONENUM).
THE PHONE (both devices)
Status bar with the network time and "TEP 2G"; a card with the module's number
and state (NO POWER - CHECK 5V / GND, MODULE OFF - HOLD PWX LOW 1 s, PWX LOW -
SWITCHING..., STARTING..., NORMAL POWER DOWN, SEARCHING FOR NETWORK, NO SIGNAL,
RADIO OFF, REGISTERED - operator), CSQ, stored SMS and the phone's own number;
the conversation as chat bubbles (blue = sent by the phone, green = received
from the module) with call events; during a call a bar shows INCOMING CALL /
CALLING / IN CALL mm:ss. A tip line reminds you of PWX or AT+CMGF=1.
Buttons:
CALL / ANSWER calls the SIM800C (the module shows RING + +CLIP), or answers
a call from the module (ATD<phone number>;)
HANG UP ends / rejects the call (the module gets NO CARRIER)
SMS: LED ON, SMS: LED OFF, SMS: STATUS, SMS: HELLO
text the SIM800C (delivered after 1.2 - 1.9 s)
NETWORK GOOD / WEAK / NO SIGNAL
Board: PWR and NET LEDs as above; the antenna's ring LED and tip lamp orange
while the module sends (SMS, call set-up), green while it receives, both in
turn during a call; the waves follow them.
THE TEST TOOLS (SIM800C Advance, Test tab) - what they really do
Network Restart: the tool switches the module off at once (like
AT+CPOWD=0) and on again with its power key (PWRKEY LOW for 1 s,
nothing is sent on TXD for it); each step is timed from the key
press: on 1.0 s, +CPIN READY 4.0 s, Call Ready 5.5 s, SMS Ready
6.5 s, registered about 8.7 - 9.7 s (example x5: 9.09 / 9.47 /
9.05 / 9.12 / 8.93 s). After a restart the settings are lost and the
module waits for "AT" - the v1.1 demo sketch sets it up again within
30 s. Radio off / on: AT+CFUN=0 for 1 s, then AT+CFUN=1; the time to
+CREG 1 (example x5: 2.28 - 3.06 s); the UART and settings stay. The
next run starts 2 s after a registration; no registration in 60 s =
a time-out. A power-down (PWX, AT+CPOWD) or a power loss stops the
test.
SMS The phone texts the command; the time until the sketch's reply SMS
reaches the phone, split into network in (phone -> module +CMT,
1.2 - 1.9 s), your sketch (+CMT -> its AT+CMGS) and the reply back
(AT+CMGS -> phone, 1.7 - 2.5 s + the UART time); the network parts
differ for every SMS, like on a real network. Example STATUS x5:
4.11 / 4.11 / 3.48 / 3.98 / 4.19 s (in 1.27 - 1.67 s, sketch
0.29 s, back 1.93 - 2.54 s). No reply in 30 s = no answer (the demo
sketch never answers unknown texts).
Call The phone calls; the first RING 2 s after dialling, then every 3 s;
+CLIP when AT+CLIP=1 (the module
…Development1 release
-
V1.1SIM800C GSM Library for Proteus V1.1this page
V1.1 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.
Installation10 steps
From the download to a working project, in order. The steps follow what the package contains.
You will need
- Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
- Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
- Any archive toolWindows, macOS and Linux extract ZIP files on their own
Steps
- 1
Extract the archive
Right-click sim800c-tep-v1-1-52adc4a1af6c40229f8ae3a42dbe6ada.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (SIM800C-TEP-v1.1) as it is.
- 2
Copy the library files into Proteus
Move ArduinoV3TEP.LIB, TEPSERIALMON.LIB and TEPSIM800C.LIB and ArduinoV3TEP.IDX into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.
- 3
Add the simulation model
Copy TEPSERIALMON.DLL and TEPSIMCOM.DLL into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.
- 4
Restart Proteus and place the component
Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.
- 5
Install the Arduino library
In the Arduino IDE choose Sketch → Include Library → Add .ZIP Library and pick the library, or copy its folder into Documents\Arduino\libraries. Restart the IDE to see its examples.
- 6
Open the sketch in the Arduino IDE
Open SIM800C_SMS_Control.ino, Echo.ino and ReceiveTest.ino, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.
- 7
Load the HEX file
In Proteus double-click the microcontroller, set Program File to SIM800C_SMS_Control.hex and run the simulation. For real hardware, flash the same file with your programmer.
- 8
Open the example simulation
Open SIM800C-SMS-Control-ArduinoUnoV3.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.
- 9
Use the data files
library.json hold the readings or settings the project uses; open them with Excel, a text editor or the script of the tutorial.
- 10
Follow the tutorial
SIM800C Library for Proteus V1.1 (GSM Module + Arduino) explains every connection and setting in order; keep it open beside the files while you build.
FAQs9 questionsContact TEP
How do I download SIM800C GSM Library for Proteus V1.1?
Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.
What is inside the archive?
SIM800C GSM Library for Proteus V1.1 comes as a ZIP archive of 23 files (1.4 MB, 3.2 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and data files. Open the File Structure tab for the full list of 23 files.
What should I do if the download does not start?
Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.
Is this file free?
Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.
How do I check that the file arrived complete?
Compare its SHA-256 with the one on this page, a59aca0119815b52a9aa7d8639eccf08ce711a1092b387e0eb941f57b2da7b77. In PowerShell run Get-FileHash "sim800c-tep-v1-1-52adc4a1af6c40229f8ae3a42dbe6ada.zip"; on macOS or Linux run shasum -a 256 "sim800c-tep-v1-1-52adc4a1af6c40229f8ae3a42dbe6ada.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.
Do I need WinRAR to open the ZIP file?
No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.
Where do I put the LIB and IDX files?
Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.
Which Proteus version does the library need?
The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.
How do I get the HEX file into the simulation?
Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.
Members skip the wait. Log in or join TEP.
- 10Total downloads
- 4%Popularity
- ProteusCategory
- 0Comments
- ssyedzainnasirUploaded by
- 6 Oct 2026Uploaded at
a59aca0119815b52a9aa7d8639eccf08ce711a1092b387e0eb941f57b2da7b77





















Comments
0