TEP DOWNLOAD CENTER

Project Files of SIM900A Library for Proteus V1.1 (GSM Module + Arduino)

Libraries Code Projects Simulation
tep://download-terminal sim900a-tep-v1-1-6b3d2154368a46b29e28f4d90475fc77.zip ZIP archiveV1.1Verified7 downloadsFree
SIM900A Library for Proteus V1.1: two Arduino UNOs with SIM900A modules, the SIM900A Advance pop-up with an SMS chat and the TEP Serial Monitor in its Simple interface
Proteus library · File 1 of 1

SIM900A GSM Library for Proteus V1.1

SIM900A GSM Library for Proteus V1.1 comes as a ZIP archive of 23 files (1.4 MB, 3.1 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and data files.

  • LIBProteus library
  • IDXProteus library index
  • DLLProteus model
  • DSNProteus simulation
  • INOArduino sketch
  • LIBArduino library
  • HEXHEX firmware
  • CSVData file

Description

This is the download page of SIM900A GSM Library for Proteus V1.1, the file package of the tutorial SIM900A Library for Proteus V1.1 (GSM Module + Arduino), published on The Engineering Projects in October 2026. Here you get the ZIP file (1.4 MB) with the Proteus library files (LIB and IDX), the simulation model (DLL), a ready Proteus simulation, an Arduino sketch, an Arduino library, the compiled HEX firmware and data files, the list of files it contains, the README when there is one, and the installation steps in order.

What this library is

SIM900A-GSM-Library-for-Proteus-v1.1.zip with SIM900A Simple and Advance (TEPSIM900A.LIB and TEPSIMCOM.DLL), the TEP Serial Monitor and Arduino UNO libraries for Proteus, the SMS remote control simulation with its HEX file, the demo sketch with the AltSoftSerial 1.4 library and a README.

This is version 1.1; older or newer releases, when they exist, are listed in the Development tab.

What is inside the ZIP file

  • ArduinoV3TEP.LIB – Proteus library, 95.6 KB
  • TEPSERIALMON.LIB – Proteus library, 11.1 KB
  • TEPSIM900A.LIB – Proteus library, 75.9 KB
  • ArduinoV3TEP.IDX – Library index, 830 B
  • TEPSERIALMON.DLL – Simulation model, 978 KB
  • TEPSIMCOM.DLL – Simulation model, 472 KB
  • and 17 more, all listed in the File Structure tab

The archive unpacks to 3.1 MB and carries its own README (README.txt), shown in the README tab above.

How to download

Use the download panel at the top of this page: after the counter (30 seconds for guests, 10 for members) the black button unlocks and the ZIP file comes straight from our content network. If the browser opens it instead of saving, use Save as; extract the whole archive before using anything inside it.

How to install

  • Step 1: Extract the ZIP file with Windows (Extract All), 7-Zip or WinRAR, keeping its folders.
  • Step 2: Close Proteus and copy ArduinoV3TEP.LIB, TEPSERIALMON.LIB and TEPSIM900A.LIB and ArduinoV3TEP.IDX into its LIBRARY folder (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY).
  • Step 3: Copy TEPSERIALMON.DLL and TEPSIMCOM.DLL into the MODELS folder next to it, so the part simulates.
  • Step 4: Start Proteus, press P and search for "ArduinoV3TEP"; place and wire it as in the tutorial.
  • Step 5: In the Arduino IDE use Sketch → Include Library → Add .ZIP Library, then restart the IDE.
  • Step 6: Open SIM900A_SMS_Control.ino, Echo.ino and ReceiveTest.ino in the Arduino IDE, pick board and port and Verify (Export Compiled Binary gives the HEX).
  • Step 7: In Proteus set the controller's Program File to SIM900A_SMS_Control.hex; on hardware, flash the same file.
  • Step 8: Open SIM900A-SMS-Control-ArduinoUnoV3.pdsprj in Proteus and press Play.

Read the detailed guide

This page is for the files. The full tutorial, SIM900A Library for Proteus V1.1 (GSM Module + Arduino), explains the circuit and the code step by step and shows the working results and the simulation; read it before you build. Questions about the download or the installation go in the comments below; more Proteus downloads are listed further down this page.

Read SIM900A Library for Proteus V1.1 (GSM Module + Arduino)

File Structure

sim900a-tep-v1-1-6b3d2154368a46b29e28f4d90475fc77.zip23 files · 9 folders · 3.1 MB unpacked
SIM900A-TEP-v1.1/23 files · 3.1 MB
Arduino Code/12 files · 44.1 KB
libraries/11 files · 30.1 KB
AltSoftSerial/11 files · 30.1 KB
config/2 files · 14.4 KB
LIB AltSoftSerial_Boards.hArduino library file 4.6 KB
LIB AltSoftSerial_Timers.hArduino library file 9.8 KB
examples/2 files · 2.3 KB
Echo/1 file · 968 B
INO Echo.inoArduino sketch 968 B
ReceiveTest/1 file · 1.4 KB
INO ReceiveTest.inoArduino sketch 1.4 KB
LIB AltSoftSerial.cppArduino library file 8.3 KB
LIB AltSoftSerial.hArduino library file 2.5 KB
TXT keywords.txtText file 82 B
CSV library.jsonData file 441 B
LIB library.propertiesArduino library file 422 B
TXT LICENSE.txtText file 1.3 KB
MD README.mdReadme 384 B
SIM900A_SMS_Control/1 file · 14 KB
INO SIM900A_SMS_Control.inoArduino sketch 14 KB
Proteus Library Files/4 files · 183.4 KB
IDX ArduinoV3TEP.IDXLibrary index 830 B
LIB ArduinoV3TEP.LIBProteus library 95.6 KB
LIB TEPSERIALMON.LIBProteus library 11.1 KB
LIB TEPSIM900A.LIBProteus library 75.9 KB
Proteus Model Files/2 files · 1.4 MB
DLL TEPSERIALMON.DLLSimulation model 978 KB
DLL TEPSIMCOM.DLLSimulation model 472 KB
Proteus Simulation/4 files · 1.5 MB
DSN SIM900A-SMS-Control-ArduinoUnoV3.pdsprjProteus simulation 25.4 KB
HEX SIM900A_SMS_Control.hexCompiled HEX file 33.6 KB
DLL TEPSERIALMON.DLLSimulation model 978 KB
DLL TEPSIMCOM.DLLSimulation model 472 KB
TXT README.txtText file 37.3 KB

README

README.txt 362 lines
SIM900A GSM / GPRS MODULE (SIMCom, SIM900A MINI board) LIBRARY FOR PROTEUS - V1.1
Designed by The Engineering Projects
www.TheEngineeringProjects.com

IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
  https://www.theengineeringprojects.com/2026/10/sim900a-library-for-proteus.html
Report a bug or suggest a feature (our forum):
  https://www.theengineeringprojects.com/forum/category/sim900a-proteus-library
The demo uses our TEP Serial Monitor Advance (included) instead of Proteus's
Virtual Terminal - its own article:
  https://www.theengineeringprojects.com/2026/10/serial-monitor-advance-proteus-library.html

FILE STRUCTURE
SIM900A-TEP-v1.1/
|-- Proteus Library Files/
|   |-- ArduinoV3TEP.IDX                              0.8 KB   its index -> LIBRARY folder
|   |-- ArduinoV3TEP.LIB                             95.6 KB   TEP Arduino UNO (demo) -> LIBRARY folder
|   |-- TEPSERIALMON.LIB                             11.1 KB   TEP Serial Monitor Advance -> LIBRARY folder
|   |-- TEPSIM900A.LIB                               75.9 KB   SIM900A Simple + Advance (2 devices) -> LIBRARY folder
|-- Proteus Model Files/
|   |-- TEPSERIALMON.DLL                            978.0 KB   Serial Monitor model -> MODELS folder
|   |-- TEPSIMCOM.DLL                               472.0 KB   SIM900A model (shared with the SIM800C library) -> MODELS
|-- Proteus Simulation/
|   |-- SIM900A_SMS_Control.hex                      33.6 KB   both UNOs (SMS remote control v1.1)
|   |-- SIM900A-SMS-Control-ArduinoUnoV3.pdsprj      25.4 KB   demo: UNO 1 + SIM900A Simple, UNO 2 + Advance
|   |-- TEPSERIALMON.DLL                            978.0 KB   copy of the monitor model
|   |-- TEPSIMCOM.DLL                               472.0 KB   copy of the model so the demo runs as is
|-- Arduino Code/
|   |-- SIM900A_SMS_Control/SIM900A_SMS_Control.ino   14.0 KB   sketch (source of the .hex)
|   |-- libraries/AltSoftSerial/                     30.1 KB   AltSoftSerial 1.4 (MIT, LICENSE.txt), 11 files
|-- README.txt                                      ~38.2 KB   this file
Total: 3.15 MB (unzipped). The C++ source code of the model is not included.

WHAT IS IT?
A simulation model of the SIMCom SIM900A GSM / GPRS module on the popular blue
"SIM900A MINI" V3.8.2 board for Proteus 8. It talks to your Arduino like the
real one: the mini board switches the module on by itself, it learns the baud
rate from the first "AT" (auto-bauding), sends +CPIN: READY, registers to the
network and only THEN sends "Call Ready" (the SIM900A has no "SMS Ready"), and
answers the AT commands for SMS (text mode), calls, the network, the clock and
USSD. Its REGIONLOCK property shows what the Asia-locked stock firmware does in
an unlisted country (Pakistan, for example): +CPIN: PH-NET PIN and no
registration. Next to the module there is a virtual smartphone with its own
number: it texts the module, calls it, answers its calls and shows the SMS it
receives as chat bubbles. Every TEP SIM900A, every TEP SIM800C and every
virtual phone in a design share one simulated network, so modules can also
text and call each other. The part looks like the blue SIM900A MINI board with
its flip SIM holder, the SIM900A can and the rubber-duck antenna on an SMA
jack. While the simulation runs the red PWR LED shows the board's 5 V, LED D5
follows the RI signal (lit at idle, dark while a call rings, a flicker for each
SMS), LED D6 blinks like the real NETLIGHT (slow while searching, every 3 s
when registered), the duck's coloured ring and the lamp in its tip light
orange while the module sends and green while it receives, and the radio waves
above the antenna ripple out (sending) or in (receiving).

TWO DEVICES IN ONE LIBRARY (search "SIM900A" or "GSM" in Pick Devices):
  SIM900A Simple    device SIM900ATEP     "SIM900A GSM / GPRS Module (SIMCom, SIM900A MINI board) - Simple"
                    On-Sheet Panel: the virtual phone is drawn on the schematic
                    next to the module (the v1.0 phone) - click its CALL, HANG UP,
                    SMS and NETWORK buttons. The red X in the phone's app bar
                    closes it, the PANEL button on the board opens it again.
                    Your v1.0 designs keep working with this device.
  SIM900A Advance   device SIM900AADVTEP  "SIM900A GSM / GPRS Module (SIMCom, SIM900A MINI board) - Advance"
                    Pop-Up Panel: only the module board on the schematic; at Run
                    a TEP pop-up window opens - the same look as the TEP Serial
                    Monitor (move it by its header, resize it, minimise it). The
                    tabs Phone and Test sit in the header; the gear and ? icons
                    open Settings and Help; the palette icon switches the theme:
                      Phone     the virtual phone redrawn for the window (signal
                                bars, chat bubbles, call bar, CALL / ANSWER, HANG
                                UP, the four SMS, GOOD / WEAK / NO SIGNAL) beside
                                three cards: MODULE (number, IMEI, firmware, UART
                                speed, the settings your sketch made, power and
                                start-ups, the REGION LOCK), NETWORK (registration,
                                CSQ and dBm, operator, how long it is registered
                                and how long the search took, whether +CPIN: READY
                                and Call Ready came, the NETLIGHT pattern) and
                                TRAFFIC (SMS sent / received / waiting at the SMS
                                centre, stored on the SIM, calls, AT commands and
                                errors, the last AT command with its reply and
                                response time)
                      Test      four GSM test tools, all measured on the model:
                                Network - the module really restarts (switched off;
                                  the mini board's PWRKEY switches it on again
                                  1 s later) or switches its radio off and on
                                  (AT+CFUN=0 / 1) 3, 5 or 10 times: the time of
                                  power-on, +CPIN READY and the registration with
                                  its Call Ready of each run, fastest / average /
                                  slowest (a region-locked module never registers:
                                  the tool tells you so instead of starting)
                                SMS round trip - the phone texts LED ON, LED OFF,
                                  STATUS or HELLO 3, 5 or 10 times; each reply SMS
                                  from your sketch stops the clock: network in +
                                  your sketch + the reply back, answered / no
                                  answer, the reply text
                                Call - the phone calls the module 1, 3 or 5 times:
                                  the first RING, the RING URCs, the module's own
                                  +CLIP line (the SIM900 format with the empty
                                  field), the RI signal (LED D5: how often and how
                                  long LOW), whether your sketch answers (ATA) or
                                  rejects (ATH) and after how long; a timeline
                                AT check - what the AT queries answer right now
                                  (AT+CPIN? AT+CSQ AT+CREG? AT+COPS? AT+CMGF?
                                  AT+CNMI? AT+CLIP? AT+CMEE? AT+CFUN? AT+IPR?
                                  AT+CCALR? AT+CCLK?) and the last 8 AT commands
                                  your Arduino sent with the reply and the
                                  response time
                      Settings  theme (TEP Dark / Light), text size, open at Run,
                                window size - remembered for your Windows user
                      Help      Help & Support like the TEP Serial Monitor: report
                                a bug, suggest a feature, article, user guide,
                                updates, donate, website, forum; Copy diagnostics
                                (module, network, traffic, test results) for a
                                bug report
                    The OPEN PANEL button on the board opens the window again
                    after you close it.
Both devices use the same model and the same properties.

ONE MODEL FOR TWO LIBRARIES
The model TEPSIMCOM.DLL (the same name as in v1.0) is shared with the SIM800C
library: the TEP SIM800C GSM library ships the identical TEPSIMCOM.DLL (the
same bytes), so installing both libraries is safe - copying the DLL twice just
overwrites it with itself. A SIM900A and a SIM800C in the same design can text
and call each other.

NEW IN V1.1
* The SIM900A and the SIM800C are now two separate libraries (TEPSIM900A.LIB and
  TEPSIM800C.LIB, one package each), with one shared model DLL.
* Two devices: SIM900A Simple (phone on the sheet, close / open) and SIM900A
  Advance (pop-up window with the phone, test tools, settings and help) - see
  above. The Advance device has its own default numbers (+15555550202 / phone
  +15555550292), so a Simple and an Advance module in one design stay distinct.
* Board: a red PWR LED (new), the duck's coloured ring is now a ring LED and its
  tip a lamp (orange = sending, green = receiving), a PANEL / OPEN PANEL button
  and a SIMPLE / ADVANCE badge; the SIM900A can moved up so the title fits under
  it, and D6 moved off the SMA jack it touched in v1.0. D5 and D6 keep their
  real behaviour.
* Model: the network search now takes 2.2 - 3.2 s (weak signal 2.8 - 3.4 s,
  v1.0: always 3 s), so Call Ready comes 6.2 - 7.2 s after power-up; every SMS
  takes its own time on the network, like on a real one: 1.2 - 1.9 s from the
  phone to the module, 1.7 - 2.5 s from the module to the phone, +CMGS after
  0.6 - 0.85 s (v1.0: always 1.5 s, 2 s and 0.7 s; with a weak signal 2.5 x
  as long); AT+CFUN=1 after AT+CFUN=0 reports +CREG: 2 (searching);
  AT+CFUN=1,1 answers OK completely before it restarts (v1.0 restarted after a
  fixed 30 ms, which cut the OK at slow baud rates); the phone shows 60
  characters per message (v1.0 cut longer replies at 32); every module event
  reaches the Simulation Log.
* The demo uses the TEP Serial Monitor Advance instead of Virtual Terminals -
  one monitor per Arduino (U3 = UNO 1, U4 = UNO 2) with quick buttons, and the
  module's 5VT line on each monitor's second input RXD2 (the v1.0 "line
  monitor") - and shows both styles: UNO 1 with SIM900A Simple, UNO 2 with
  SIM900A Advance, an LED on A0 of each UNO.
* The demo sketch (v1.1) also takes commands from the Serial Monitor (AT lines
  go to the SIM900A and its answer is printed, STATUS, TEXT <message>, HELP),
  and every 30 s it checks the module: after a restart (the module then forgets
  its settings) it sets the SIM900A up again.
* Version 1.1 everywhere; the C++ source code is no longer included.

TEST STATUS
v1.0 was tested in Proteus 8.5 SP0 (1 Oct 2026) with the v1.0 demo: the mini
board switched the SIM900A on, the sketch saw Call Ready after registration
(CSQ 22, TEP MOBILE), answered STATUS by SMS and rejected a call; the line
monitor showed +CLIP: "+15555550291",145,"",,"",0 (the SIM900 format).
v1.1 was tested in Proteus 8.5 SP0 (6 Oct 2026) with this package's demo: both
Serial Monitors and the Advance pop-up open at Run (no system caption row);
both modules start by themselves, register (TEP MOBILE) and the sketches see
Call Ready. U1 (Simple): SMS LED ON / LED OFF / STATUS / HELLO from the phone
(D1 lights, replies in the chat), CALL (rejected with ATH; RXD2 shows the
SIM900 +CLIP with its empty field ,"",,"",0), NO SIGNAL (+CREG: 0,2), the red X
and PANEL, and REGIONLOCK = YES (the phone turns red, the sketch prints the
+CPIN: PH-NET PIN explanation). U2 (Advance): the phone, Test > Network restart
x 5 (6.35 - 6.75 s, Call Ready together with the registration), SMS round trip
x 5 (3.60 - 4.46 s), Call x 3, AT check (+CMGS after about 0.7 s, before the
delivery), Settings, Help, close and OPEN PANEL.
PC tests: 1667 automatic checks
on a PC (for the shared model, both modules): 243 on the module model at the
pin level (auto power-on, sync bytes, auto-bauding, identity strings, Call
Ready after registration, SMS, calls and +CLIP, no signal and the SMS centre,
USSD, clock and network time, AT+CPOWD and the automatic restart, fixed baud
rate, the region lock, and the v1.1 network spread, SMS times, AT+CFUN, AT log
and test tools with their measured times); 95 with the two real demo sketches
running against the model (start-up wherever the UNO starts, the region lock
message, SMS commands, calls, an UNO reset, the Serial Monitor commands, the
pop-up's tools with the real sketch, setting the module up again after a
restart and after AT+CFUN=1,1); 222 on the complete Proteus model (all four
devices, the LEDs and the antenna ring, the phone close / open, a v1.0 design,
the pop-up window, its pages and buttons, the four test tools, a region-locked
module); 1107 on the rendered pop-up windows (every tool's hint lines fit the
window).

INSTALLATION (about 2 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" (TEPSIM900A.LIB with both devices,
   TEPSERIALMON.LIB and the TEP Arduino UNO V3 library ArduinoV3TEP.LIB / .IDX
   used by the demo) to the LIBRARY folder of Proteus, for example:
     C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
   (on some PCs: C:\ProgramData\Labcenter Electronics\Proteus 8 Professional\
   LIBRARY - use the folder that already holds Proteus's own .LIB files).
3. Copy TEPSIMCOM.DLL and TEPSERIALMON.DLL from "Proteus Model Files" to the
   MODELS folder (...\Proteus 8 Professional\MODELS).
4. Updating from v1.0: replace TEPSIM900A.LIB (delete any TEPSIM900A.IDX) and
   TEPSIMCOM.DLL. A v1.0 design keeps its v1.0 symbol: it runs with the new
   model (without the v1.1 board parts and the red X; D6 blinks at its v1.0
   place) - re-pick the part to get the v1.1 symbol.
5. Start Proteus. In Pick Devices (P) search "SIM900A": you get the Simple and
   the Advance device (category Peripherals > Wireless).

RUN THE DEMO
"Proteus Simulation\SIM900A-SMS-Control-ArduinoUnoV3.pdsprj" - keep the .hex file
and the two DLLs beside the project. Both UNOs run SIM900A_SMS_Control.hex.
  UNO 1 (ARD1): SIM900A Simple (U1, number +15555550201, its phone on the sheet
  +15555550291) and Serial Monitor U3. UNO 2 (ARD2): SIM900A Advance (U2,
  +15555550202, its phone in the pop-up window +15555550292) and Serial Monitor
  U4. An LED (D1 / D2) on A0 of each UNO.
  1. Press Run. Both monitor windows open (9600 baud) and so does U2's pop-up.
     The monitors show "Waiting for the SIM900A...", "SIM900A found", "Waiting
     for Call Ready (sent after network registration)... ok", the network, the
     signal, the operator and the network time, then the command list (about
     8 s of simulation time). The amber RX2 lines are the module's own 5VT
     output (the raw AT traffic), the white ones the sketch's text.
  2. U1: tap "SMS: LED ON" on the phone beside the module - U3 prints the SMS,
     LED D1 lights and the reply "LED is ON" appears on the phone. Tap CALL -
     the sketch shows the caller's number and rejects the call (D5 goes dark
     while it rings). Try NO SIGNAL, tap an SMS (it waits at the SMS centre),
     then GOOD (it is delivered). Close the phone with its red X and open it
     with PANEL on the board.
  3. U3 / U4 quick buttons: AT+CSQ, AT+CREG? (sent to the SIM900A, its answer
     is printed), STATUS, TEXT Hello from Arduino (an SMS to the last number
     that texted the module - text it first). Type your own AT commands too
     (AT+CPIN? shows the region lock).
  4. U2 (Advance): the same phone is on its Phone page, with the MODULE /
     NETWORK / TRAFFIC cards. Open the Test tab:
       Network: Restart, 5 runs, Run test - the module restarts five times
         (watch U4: within 30 s the sketch notices and sets it up again); then
         Radio off / on.
       SMS round trip: STATUS, 5 runs - about 3.5 - 4.5 s per answer (1.2 -
         1.9 s network in, a fraction of a second your sketch, 1.7 - 2.5 s
         network out - different for every SMS, like a real network).
       Call: 3 calls - the sketch rejects each a fraction of a second after the
         first RING; the card shows the SIM900's +CLIP line.
       AT check: the module's settings and the sketch's last AT commands.
  5. Close U2's window and open it again with OPEN PANEL on the board.
  6. Region lock: stop, double-click U1 > REGIONLOCK = YES, Run - U3 prints
     "REGION LOCK: AT+CPIN? -> +CPIN: PH-NET PIN" and the phone turns red.
Closed a monitor window? Click OPEN MONITOR on the monitor part.

WIRING (AltSoftSerial, the same on both UNOs)
  SIM900A VCC5 -> supply, GND -> GND, 5VT (module TXD, 5 V level) -> D8,
  5VR (module RXD, 5 V level) <- D9 (AltSoftSerial's fixed UNO pins). No power
  or reset pin to drive - the mini board switches the module on by itself.
  LED + 220 ohm from A0 to GND.
  Serial Monitor RXD <- Arduino D1 (TX), Serial Monitor TXD -> Arduino D0 (RX),
  Serial Monitor GND -> ground, Serial Monitor RXD2 <- the module's 5VT line
  (a junction on the 5VT -> D8 wire; BAUD2 9600). Serial.begin(9600) in the
  sketch.
In the sketch: AltSoftSerial gsm;   gsm.begin(9600);
Pin order in Proteus: VCC5 GND 5VT 5VR. The real SIM900A mini TTL header also has
3VT / 3VR (3.3 V level), and some versions VCC4 and VCC_MCU.
REAL HARDWARE:
 * The SIM900A MINI takes 5 V on VCC5 (its regulator feeds the module), but the
   module draws up to 2 A in its transmit bursts: use a 5 V supply that can
   deliver 2 A peaks (sellers ask for "5V DC above 1A") - NOT the Arduino's 5V
   pin - with a common GND.
 * Logic levels: use 5VT / 5VR with a 5 V Arduino such as the UNO (no divider
   needed), 3VT / 3VR with a 3.3 V board. VCC4 is the direct battery input
   (3.5 - 4.5 V): never give it 5 V - the module shuts down with an
   over-voltage error.
 * 2G only: the SIM900A is a dual-band GSM / GPRS module (900 / 1800 MHz); it
   does not work where the 2G network has been switched off.
 * Region lock: stock SIM900A firmware only works in its Asian country list -
   see THE SIM900A REGION LOCK below.

WHY AltSoftSerial AND NOT SoftwareSerial
SoftwareSerial can send but cannot RECEIVE in Proteus 8.5: it needs pin-change
interrupts, which the Proteus 8.5 ATmega328P model never runs. AltSoftSerial
(Paul Stoffregen, MIT licence) uses Timer1 and works in Proteus and on real
boards. Don't use D10 while it runs (digitalRead / digitalWrite on D10 disturbs
its Timer1 output). Your own SoftwareSerial sketches will show the module
working on its phone but the Arduino receiving nothing - use AltSoftSerial,
the hardware Serial port or an Arduino Mega (Serial1-3).

WHAT THE MODULE DOES
Power: the mini board holds PWRKEY low: the module switches on by itself 1 s
  after power-up, and after AT+CPOWD=1 (NORMAL POWER DOWN, off 1.7 s later) it
  restarts by itself 1.5 s later.
Start-up: right after switching on it sends the SIMCom sync bytes 00 49 49 49 49
  FF FF FF FF at 115200 bps (meant for SIMCom's PC tool; at 9600 they can look
  like a few garbage characters - normal). Then auto-bauding (factory
  AT+IPR=0): the module sends nothing until it receives "AT" or "At" (upper-case
  A only) at any speed from 1200 to 115200 bps, then answers at that speed; its
  serial port works about 2.2 s after switching on. A host that has sent "AT"
  sees +CPIN: READY (3 s after switching on), the network registration 2.2 -
  3.2 s later, THEN Call Ready. The SIM900A has no "SMS Ready". With a fixed
  speed (AT+IPR=9600 then AT&W) every start reports RDY, +CFUN: 1 and +CPIN:
  READY at that speed first. Every new simulation run starts from the factory
  settings.
Network: "searching" (+CREG: 0,2) until registered (+CREG: 0,1) to OPERATOR (a
  repeatable spread per SIM number). Signal: GOOD = CSQ 21-23, WEAK = CSQ 7-9
  (SMS take 2.5 x as long), NO SIGNAL = +CSQ: 0,0 (as the real SIM900A
  reports it), not registered, calls drop. AT+CFUN=0 switches the radio off
  (+CREG 0), AT+CFUN=1 searches again (+CREG: 2), AT+CFUN=1,1 answers OK and
  restarts the module (its settings are lost and, auto-bauding, it waits for
  "AT" again).
SMS: text mode, the "> " prompt (after the echoed line end), Ctrl-Z sends, ESC
  cancels; the SIM900A answers +CMGS: n as soon as the SMS centre has the
  message (0.6 - 0.85 s after Ctrl-Z) - the SMS itself reaches the other side
  later, 1.7 - 2.5 s after Ctrl-Z (the real SIM900 answers +CMGS promptly, the
  SIM800 only after delivery). An SMS from the phone reaches the module after
  1.2 - 1.9 s. Every SMS gets its own time, like on a real network; with a
  weak signal all of them take 2.5 x as long. SMS sent to a module that is off
  or not registered wait at the "SMS centre" and are delivered when it
  registers.
Calls: RING every 3 s, each followed by +CLIP: "+number",145,"",,"",0 (the
  SIM900 format with the empty field) after AT+CLIP=1. ATA answers, ATH rejects
  (the caller sees BUSY); an unanswered call ends after 30 s.
LEDs: D5 follows the RI signal (not on the TTL header): lit at idle, dark while
  a call rings, a short off-flicker for each new SMS. D6 = NETLIGHT: off while
  the module is off, 64 ms on / 800 ms off while searching, 64 ms on / 3 s off
  when registered. PWR: on whenever the board has 5 V (also while the module
  restarts).
The network is shared: every TEP SIM900A, every TEP SIM800C and every virtual
phone in the design can text and call the others by number (SIMNUM / PHONENUM).

THE SIM900A REGION LOCK (PROPERTY REGIONLOCK)
Stock SIM900A firmware (from build 1137B06SIM900A32_ST on) only works in a list
of Asian countries: China, India, Singapore, Malaysia, Thailand, Indonesia,
Cambodia, Vietnam, Laos, Burma, Brunei, Philippines and East Timor. Pakistan,
for example, is not in the list. Set REGIONLOCK = YES on the SIM900A to see what
such a module does in an unlisted country:
 * it still reports +CPIN: READY at start-up, but AT+CPIN? answers
   +CPIN: PH-NET PIN;
 * it never registers: +CREG: 2 (searching, 4 s) and +CREG: 0 (refused, 26 s)
   again and again, so D6 keeps blinking about once a second and Call Ready
   never comes;
 * AT+CSQ still reports the signal and AT+COPS=? still lists the operator, but
   selecting it (AT+COPS=1,0,"...") answers ERROR (and +CREG: 3 after
   AT+CREG=1);
 * the phone card turns red "REGION LOCKED - PH-NET PIN" with the tip
   "REGION LOCK: REFLASH SIM900 FIRMWARE ON REAL HARDWARE"; the Advance
   window's MODULE card says YES in red, its AT check shows +CPIN: PH-NET PIN
   and the Network test explains why it cannot run; the Simulation Log explains
   it too.
The demo sketch detects it and prints:
  REGION LOCK: AT+CPIN? -> +CPIN: PH-NET PIN
    Stock SIM900A firmware only works in its Asian country list, so this
    network refuses it. Reflash SIM900 firmware (e.g. 1137B09SIM900B32_ST).
then waits about 30 s for the network ("... NOT registered") and ends its
start-up with "Region locked - SMS and calls will not work on this network".
On real hardware the fix is to flash SIM900 firmware (e.g. 1137B09SIM900B32_ST
for 32 Mbit flash, or a 1137B0xSIM900M64_ST build for 64 Mbit) with SIMCom's
"SIM900 Series download Tools"; afterwards AT+CGMM answers SIMCOM_SIM900.
REGIONLOCK = NO (the default) behaves like an unlocked module.

THE PHONE (both devices)
Status bar with the network time and "TEP 2G"; a card with the module's number
and state (NO POWER - CHECK VCC5 / GND, STARTING..., RESTARTING..., NORMAL POWER
DOWN, SEARCHING FOR NETWORK, NO SIGNAL, RADIO OFF, REGION LOCKED - PH-NET PIN,
REGISTERED - operator), CSQ, stored SMS and the phone's own number; the
conversation as chat bubbles (blue = sent by the phone, green = received from
the module) with call events; during a call
…
Advertisement

Development1 release

  1. V1.1SIM900A GSM Library for Proteus V1.1this page

    V1.1 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.

Installation10 steps

From the download to a working project, in order. The steps follow what the package contains.

You will need

  • Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
  • Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
  • Any archive toolWindows, macOS and Linux extract ZIP files on their own

Steps

  1. 1

    Extract the archive

    Right-click sim900a-tep-v1-1-6b3d2154368a46b29e28f4d90475fc77.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (SIM900A-TEP-v1.1) as it is.

  2. 2

    Copy the library files into Proteus

    Move ArduinoV3TEP.LIB, TEPSERIALMON.LIB and TEPSIM900A.LIB and ArduinoV3TEP.IDX into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.

  3. 3

    Add the simulation model

    Copy TEPSERIALMON.DLL and TEPSIMCOM.DLL into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.

  4. 4

    Restart Proteus and place the component

    Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.

  5. 5

    Install the Arduino library

    In the Arduino IDE choose Sketch → Include Library → Add .ZIP Library and pick the library, or copy its folder into Documents\Arduino\libraries. Restart the IDE to see its examples.

  6. 6

    Open the sketch in the Arduino IDE

    Open SIM900A_SMS_Control.ino, Echo.ino and ReceiveTest.ino, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.

  7. 7

    Load the HEX file

    In Proteus double-click the microcontroller, set Program File to SIM900A_SMS_Control.hex and run the simulation. For real hardware, flash the same file with your programmer.

  8. 8

    Open the example simulation

    Open SIM900A-SMS-Control-ArduinoUnoV3.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.

  9. 9

    Use the data files

    library.json hold the readings or settings the project uses; open them with Excel, a text editor or the script of the tutorial.

  10. 10

    Follow the tutorial

    SIM900A Library for Proteus V1.1 (GSM Module + Arduino) explains every connection and setting in order; keep it open beside the files while you build.

How to add a library in Proteus 8 Run the HEX file in the Uno Test Bench, in your browser

FAQs9 questionsContact TEP

How do I download SIM900A GSM Library for Proteus V1.1?

Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.

What is inside the archive?

SIM900A GSM Library for Proteus V1.1 comes as a ZIP archive of 23 files (1.4 MB, 3.1 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and data files. Open the File Structure tab for the full list of 23 files.

What should I do if the download does not start?

Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.

Is this file free?

Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.

How do I check that the file arrived complete?

Compare its SHA-256 with the one on this page, 6ccc383e18f406e8e26dfd84ea015c7f3b8bea9daa44494e6e73a90e5c36a929. In PowerShell run Get-FileHash "sim900a-tep-v1-1-6b3d2154368a46b29e28f4d90475fc77.zip"; on macOS or Linux run shasum -a 256 "sim900a-tep-v1-1-6b3d2154368a46b29e28f4d90475fc77.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.

Do I need WinRAR to open the ZIP file?

No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.

Where do I put the LIB and IDX files?

Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.

Which Proteus version does the library need?

The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.

How do I get the HEX file into the simulation?

Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.

preparing · sim900a-tep-v1-1-6b3d2154368a46b29e28f4d90475fc77.zip
Rating
Your download will be ready shortly
Preparing your download…

Members skip the wait. Log in or join TEP.

  • 7Total downloads
  • 4%Popularity
  • ProteusCategory
  • 0Comments
  • ssyedzainnasirUploaded by
  • 6 Oct 2026Uploaded at
Last 14 days7 downloads
SHA-256 6ccc383e18f406e8e26dfd84ea015c7f3b8bea9daa44494e6e73a90e5c36a929
DocumentationSIM900A Library for Proteus V1.1 (GSM Module + Arduino)
Advertisement

Comments

0

Join the conversation

Start the conversationAsk a question or share how you used this download.